SDS

ManualsBrandsPro Products ManualsAppliance CleanersPro Easy 1 oz. Feeder Starter Kit Cleaner (6-Pack)

SAFETY DATA SHEET

1. Identification

PRO ResCare™Product identifier

Not available.

Other means of identification

Water Softener Resin Cleaner

Recommended use

None known.

Recommended restrictions

Manufacturer/Importer/Supplier/Distributor information

Manufacturer

Pro Products LLC

Address

Suite 200

6714 Pointe Inverness Way

Company name

46804-7935

Telephone

260-483-2519

Emergency phone number

1-800-424-9300 (CHEMTREC)

E-mail

United States

Not available.

Fort Wayne

See above.

Supplier

2. Hazard identification

Category 1Corrosive to metals

Physical hazards

Category 1Skin corrosion/irritation

Health hazards

Category 1Serious eye damage/eye irritation

Not classified.

Environmental hazards

Not classified

WHMIS 2015 defined hazards

Label elements

Signal word

Danger

Hazard statement

May be corrosive to metals. Causes severe skin burns and eye damage.

Precautionary statement

Prevention

Keep only in original packaging. Do not breathe mist or vapor. Wash thoroughly after handling.

Wear protective gloves, protective clothing, eye protection and face protection.

Response

Absorb spillage to prevent material-damage.

IF SWALLOWED: Rinse mouth. Do NOT induce vomiting. IF ON SKIN (or hair): Take off

immediately all contaminated clothing. Rinse skin with water or shower. Wash contaminated

clothing before reuse. IF INHALED: Remove person to fresh air and keep comfortable for

breathing. Immediately call a POISON CENTER or doctor. Specific treatment (see information on

this label). IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses,

if present and easy to do. Continue rinsing.

Storage

Store locked up. Store in a corrosion resistant container with a resistant inner liner.

Disposal

Dispose of container in accordance with local, regional, national and international regulations.

None known

WHMIS 2015: Health Hazard(s)

not otherwise classified

(HHNOC)

None known

WHMIS 2015: Physical

Hazard(s) not otherwise

classified (PHNOC)

Hazard(s) not otherwise

classified (HNOC)

None known.

Supplemental information

Not applicable.

#13207 Issue date 05-October-2020

Page: 1 of 9

Summary of content (9 pages)

PAGE 1
SAFETY DATA SHEET 1. Identification Product identifier PRO ResCare™ Other means of identification Not available. Recommended use Water Softener Resin Cleaner Recommended restrictions None known. Manufacturer/Importer/Supplier/Distributor information Manufacturer Telephone E-mail Emergency phone number Pro Products LLC 6714 Pointe Inverness Way Suite 200 Fort Wayne IN 46804-7935 United States 260-483-2519 Not available. 1-800-424-9300 (CHEMTREC) Supplier See above. Company name Address 2.
PAGE 2
3. Composition/Information on ingredients Mixture CAS number % Alkyl benzyl dimethyl ammonium chloride Chemical name Common name and synonyms 68424-85-1 0.1-1* Phosphoric acid 7664-38-2 10-30* All concentrations are in percent by weight unless ingredient is a gas. Gas concentrations are in percent by volume. US GHS: The exact percentage (concentration) of composition has been withheld as a trade Composition comments secret in accordance with paragraph (i) of §1910.1200.
PAGE 3
Methods and materials for containment and cleaning up Stop leak if you can do so without risk. Should not be released into the environment. Prevent entry into waterways, sewer, basements or confined areas. Large Spills: Dike the spilled material, where this is possible. Cover with plastic sheet to prevent spreading. Absorb spillage to prevent material damage. Use a non-combustible material like vermiculite, sand or earth to soak up the product and place into a container for later disposal.
PAGE 4
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000) Components Type Phosphoric acid (CAS 7664-38-2) US. ACGIH Threshold Limit Values Components Phosphoric acid (CAS 7664-38-2) PEL 1 mg/m3 Type Value STEL 3 mg/m3 TWA 1 mg/m3 US. NIOSH: Pocket Guide to Chemical Hazards Components Type Phosphoric acid (CAS 7664-38-2) Value Value STEL 3 mg/m3 TWA 1 mg/m3 Biological limit values No biological exposure limits noted for the ingredient(s).
PAGE 5
Explosive limit - lower (%) Not available. Explosive limit - upper (%) Not available. Vapor pressure Not available Vapor density Not available Relative density 1.10 - 1.11 Solubility(ies) Not available. Auto-ignition temperature Not available Decomposition temperature Not available. Viscosity Not available. Other information Explosive properties Not explosive. Oxidizing properties Not oxidizing. 10.
PAGE 6
Exposure minutes Not available. Erythema value Not available. Oedema value Not available. Causes serious eye damage. Serious eye damage/eye irritation Corneal opacity value Not available. Iris lesion value Not available. Conjunctival reddening value Not available. Conjunctival oedema value Not available. Recover days Not available.
PAGE 7
Hazardous waste code Waste from residues / unused products Contaminated packaging D002: Waste Corrosive material [pH <=2 or =>12.5, or corrosive to steel] The waste code should be assigned in discussion between the user, the producer and the waste disposal company. Dispose of in accordance with local regulations. Empty containers or liners may retain some product residues. This material and its container must be disposed of in a safe manner (see: Disposal instructions).
PAGE 8
WHMIS 2015 Exemptions Not applicable US federal regulations This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication Standard, 29 CFR 1910.1200. TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D) Not regulated. CERCLA Hazardous Substance List (40 CFR 302.4) Phosphoric acid (CAS 7664-38-2) Listed. SARA 304 Emergency release notification Not regulated. OSHA Specifically Regulated Substances (29 CFR 1910.1001-1052) Not listed.
PAGE 9
16. Other information LEGEND HEALTH / 3 0 Severe Serious Moderate Slight Minimal Disclaimer Issue date Version # 4 3 2 1 0 FLAMMABILITY 0 PHYSICAL HAZARD 0 PERSONAL PROTECTION X 3 0 The data contained in this material safety data sheet was obtained from sources that were technically accurate, reliable, and state of the art when this document was prepared. If data was unavailable to complete certain sections, the absence of that data is identified in this document.