Video Sender Operation Manual
Table of Contents 1 Introduction............................................................................................................1 1.1 Features ..................................................................................................1 2 List of package contents.........................................................................................2 3 Outline....................................................................................................................
IMPORTANT This equipment has been tested and found to comply with the limits for a Consumer Equipment RF Lighting device,pursuant to Part ISC of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Safety Pre-caution To prevent fire or shock hazard, Do not expose this product to rain or moisture. Do not use near a bath tub, wash bowl, sink or laundry tub Do not use in a wet basement or in or around a swimming pool.
1 Introduction The new 2.4GHz system VF2RSP sends consistent, sharp audio and video images up to 100M to other rooms without running cable. The 2.4 GHz FM signal penetrates wall and avoids interference from other crowded 900 MHz band. Due to FM modulation, it provides a superior quality. With four channels, you could find optimal reception and transmit different sources using multiple pairs. The special hidden omni directional antenna maximizes the signal range. FCC,CE approved Easy installation. 1.
2 List of package contents The following devices should be included in the box.
3 Outline Model# VF2RSP 3 Video Sender Manual Version 5/2
Transmitter (VT2RSP) Front IR extender antenna Receives 433 remote control signals Power LED REAR Channel selection IR Mouse in DC12V in DC12V out VideoIn Audio Left in 4 Video Sender Manual Version 5/2 Audio Right in Power On/Off Switch
Receiver (VR2RSP) Front IR extender antenna Send 433 remote control signals Power LED Receives infrared signal from remoter controller REAR Channel selection DC12V in Video out Audio Left out Audio Right out 5 Video Sender Manual Version 5/2 Power On/Off Switch
Setting up units It takes only few minutes to set up Video Sender. You could connect most of audio/video source to transmitter and connect TV to receiver in another location. There is no wire needed between transmitter and receiver.
3.1 Transmitter : Make sure the ON/OFF switch is at the OFF position before setup. Connect power adaptor to transmitter. Plug power adaptor to wall outlet.. Connect transmitter to A/V source you want to view or hear at another location. Set the transmitting channel at back panel of transmitter. See “Channel and dwell time selection” to setup the channel.. If you want to us remote relay function, please refer “Using the remote relay feature”.
3.2 Receiver : Make sure the ON/OFF switch is at the OFF position before setup. Connect power adaptor to receiver. Plug power adaptor to wall outlet. Connect receiver to TV set or other A/V displays. Set the receiving channel same as transmitter at back panel of receiver. See “Channel and dwell time selection” to setup channel. Turn the ON/OFF switch to ON position, the related channel indicator should be lit.
4 Channel and dwell time selection 4.1 Transmitter channel setting The transmitter of video sender can send A/V source by the channel that you selected. You can use up to 4 transmitter in the same time, but make sure each transmitter is set in different channel. Receiver can receive all channel sequentially as you specified. 1 For example as the figure, A/V signal was send by channel 1. 4.
b. set by optional remote handheld Channel select Press “CH1”, ”CH2”, ”CH3”, ”CH4” to select the channel you want to receive. Scan mode channel selection If you want to receive channel 2 and 4 sequentially : 1. Press “PRGM”, all 4 channel indicator will be lit. 2. Press “CH2”, CH 2 indicator will be flash. 3. Press “CH4”, CH4 indicator will be flash too. 4. Press “PRGM”, all 4 channel indicator will be flash quickly for 5 times.
5 Using the remote relay feature 1. Plug the IR extender to the transmitter of video sender. 2. Locate the IR sensor of the A/V source equipment you want to control. You can find it by user’s manual of the equipment. 3. Point the lamp of IR extender to the IR sensor of A/V equipment you want to control. Both the IR extender lamp and the IR sensor are with working angle about ±30 to ±40 degree. So be sure the IR extender is pointed to the IR sensor in general direction. 4.
6 Trouble shooting 1. No video or sound Check the power switch on the back side of both transmitter and receiver. Check the A/V source. Make sure all cables are connected correctly (especially for euro/scart connector). Make sure the channel setting are match in both transmitter and receiver. 2. Interference in video and sound If there has any microwave oven close by, please turn off the oven when you use video sender. Change different channel to avoid interference from other device. 3.