Smart-Sync™ Personal Series LCD Clock Install Guide OneVue Synchronized Time Solution Copyright © 2017 by Bluetooth SIG, Inc. The Bluetooth word mark and logos are owned by Bluetooth SIG, Inc. Other third-party brands and names are the property of their respective owners. OneVue is a trademark of Primex. The innovative technology software solution for facility and time synchronization monitoring and reporting. All other trademarks are the property of their respective owners. ©2017 Primex.
Legal Notice Copyright ©2017 Primex. All rights reserved. Printed in the USA. Information in this document is subject to change without notice. The software described in this document is furnished under a license agreement or nondisclosure agreement. The software may be used or copied only in accordance with the terms of those agreements.
About this Guide Audience This guide is intended for users tasked with installing Smart-Sync Personal Series LCD Clock Install Guide for use with the Primex OneVue Synchronized Time solution. Content messaging This guide includes notes, cautions, and warnings content that highlights important messages. Typeface Indicates Note Indicates something important or useful. Caution Indicates a command or procedure may have an unwanted or undesirable result.
Important Safety Instructions READ ALL INSTRUCTIONS BEFORE INSTALLATION, OPERATION, OR MAINTENANCE OF PRODUCT. Some of the following information may not apply to your particular product model; however, as with any electronic product, precautions should be observed during installation, operation, and maintenance. l Installation must conform to state or local building codes and ordinances. l Installation or maintenance should be performed only by qualified personnel as defined in the Local Electrical Code.
Regulatory Approvals FCC Compliance Pursuant to FCC 15.21 of the FCC rules, changes not expressly approved by Primex might cause harmful interference and void the FCC authorization to operate this product. FCC Radio Frequency Interference This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Radio Standards Specification (RSS) This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
European Union Declaration of Conformity and Restrictions Hereby, Primex Inc. declares that this equipment: Primex Synchronous Network System SNS4Z200 Personal Series LCD Clock complies with the essential requirements and other relevant provisions of Directive 1999/5/EC. This equipment is marked with and can be used throughout the European community.
CONTENTS Specifications Install Smart-Sync™ Personal Series LCD Clock 9 12 Installation Requirements 13 Installation and Operation Overview 14 Wall Mount 17 Tabletop Use 18 Remove Clock from Clock-Lock Mount 19 Battery Maintenance 20 Troubleshooting - Personal Series LCD Clock How to Measure the Bluetooth Signal Strength at Installation Location Warranty Technical Support 21 22 23 24
Specifications Display operation Display settings and time zone are managed from OneVue Automatically adjusts for Daylight Saving Time (DST) Time mode setting: set to 12 hour or 24-hour Date format setting: set to Time & Date (month-day) or Time & Date (day-month), and option to show day of the week Dimensions Physical dimensions: 7.5 in. H (19.1 cm) x 11.5 in. W (29.2 cm) x 1.75 in. D (4.5 cm) Calendar display dimension: 3.81 in. H (9.7 cm) x 5.5 in W (14 cm) Time display screen dimension: 2.25 in. H (5.
Backlight operation A switch on the side of the clock sets the backlight to High, Low, or Off. High and Low sets the intensity of the backlight. When set to High or Low, an optical sensor on the top of the clock samples available light to determine whether to turn on the backlight. Note: Backlight use significantly reduces battery life. To extend battery life, turn the backlight to Off or Low.
Operational indicators The Personal Series LCD Clock features easy-to-read time, day of the week, and month-date display as well as two operational indicators.
Install Smart-Sync™ Personal Series LCD Clock Learn how to install and operate a Personal Series LCD Clock.
Installation Requirements Refer to the Important Safety Instructions before installing, operating or performing maintenance of clocks. Installation requirements A Smart-Sync Bridge or Smart-Sync Clock is within 80 feet (24.3 m) from a clock installation location. You can also measure the Bluetooth signal strength at an installation location to determine if the location has adequate Bluetooth signal strength.
Installation and Operation Overview Smart-Sync Clocks are designed to provide ease of installation - requiring no end user configuration, simply take-out-of the box and install. The only operation dependency is its connection to an available Smart-Sync Bluetooth Network. l A Smart-Sync Clock is equipped with a Bluetooth Low Energy (BLE) Wireless Technology radio component, that allows the clock to establish a wireless connection to a Smart-Sync Bluetooth Network.
Installation - Smart-Sync Clock Add a Clock mode Upon first-power up at its installation location, a Smart-Sync Clock enters Add-a Clock mode as described below. 1. Once powered on at its installation location, the clock continuously searches for an available Smart-Sync Bluetooth Network. It may take up to 15 minutes for a clock to authenticate and connect to an available Smart-Sync Bluetooth Network.
Post-Installation Smart-Sync Clock Operation Once a Smart-Sync Clock has authenticated and connected to a Smart-Sync Bluetooth Network, the clock operates as described below. 1. Once a day, at a system defined time, a Smart-Sync Bridge connects to your facility’s Ethernet or Wi-Fi network to receive UTC time from a NTP Server and check-in to OneVue to download Smart-Sync device setting updates. 2.
Wall Mount Depending on your security needs, you can choose among the two mounting options. How use the clock-lock mount for a secure, wall-mount installation The Clock-Lock feature is a specially designed hanger at the top center of the clock. The clock-lock is designed to prevent accidents if the clock is bumped and it may reduce theft by requiring a particular combination of moves to remove the clock. 1. Verify the installation requirements are met.
Tabletop Use The Personal Series LCD Clock has an easel stand located on the back of the clock. How to set up the tabletop easel of a personal series clock 1. Verify the installation requirements are met. For more information, see "Installation Requirements" on page 1. 2. To place the clock on a table or desk, simply unfold both sides of the easel stand.
Remove Clock from Clock-Lock Mount To remove a Personal Series LCD Clock from a clock-lock mount, follow the steps illustrated below.
Battery Maintenance The Personal Series LCD Clock indicates a low battery status by showing a low battery icon on the clock display. The battery condition is also transmitted to your OneVue account. During a low battery condition, the clock is set to a Warning state with a low battery status in your OneVue account. Battery use recommendations l Use only high quality Alkaline batteries l Always use fresh, superior-quality batteries, with an expiration date at least five years past the installation date.
Troubleshooting - Personal Series LCD Clock To identify and solve operating issues, view the common troubleshooting topics below. The display appears to be locked up and the time is visible, but the time is not updating This may be due to batteries were installed without allowing power to drain from the clock. Recommended action Remove the batteries and hold down the check-in button for 10 seconds. Wait another 10 seconds and reinsert the batteries.
How to Measure the Bluetooth Signal Strength at Installation Location To determine if a Smart-Sync device location has adequate signal strength, you can measure the Bluetooth signal strength at the installation location. Primex recommends using the nRF Connect for Mobile - allows you to scan and explore Bluetooth® low energy devices. nRF Connect for Mobile is available for iOS and Android™ devices and can be downloaded from the App Store or Google Play.
Warranty Two Year Limited Warranty Primex warrants this product to be free from defects in materials and workmanship for a standard of two (2) years from the date of purchase. Primex will at its sole option, repair or replace any components that fail in normal use. Such repairs or replacements will be made at no charge to the customer for replacement parts. The customer will be responsible for any transportation costs.
Technical Support You may require Technical Support when you have questions about product features, system configuration or troubleshooting. Support services are delivered in accordance with your organization's support agreement, end user licenses agreements, and warranties, either with a Primex Certified Sales and Service Partner or directly with Primex. Support through Primex Certified Sales and Service Partners Ensuring our customers experience excellent service is of utmost importance to Primex.