Installation Manual

ManualsBrandsPro1 Technologies ManualsElectronicsPro1 Wireless Thermostat

T731W(O)

Installation Manual

Pro1 Technologies

Toll Free : 888-776-1427

Web: www.pro1iaq.com

Hours of Operation: M-F 9AM - 6PM Eastern

Thermostat Application Guide

Description

Gas or Oil Heat

Electric Furnace

Heat Pump (No Aux. or Emergency Heat)

Heat Pump (With Electric Aux.)

Multi-Stage Systems

Heat Only Systems - Floor or Wall Furnace

Cool Only Systems

Millivolt

Yes

Power Type

Battery Power

Hardwire (Common Wire)

Hardwire (Common Wire) with

Battery Backup

Table of Contents

Installation Tips

Thermostat Quick Reference

Wiring

Technician Setup

Establishing Communication

Network Specications

Specications

Page

A trained, experienced

technician must install this

product.

Carefully read these

instructions. You could damage

this product or cause a

hazardous condition if you fail

to follow these instructions.

Una version en español de este

manual se puede descargar en

la pagina web de la compañia.

Rev. 1950

Mount Thermostat

Align the 4 tabs on the subbase

with corresponding slots on the

back of the thermostat, then push

gently until the thermostat snaps

in place.

Battery Installation

Battery installation is

optional if thermostat is

hardwired (R and C terminal

connected to 24V power).

Important:

High quality alkaline batteries are recommended.

Rechargeable batteries or low quality batteries

do not guarantee a 1-year life span.

Insert 2 AA

Alkaline batteries

(included). High

quality alkaline

batteries are

recommended.

Installation Tips

4-5

6-11

12-16

2-3

Installation Tips Thermostat Quick Reference

Getting to know your thermostat

Subbase Installation

The thermostat should be installed approximately 4 to 5 feet above the

oor. Select an area with average temperature and good air circulation.

• Close to hot or cold air ducts

• That are in direct sunlight

• With an outside wall behind

the thermostat

• In areas that do not require

conditioning

• Where there are dead spots

or drafts

(in corners or behind doors)

• Where there might be

concealed chimneys or

pipes

Wall Locations

Vertical Mount

Horizontal Mount

For vertical mount put one screw on the top

and one screw on the bottom.

For horizontal mount put one screw on the

left and one screw on the right.

All of our products are mercury free.

However, if the product you are

replacing contains mercury, dispose of

it properly. Your local waste

management authority can give you

instructions on recycling and proper

disposal.

Pick an installation location that is easy for

the user to access. The temperature of the

location should be representative of the

building.

Installation Tip

Mercury Notice

Do not install

thermostat in locations:

Failure to disconnect the power before

beginning to install this product can

cause electrical shock or equipment

damage.

Installation Tip:

Electrical Hazard

U.S. Registered Trademark. Patents pending

Heat Pump (With Gas Aux.)

Emergency Heat

Conventional Single Stage Furnace

Geothermal

High and Low Fan Speed

Yes

Located on the back of thermostat.

P.O. Box 3377

Springeld, MO 65808-3377

Glow in the Dark Light Button

Setpoint Buttons

LCD

System Button

Fan Button

17-18

Summary of content (5 pages)

PAGE 1
Installation Manual Installation Tips T731W(O) Pro1 Technologies Wall Locations The thermostat should be installed approximately 4 to 5 feet above the floor. Select an area with average temperature and good air circulation. Do not install thermostat in locations: P.O.
PAGE 2
Wiring Thermostat Quick Reference 3 COOL ON Set At HEAT ON FAN ON STAGE 1+2 1 Caution: Electrical Hazard Failure to disconnect the power before beginning to install this product can cause electrical shock or equipment damage. Wiring 2 On LHM AutoPrev Heat NextCool 1 Indicates the current room temperature 2 Low Battery Indicator: Replace batteries when this indicator is shown. 3 System Operation Indicators: COOL ON, HEAT ON or FAN ON will display when the COOL, HEAT, or FAN is on.
PAGE 3
Wiring Wiring Base Module - PTAC Installation When Working With A Vertical Unit Range between the thermostat and the base module is up to 100 feet with no obstructions and up to 50 feet through standard building materials. To optimize the range try placing the base module with no metal between it and the thermostat. 1. Do not mount Module inside the cabinet of the unit, or in a metal enclosure. 2. Mount on the outside of the unit to maximize wireless communication.
PAGE 4
Technician Setup Tech Setup Steps Fan Operation Fan Speeds Select Gas (GS) for applications where the air handlers controls the fan during a call for heat. Slect Electric (EL) if you would like the thermostat to control the fan during a call for heat. Select number of fan stages you would like the thermostat to operate. the terminal you would Medium Select like to use to operate the medium Speed Fan speed fan.
PAGE 5
Technician Setup Technician Setup Occupancy Models Only Tech Setup Steps Local Occupancy Sensor Duration of Occupancy (Only displayed if Local Occupancy Sensor is ON) LCD Will Show Adjustment Options 0F When the occupancy sensor is turned on you have the ability to set how long the thermostat will go into occupancy mode everytime a person is sensed. (Only displayed if Local Occupancy Sensor is ON) 8 75 (Only displayed if Local Occupancy Sensor is ON) is being occupied.