INSTRUCTIONS FOR USE Pro-Ject Jukebox S2
© Pro-Ject Audio Systems · Pro-Ject Jukebox S2 · Revision 22.04.
Jukebox S2 Controls, features and connections (1) TURNTABLE MOTOR SWITCH (2) AMPLIFIER ON/OFF SWITCH (3) REMOTE CONTROL (4) INPUT SELECTOR, VOLUME CONTROL (5) PLATTER (6) DRIVE BELT (7) STEPPED DRIVE PULLEY (8) TONEARM COUNTERWEIGHT (9) TONEARM TUBE (10) TONEARM REST AND REMOVABLE TRANSPORT LOCK (11) TONEARM LIFT LEVER (12) HEADSHELL WITH FINGER LIFT (13) TURNTABLE DISPLAY (14) EARTH CONNECTION (15) PHONO OUT (16) LINE IN (17) VAR OUT (18) FIX OUT (19) BT ANTENE (20) S
! Warning of a hazard for the user, the unit or possible misuse Important notice The following instructions for adjusting the cartridge are provided in case the cartridge is replaced by a different model at a later date. During assembly and adjustment of the deck small parts could be lost if not carefully placed in a suitable receptacle. Before starting assembly make get fwqmiliar with the parts listed above and correspondingly numbered in the technical drawings above.
level position. Moving the counterweight away from the cartridge will reduce pressure and towards will increase pressure. Finally secure the counterweight using hexagonal key provided. If the stylus gauge becomes level, then the correct pressure has been achieved. However if the there is insufficient or excessive pressure the gauge will either not move or tilt down. Connectors ! Take care to connect the left and right channels correctly.
Switching ON and OFF (turntable motor) The rocker switch (1) on the bottom turns the motor of the turntable To switch on from standby or to standby (amplifier) The rocker switch (2) on the bottom turns the unit on or back into standby. Control of the unit using the knob on the front Standby After the unit is powered on by the rocker switches on the bottom, pressing the knob for 3 seconds, turns the unit on.
Bass+/Bass-/Treble+/Treble- tone control Loudness activate/deactivate Loudness BT/Turntable/Line in direct access to input Volume+/Volume- adjust volume BT connection BT is active only when BT input is selected. Juke Box E remembers last paired unit and reconnects automatically when available and if the BT device allows automatic reconnections. Juke Box E doesn´t request any pairing code confirmation. Only one active BT connection is possible at a time.
** All cartridges with half inch mounting holes can be fitted. Leaving the needle's protection cover on, fit the cartridge to the headshell (12) using the screws supplied with the cartridge by passing one screw through each slot in the headshell (12). Do not tighten the nuts yet. Connect the tonearm wires to the cartridge pins as follows: white left channel positive (L+) red right channel pos.
Outboard power supply Dimensions (W x H x D) Weight Dimensions packaging (W x H x D) Weight incl. packaging 24V/4A DC 415 x 118 x 334mm 5,0kg 488 x 235 x 393mm 7kg Potential incorrect use and fault conditions Pro-Ject turntables are manufactured to the highest standards and undergo strict quality controls before leaving the factory. Faults that may possibly occur are not necessarily due to material or production faults but can sometimes be caused by incorrect use or unfortunate circumstances.
Warranty The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use and/or by transportation without the original packaging. Modification or change to any part of the product by unauthorized persons, release the manufacturer from any liability over and above the lawful rights of the customer. Pro-Ject Audio Systems is a Registered Trademark of H. Lichtenegger. This guide was produced by: Pro-Ject Audio Systems Copyright © 2018. All rights reserved.
© Pro-Ject Audio Systems · Pro-Ject Jukebox S2 · Revision 22.04.
