H.P.A.
Dear Installer, Congratulations on your choice of a MetaSystem product! We would like to ask you to read the instructions in this manual carefully as you will find it contains useful information to get acquainted with the many possibilities that the H.P.A (High Performance Alarm) range of products is able to offer.
THE H.P.A. RANGE Rel.
INSTRUCTIONS FOR INSTALLATION INSTALLATION CONNECT CAR BATTERY INSTALLATION OF SIREN UNDER BONNET - + INSTALLATION OF ULTRASONIC VOLUME PROTECTION B B B A 80°C A A H2O CONNECTIONS GENERAL WIRING DIAGRAM CONNECTION OF ELECTRONIC EMERGENCY KEY (OPT) CONNECTION OF KEY 4 KEYPAD (OPT) GREY (cannot be used if KEY 4 KEYPAD is connected) ANTENNA LEAVE LOOSE (DO NOT TIE DOWN) GREY RED Key 4 BATTERY POSITIVE (+30) ANTENNA LEAVE LOOSE (DO NOT TIE DOWN) RECEPTACLE FOR EMERGENCY KEY (OPT) KEYPAD K
PERIPHERAL PROTECTION – BONNET * PERIPHERAL PROTECTION – DOORS * 12 PERIPHERAL PROTECTION – BOOT * 24 + 30 MOUNT A SWITCH FOR BONNET PROTECTION GREEN INTERNAL BOOT LIGHT PURPLE M134 DIODE MODULE OR (X4) 1N4002 DIODES 1 13 ORIGINAL BOOT SWITCH INSERT IN PIN. 13 ORIGINAL DOOR SWITCHES + PURPLE SIREN FOR H.P.A. 4.0 SIREN FOR H.P.A. 2.5 -3.5 24 12 M02 SC1 24 12 CONNECTOR OF CABLE FOR H.P.A. CONTROL UNIT CONNECTOR OF CABLE FOR H.P.A. CONTROL UNIT INSERT IN PIN.2 INSERT IN PIN.
CUSTOMISING THE OPERATING FUNCTIONS The installed alarm system has a series of preset factory settings, which can be modified according according to the vehicle that the alarm system is to be installed on as well as the owner’s preferences. The factory settings and their possible customisations are illustrated in the table below.
DESCRIPTION OF THE OPERATING FUNCTIONS 1 - BUZZER - Factory Setting: disabled The acoustic signal provided by the siren when the alarm system is armed and disarmed. Its use is not permitted in countries in the European Community. 2 - CONTROL OF HORN/SIREN - Factory Setting: alternating Negative signal (1A max) to control the horn or additional siren during an alarm cycle. Select alternating to control a horn, continuous to control a siren.
ANTI CARJACKING FUNCTION Only one anti carjacking method mode can be enabled at a time: when one method is enabled the other two are automatically neutralised. If the brake pedal has been enabled in the Safety Lock function (see Function 3), the activation of INTENTIONAL ANTI CARJACKING mode and AUTOMATIC ANTICARJACKING 2 is also neutralised. 14 - INTENTIONAL ANTI CARJACKING FUNCTION - Factory Setting: disabled Conditions a, b and c must be met if this function is required.
COMPLETE ENGINE IMMOBILISATION 60 sec after the instrument panel has been turned off (+15 OFF), it will no longer be possible to start the engine up again. If the correct password is keyed in when the instrument panel is on (+15 ON), this function is neutralised. The system can also be neutralised using the RESTORING THE OVERRIDE CODE procedure (refer to relative section).
THE OVERRIDE CODE In emergency situations, the alarm system can be neutralized by means of the OVERRIDE code. This is keyed in by using the button on the SWITCH/LED mounted on the dashboard or via the KEY4 keypad, if present. The code set during production in the factory is the same for all control units, i.e. 1 1 1 1 1 or 1111 if the keypad is enabled.
CUSTOMISING THE OVERRIDE CODE WITH KEYPAD 1 Beep of siren WITHIN 10 SEC ARM THE ALARM BUTTON 1 X 4 TIMES WITHIN 10 SEC LED FLASHING QUICKLY ON OFF X4 WITHIN 10 SEC LED ON KEY IN 4 DIGITS OF CURRENT CODE WHITIN 10 SEC WRONG CODE 3 BEEPS CORRECT CODE 1 LONG BEEP WITHIN 10 SEC ON OFF LED FLASHES RAPIDLY 1 BEEP WITHIN 10 SEC WITHIN 10 SEC WITHIN 10 SEC WITHIN 10 SEC 3 BEEPS KEY IN CUSTOMISED CODE EG.
USE OF THE OVERRIDE CODE This procedure is only operational after the initial immunity time or after the anti carjacking protection has become operative. Alarm cycles will be triggered as the code is being keyed in. If the LED/SWITCH does not work, it is also possible to insert the code by turning the vehicle’s ignition key ON and OFF instead. When the alarm system is armed, or when the anti carjacking protection is operational, follow the procedure illustrated below to disarm the H.P.A. control unit.
REMOTE CONTROLS The alarm control unit is supplied with 2 coded remote controls but it is possible to add extra remote controls, up to a maximum of 7 in all. To add new remote controls, they must first of all be ordered from your local MetaSystem Customer Care Centre; you must indicate the base code, located on the red card supplied with the product, on your order. After you receive the remote controls, they have to be linked up to the control unit by means of the dedicated link-up procedure.
If the keypad has been mounted, press 2 any keys at the same time and press button A on the remote control to transmit a signal: the keypad will produce 4 BEEPs to confirm reception. Release the 2 buttons and key in the override code within 10 sec: the direction indicators flash 2 times and the siren produces 2 BEEPs to confirm the function has been activated.
BUTTON B can also be activated when control unit is disarmed *PANIC: can be activated when control unit is armed, after initial immunity time, max duration 10 sec., can be interrupted by pressing same button FLASHING 1 FLASH 2 FLASHES * PASSIVE ARMING OF ENGINE IMMOBILISER: arms 4 minutes after the engine is turned off, or 50 sec. after a door is opened (with engine off). * PASSIVE ARMING OF ALARM + IMMOBILISER: arms 60 sec. after opening and closing a door (with engine off).
www.metasystem.it MetaSystem S.p.A. • Via Oberdan 42100 Reggio Emilia • ITALY Tel. +39-0522 364 111 • Fax +39-0522 364 150 info@metasystem.it Data and technical features may be changed without notice. V808910C C Copyright by MetaSystem 12/2001 GRAFITALIA (RE).