INSTRUCTIONS FOR USE E1 / Phono / BT
Dear Music Lover, Thank you for choosing Pro-Ject Audio Systems record player. Your E1 turntable has been handcrafted and rigorously tested by skilled technicians to give you years of enjoyable, trouble free service. Please contact your dealer if you require additional assistance. Important: Your turntable was shipped partially disassembled in order to avoid damage to sensitive parts. Please check immediately to make sure that neither the packaging nor the device was damaged in transit.
GENERAL INFORMATIONS Controls, features and connections 1 PLATTER & FELT MAT 2 CHASSIS 3 MOTOR WITH PULLEY 4 SUB – PLATTER 5 DRIVE BELT 6 TONEARM COUNTERWEIGHT 7 TONEARM LIFT LEVER 8 TONEARM REST / REMOVABLE TRANSPORT LOCK 9 TONEARM TUBE 10 HEADSHELL WITH FINGER LIFT AND PRE-MOUNTED ORTOFON CARTRIDGE 14 LID 13 LID HINGES 14 HINGE FASTENERS 15 POWER SUPPLY SOCKET 16 ON / OFF SWITCH, SPEED SELECTOR Accessories 1 SINGLE ADAPTOR 2 ALLEN KEY 2mm 3 COUNTERWEIGHT no.
© Pro-Ject Audio Systems · Pro-Ject E1 / Phono / BT · Revision 2022.04.
SETUP 1. Platter and drive belt installation Please remove drive belt from accessories box and install it as shown in the following ilustration. Put the felt mat on the top of the platter. 2. Cartridge installation, stylus exchange * If you purchased this turntable in a package that included the cartridge, this has already been done for you. Install the cartridge into the headshell, using the appropriate hardware included with your cartridge. All cartridges with half inch mounting holes can be fitted.
3. Vertical Tracking Force setting (VTF) * This setting is only neccessary when you decided to repalce your cartridge. For factory fitted cartridge, VTF was perfectly pre-set already. Before setting the Vertical Tracking Force, confirm the exact weight of your cartridge. Pushing carefully, move the counterweight onto the rear end of the counterweight support rod. Place the stylus pressure gauge onto the platter.
5. Maintenance and cleaning Your record player requires little or no regular maintenance. Remove dust with a slightly moistened antistatic cloth. Never use a dry cloth because this will create static electricity which attract more dust! Antistatic cleaning fluids are available at specialist stores but must be applied sparingly to avoid damage to rubber parts. It is recommended to fit the needle cover before cleaning or maintenance is carried out to avoid damage.
E1 Phono SPECIFIC INFORMATIONS Controls, features and connections 1 PHONO/LINE OUTPUT, EARTH CONNECTION 2 PHONO/LINE OUTPUT SWITCH 3 POWER SUPPLY SOCKET _____________________________________________________________________________________________________________ Connection to the amplifier The record player has gold plated female RCA phono sockets and possibility to choose between Phono and LINE output.
E1 BT SPECIFIC INFORMATIONS Controls, features and connections 1 PHONO/LINE OUTPUT, EARTH CONNECTION 2 BLUETOOTH SWITCH _____________________________________________________________________________________________________________ Connection to the amplifier The record player has two possible outputs – Line OUT with integrated preamplifier and Phono OUT for connection to the preamplifier. If you choose Phono OUT, then use the Phono input (sometimes labelled gram, disc or RIAA) on your amplifier.
Technical specifications Pro-Ject E1 / Pro-Ject 8.6 Nominal speeds Speed variance Wow and flutter Signal to noise Effective tonearm mass Effective tonearm length Overhang Power consumption Outboard power supply Dimensions (W x H x D) Weight Dimensions packaging (W x H x D) Weight incl. packaging 33/45 r.p.m. 33: ±0.70% 45: ±0.60% 33: ±0.25% 45: ±0.23% -65dB 7.0g 8.6" (218.5mm) 22,0mm 4.5W 15V / 0 – 0.8A DC (set at 0.5A), universal power supply 420 x 112 x 330mm, with open dustcover 420 x 370 x 393mm 3.
Potential incorrect use and fault conditions Pro-Ject turntables are manufactured to the highest standards and undergo strict quality controls before leaving the factory. Faults that may possibly occur are not necessarily due to material or production faults but can sometimes be caused by incorrect use or unfortunate circumstances. Therefore the following list of common fault symptoms is included. The platter doesn't turn although the unit is switched on: The unit is not connected to the mains power supply.
© Pro-Ject Audio Systems · Pro-Ject E1 / Phono / BT · Revision 2022.04.