User Manual

ManualsBrandsProbuilt Professional Lighting ManualsLightingWobblelight

Manufactured by ProBuilt Professional Lighting: 877-707-0800

Thank you for purchasing Wobblelight

IMPORTANT SAFETY INSTRUCTIONS

WARNING !!!

READ AND UNDERSTAND ALL INSTRUCTIONS

Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

SAVE THESE INSTRUCTIONS

This manual contains important safety and operating instructions for Wobblelight

portable job site lighting. Before using Wobblelight

, please review all of the

following safety instructions carefully and read all labels on the Wobblelight

unit.

INSTRUCTIONS PERTAINING TO THE RISK OF FIRE, ELECTRIC SHOCK, EXPOSURE TO UV RADIATION AND INJURY TO PERSONS:

WARNING: To reduce the risk of fire, electric shock, exposure to excessive UV radiation or injury to persons:

 DO NOT connect Wobblelight

to power source until the bulb is installed and the unit is completely assembled.

 Metal halide and halogen bulbs get EXTREMELY HOT immediately upon illumination and can cause burns.

 Bulbs stay hot for an extended period of time after Wobblelight

unit has been turned off, and can continue to cause burns.

 DO NOT attempt to remove the protective lens to change bulbs unless the Wobblelight

unit is disconnected from the power source and the bulb has

completely cooled.

 Not for use in wet locations. DO NOT use Wobblelight

where this is potential for exposure to excessive moisture from rain, snow, ice or water spray or

standing water.

 DO NOT leave Wobblelight

units operating for extended periods of time in unattended areas.

 Connect Wobblelight

only to 120 volt, 60 Hz power source which is protected with a ground-fault circuit interrupter (GFCI) and over-current protection.

Any other connection voids warranty.

 Wobblelight

is not recommended for use with generators except under emergency situations or when the generator output power is carefully monitored to

stay within +/-10% of 120V.

 Keep away from flammable materials.

 Wobblelight

must be operated in the upright position only. DO NOT mount Wobblelight

units upside down or restrain them such that they lay on their

side.

 Use only approved extension cords in good condition and of the appropriate type, gauge and length for each application.

Summary of content (7 pages)

PAGE 1
Manufactured by ProBuilt Professional Lighting: 877-707-0800 Thank you for purchasing Wobblelight® IMPORTANT SAFETY INSTRUCTIONS WARNING !!! READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions for Wobblelight® portable job site lighting.
PAGE 2
        Keep extensions cords dry and use ground fault circuit interrupter (GCFI) devices in accordance with all applicable electrical code requirements. DO NOT operate Wobblelight® units with the protective dome and cap missing or broken. DO NOT use Wobblelight® units with a broken housing or damaged electrical receptacles. Take any damaged units out of service immediately. Replacement parts and/or repair services are available from Wobblelight® or a local authorized service center.
PAGE 3
  IV. Sylvania Metalarc® M175/U/ET18, Eiko ArcMaster® MH175/U/ED28 Sylvania Metalarc® M400/U/ET18, Eiko ArcMaster® MH400/U/ED28 LAMP INSTALLATION Disconnect Wobblelight® from power source and turn off switch. Allow dome and lamp to cool completely. Remove the Wobblelight® dome / cap assembly by removing the five mounting screws. Screw lamp firmly but not forcibly into socket in order to avoid breakage. Tighten bulb until it is secure in the socket – do not over tighten.
PAGE 4
     Although the halogen lamp inner capsule may continue to operate if the outer bulb is broken or damaged, discontinue use immediately and replace with a new lamp. The inner halogen lamp generates ultraviolet radiation which can cause skin and eye irritation with prolonged exposure. Never expose an operating lamp to moisture such as rain, sleet or snow. Avoid excessive bumping and bouncing during operation since mechanical shock can cause shattering and failure of the halogen lamp.
PAGE 5
. 6. 7. Reinstall the Wobblelight® dome / cap assembly by aligning the five mounting holes with the five mounting nuts (note that the dome handle should be aligned with the power switch). Secure dome with the five mounting screws – do not over tighten. ® Your assembled Wobblelight is now ready for use. USE OF Wobblelight® By following the safety and operating instructions in this manual, your Wobblelight® should endure normal abuse and last trouble-free for years.
PAGE 6
CIRCUIT PROTECTION All Wobblelight® models are equipped with an externally re-settable circuit breaker located beneath the power switch. The breaker will trip when the total amperage load on Wobblelight® exceeds 12 amps. If the breaker trips, the lamp circuit and the accessory outlet will be immediately de-energized. The following steps should be taken in the event of a circuit breaker trip: 1.
PAGE 7
EXCLUSIONS. This warranty does not cover: • • • • • • • • • • Bulbs Physical damage to plastic components including (but not limited to) domes, caps and housings and inlet / outlet plugs. Damages or repairs of any kind to any products, items or personal or other property resulting from use of the Wobblelight® product. Damages or repairs of any kind to any products, items or personal or other property caused by accidents, abuse or misapplication of the Wobblelight® product.