Primex ClassicSync OneVue 1 Watt Transceiver with Internal Antenna D R AF T Install Guide ©2019 Primex. All Rights Reserved. The Primex logo is a registered trademark of Primex. All other trademarks are the property of their respective owners. 4/3/2019. Primex, Inc. | 965 Wells Street | Lake Geneva, WI 53147 | www.primexinc.
Legal Notice Copyright ©2019 Primex, Inc. All rights reserved. Printed in the USA. Information in this document is subject to change without notice. Software described in this document is furnished under a license agreement or nondisclosure agreement. The software may be used or copied only in accordance with the terms of those agreements.
Regulatory Compliance Federal Communications Commission (FCC) / Industry Canada (IC) Primex OneVue Transceiver TX400 License Requirements l Operation of the Transceiver requires a FCC/IC operating license, which must be obtained prior to operation. l FCC licenses must be renewed every 10 years and the IC licenses must be renewed annually. l l As a service, Primex will file the license application if the end-user desires it.
Radio Standards Specification (RSS) This device complies with Industry Canada licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Important Safety Instructions READ ALL INSTRUCTIONS BEFORE INSTALLATION, OPERATION, OR MAINTENANCE OF PRODUCT. Safety Instructions Some of the following information may not apply to your particular product model; however, as with any electronic product, precautions should be observed during installation, operation, and maintenance. l Never operate the Transceiver without the antenna being properly connected to the Transceiver.
Overview of the Primex ClassicSync Solution Architecture 7 Time synchronization 7 Transceiver power-up sequence 7 Transceiver power failure 8 Specifications Specifications: OneVue 1 Watt Transceiver Specifications: GPS Receiver AF T Install 1 Watt Transceiver with Internal Antenna 9 9 11 12 12 Tools and equipment required 12 Install location guidelines 12 Step 1: Install GPS Receiver 13 Step 2: Establish Transceiver connections and apply power 14 R Configuration requirements Step 3: C
Overview of the Primex ClassicSync Solution Learn how the solution works and how the system devices provide synchronized time. Architecture The Primex ClassicSync solution provides synchronized time using our 72-73 MHz unique broadcast frequency to transmit a wireless signal to all system devices. The frequency allows the system wireless signal to broadcast through common building materials and across longer distances with less potential for signal interference.
5. If the RTC clock is off significantly, the Transceiver it enters a critical error state, its front panel LED Error status indicator is illuminated, and transmits its state to OneVue at its scheduled check-in. Only occurs after the first 30 minutes of operation if the RTC continues to be significantly off. Transceiver power failure During a power failure, the Transceiver continues to track time with the last valid time signal that it received.
Specifications Primex OneVue Transmitters use a 72-73 MHz broadcast frequency to transmit a wireless radio frequency to seamlessly synchronize every clock and independently to display the exact same time. Leveraging the precision of GPS satellite or Network Time Protocol (NTP) time, the Transmitters wirelessly synchronize time with Primex 72-73 MHz analog and digital clocks, timers and other receivers throughout a facility.
Parameter User-defined Specification Legacy Clock Time Zone, Alarm Delay, Firmware, Unresponsive Timeout, and Check-in Interval. settings (OneVue Sync software) Front Panel Four LED status indicators (Power, Transmit, Caution, Error) and Bluetooth labeled push-button to pair Transceiver with the Primex OneVue Device Configurator (ODC) app. Rear Panel Network LAN port (RJ-45 Ethernet, 100/10 Mbps, 802.
Specifications: GPS Receiver A GPS Receiver draws time information from the U.S. Government Satellites, providing the system with Coordinated Universal Time (UTC). l Mounted to rooftop, pole, or window (not a Low-E glass window). l GPS Receiver sends UTC time to the Transceiver via the NMEA 0183 standard protocol. Optional GPS extension cable. A specially designed low-resistance cable to extend the distance between GPS Receiver and Transceiver. The maximum total length of the cable cannot exceed 200 ft.
Install 1 Watt Transceiver with Internal Antenna This topic provides the requirements and procedures to install a Transceiver with an internal antenna. Configuration requirements OneVue Transmitters are required to be configured for operation with the Primex OneVue Device Configurator (ODC) app. A Transceiver can be configured for use with the Primex OneVue Sync solution or as a standalone Transceiver.
Transceiver must be located in a controlled environment that is 32° to 122° F (0° to 50° C) and non-condensing humidity environment. l Step 1: Install GPS Receiver A GPS Receiver is required when a Transceiver is set to use GPS as its time source. GPS Receiver kit components Part Quantity 1 GPS 18 LVC and connector 1 M3 x 0.5 x 6 mm pan head screws 2 #6 x 3/8 sheet metal screw 3 Suction cups 3 AF T Mounting bracket U-bolt with nuts for mounting on 1 in. (2.
NOTE Be sure to follow local building code requirements when attaching the GPS unit to the inside of a window. Clean the AF T windowpane before using the suction cups for attachment. 4. Route GPS cable and connect to Transceiver GPS connection. Step 2: Establish Transceiver connections and apply power D R Internal antenna connection is located on its top panel and its back panel connections include power, GPS, and Ethernet. 1.
Step 3: Configure Transceiver settings with OneVue Device Configurator (ODC) app 1. Open the ODC app. 2. Select an option: Connect to OneVue or Standalone Configuration. AF T 3. If Connect to OneVue selected, enter OneVue username and password. Bluetooth wireless signal. R 4. From the front of the Transceiver, press and release the Bluetooth pairing button. The Transceiver begins broadcasting its configured. D 5.
7. Select Continue. AF T 8. Enter Name of the Transceiver. The name commonly identifies its install location and type of Transceiver (main or repeater). 9. Verify Call Sign. R Call Sign displayed: Verify the Call Sign is the same as the supplied FCC/IC Information Form. If not correct, update. Call Sign not displayed: Enter the Call Sign located on the supplied FCC/IC Information Form. A Transceiver will not transmit (broadcast) without a valid Call Sign. D 10.
Repeater Transmit: Off 14. Channel section settings for a Repeater Transceiver only. Set the below two settings. Channel (receive): Required to be set to the Channel number of the Main Transceiver. If multiple Repeater Transmitters onsite, set to the Channel number of a Repeater Transceiver in closest proximity with highest signal strength. Repeater Transmit (broadcast): Required to be set to the Channel number located on the FCC/IC Information Form. R AF T 15. Select Save. D 16.
LED LED Indicator Color Transmit Green Operating State/Status Main Transceiver: Solid green indicates transmitting (broadcasting). Repeater Transceiver: Solid green indicates transmitting (broadcasting) and flashing green indicates receiving signal from configured Repeater Transmit channel. Caution Error Yellow Red When illuminated, indicates in a warning/caution state, due to one or more of the status conditions below.
Technical Support You may require technical support when you have questions about product features, system configuration, or troubleshooting. Support services are delivered in accordance with your organization's support agreement, end user licenses agreements, and warranties, either with a Primex Certified Sales and Service Partner or directly with Primex. Support through Primex Certified Sales and Service Partners Ensuring our customers experience excellent service is of utmost importance to Primex.
Five Year Limited Warranty Primex, Inc. warrants this product to be free from defects in materials and workmanship for a standard of five (5) years from the date of purchase*. All product accessories, including external antennas and kit components, wireless tone generator, wireless data receiver, and UPS backup, are warranted for a period of one (1) year against material or manufacturing defects from the date of purchase. Primex, Inc.
