THE FEATURE ORIENTED PHONE SYSTEM FOR EVERY HOME With exclusive Emergency Help System you can Call-4-Help with a press of a button Hear who is calling before you decide to answer an incoming phone call* Answer your phone and speak hands-free even if you can’t get to the phone** USER MANUAL ClearVoice 50 B™ ClearVoice 100 B™ ClearVoice 200 B™ CALL BACK CALL# AM REPEAT NEW VOICE CLIP PM SCROLL DELETE MENU LOUD LOW ABC DEF 1 2 3 GHI JKL MNO 4 5 6 PQRS TUV WXYZ 7 8 0 9 # HANDSET
TABLE OF CONTENTS Important Safety Instructions ...................................................................................................................................2 Safety Instruction for Batteries ......................................................................................................................................2 Installation Instructions ........................................................................................................................................
IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. 2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. 3.
IMPORTANT NOTES • The telephone portion of your dialer/message console has been tested and found to comply with all applicable UL and FCC standards. • This product is not a security system or an emergency service device. • The manufacturer makes no claim as to the suitability of this product to perform as a life-saving device. See section marked LIMITED NINETY DAY WARRANTY for full warranty conditions.
a) A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.
LOCATION OF CONTROLS 1. EXT button* 2 . CALL BACK / OK button 3. DELETE button 15. button 16. MENU button 17. Tone Hi/Lo switch 4. Handset Holder 18. 5. button 6. Speaker 7 . Handset volume control 8. Dial keypad 9. Loud LED 10. Display 11. New Call LED 12. button 13. button 14. Ringer Hi/Mid/Lo switch CLIP (Exit) button 19. FLASH button 20. switch 21. HOLD button 22. REDIAL button 23. Ringer LED 24. SPEAKER button with LED 25. Pendant button 26.
INSTALLATION Where to install this feature-oriented telephone When installing this feature-oriented telephone, consider that the unit should be placed in an area of common use during the day and night time. ClearVoice 50B, 100B and 200B™ users should locate the phone within 10-15 feet line of sight from where user spends a lot of time. The remote pick-up can be from a distance far greater than the 10-15 feet.
Choose your location Your ClearVoice 50B, 100B or 200B must be placed on a hard surface and connected to both the telephone wall jack and an 115V AC power source. Do not plug into a 115V AC power source that is controlled by a switch. Allow at least one inch to the rear and four inches above the unit for ventilation. We suggest you locate it in a location within 10 feet of where user spends much of their time. You can activate the speakerphone on an incoming call.
SPECIAL HIGHLIGHT FEATURES The Phone that will automatically hang up if accidently left in Speakerphone mode for a period of time.
USING FEATURES OF YOUR TELEPHONE THAT DO NOT NEED PROGRAMMING Notes: To program names and #s for the featured Phone Book and Emergency Help System as well as add’l programmed features proceed to section: SETTING UP TO USE THE PROGRAMMABLE FEATURES OF YOUR UNIT Before proceeding, move speaker phone control on side of unit to mid-position. Ringer Volume Control The ringer sound level can be adjusted by sliding the RINGER switch located on the side of the unit to select high (HI), mid (MID) and low (LO) level.
Speaker Volume Control You can adjust the speaker volume for a more comfortable listening level by sliding the switch. This will also adjust the volume of the voice driven features as well as speakerphone levels when speaker button activated. It is suggested to maintain the volume at medium level. Redial Note: To redial the last number called. 1. Lift the handset or press SPEAKER button. 2. Press the REDIAL button. Noted: The last number dialed (up to 32 digits long) can be redialed.
Setting the LCD contrast (If LCD contrast is OK, press Exit button) Note:depending on the viewing angle of the telephone, the user may want to adjust the LCD contrast: 1. Press and release the MENU button. The display shows LCD CONTRAST. 2. Press the OK button (located upper front left. The display shows the current contrast setting with values between 1 and 5. 3. Press or scroll buttons (upper front right) and scroll to select the desired contrast level. Press OK button again to accept.
Storing up to 30 telephone numbers in the phone book including emergency nos. to be called in an emergency. Entering Emergency telephone numbers and names: (for Emergency Help System) Note: If you have a telephone system where it is may be required to put a pause (P) before dialing a particular digit press the REDIAL button and a 3.6 second pause will be created.
General Telephone nos.
If you have already recorded a name associated with a phone #, press MENU button to go to next step or press Exit button. To change or record a voice name to a telephone # in the Phone Book.. 1. Press and release the Menu button until the Name Recording is shown on LCD display 2. Press and hold down OK button.. you will hear a Beep..speak into unit with the Name related to the telephone #.
This telephone is able to write on the LCD and to give you a voice guide in two different languages. By selecting the language the user will automatically select both the voice and the written LCD language. 1. Press and release the MENU button until LANGUAGE is shown. 2. Press the OK button, the display shows ENGLISH (for example). 3. Select the desired language scroll the or buttons. Confirm with OK button. Unit will say Language.. 4. Press CLIP (Exit) button to exit this set-up mode.
To Delete the Phone Book Memory (All telephone #s including Emergency #s and their location) 1. Press and release CLIP (Exit) button, icon is shown. 2. Select the required location from the phone book by scrolling or buttons. 3. To delete single memory, press DELETE button once. The display will show the DELETE?. Press DELETE button for 2 seconds. The telephone number and name will be deleted and the display will now show another number from the phone book.
Important: Emergency Help System feature Note: The phone book allows you to enter, display, record the persons name and specify if this a telephone no. that is to be called in the units Telemergency Emergency Help system. It is important to note that any telephone # entered that is less than 6 digits (including pauses area codes or any other digits will only be called 1 time if the emergency help system is activated. (Ex. 911).
speakerphone button or if using the dual pendant . Press the red button on pendant for more than 8 seconds. LED will stop flashing and remain on for approximately 5 seconds. 5. If a called party presses 0 on their tone dialing telephone after hearing the emergency message, the emergency speakerphone feature will be activated allowing the called party to speak to the caller, and the caller can respond (if near or able) for up to 1 minute if near speakerphone of the ClearVoice 200B.
2. The telephone dials out the first of the entered emergency numbers (stored in the phone book emergency location1) in speakerphone mode, and then begins playing the emergency message. If during the period the emergency message is played (if available to the called party), called party can acknowledge the call by pressing 0, the telephone will be put in speakerphone operation for 1 minute. After 1 minute, the phone beeps loudly for 7 seconds.
Receiving a Call (the telephone can store up to 64 calls) • If only the caller’s phone number is received, the display shows the caller’s phone number with the time and date it was received. The NEW icon turns on and NEW CALL LED turns on. Notes: 1. CALL#01 means this data is stored in Caller ID memory location #01. 2. The calling time and date are immediately recorded from the real-time clock.
Note: If the Caller ID number is 10 digits, press OK button once, the unit will insert “1” before the Caller ID number automatically. You can press button to select insert “1” or not. Press OK again, the speakerphone will turn on automatically and dial the display number. Copy from the Caller ID to the Phone Book You can copy Caller ID information to the phone book while you are reviewing the Caller ID information. 1. Select the required Caller ID memory location by scrolling or buttons. 2.
LIMITED NINETY-DAY WARRANTY This product is warranted by Telemergency, Ltd. against manufacturing defects in material and workmanship under normal use for ninety (90) days from the date of purchase. EXCEPT AS PROVIDED HEREIN, TELEMERGENCY, LTD. MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, TELEMERGENCY, LTD.
SYSTEM 2 PRO ™ Important Applications: You are walking through your home..the phone rings….you hear the phone ring or the name or number that is calling from all System 2 Pro telephone sand can’t get to a phone. Just one simple press of a pocket-sized wireless remote, you can speak/listen anywhere in the covered areas of your home without ever picking up a handset. You need emergency help and can’t get to the telephone....
Placing a call utilizing a System 2 Pro telephone handset Note: If you want to add a System 2 Pro extension to the call, then ….press EXT button to activate the other System 2 Pro telephone(s).(Speaker light will flash on the unit) activating the extension(s) to the call. This lets you know you activated the speakerphone on the other System 2 Pro telephones. Note: To use this feature it is important that the remotely activated telephone handset(s) are not picked up) .