Specifications

ManualsBrandsPremier Image Technology ManualsElectronicsWireless Module

Table Of Contents

SKI.WB800D.3

IEEE 802.11a/b/g/n/ac/ax 1T1R Wi-Fi Module

Integrated BT 5.0

Approved by Shikun

Checked by 审核

Rechecked by 复审

Approved by 批准

Approved by customer

Comments 确认意见

Approved by 批准签字

Company’s seal 盖章

Customer’s Name:

Summary of content (19 pages)

PAGE 1
SKI.WB800D.3 IEEE 802.11a/b/g/n/ac/ax 1T1R Wi-Fi Module Integrated BT 5.
PAGE 2
SKI.WB800D.3 Content 1. Introduction（简介）.............................................................................................................. 1 2. Features（特性）......................................................................................................................1 3. General Requirements（一般要求）.......................................................................................2 4. Electrical Characteristics（电气特性）......................................................2 4.1 IEEE 802.
PAGE 3
SKI.WB800D.3 1. Introduction（简介） SKI.WB800D.3 module is based on AICSEMI AIC8800D solution.SKI.WB800D.3 is a Wi-Fi 6 / BT 5.0 combo low-power, high-performance and high-integrated wireless communication module ， which is designed for meeting the customers’ needs of small size and low cost. This module supports both WLAN and BT functions. Its WLAN/BT function supports the USB 2.0 interface, and the module meets the requirements of standard protocol IEEE 802.11 b/g/n/ax.
PAGE 4
SKI.WB800D.3 3. General Requirements（一般要求） No. Feature Description 3-1 Operation Voltage 工作电压范围 3.3V+/-0.3 3-2 Current Consumption 最大电流 600mA 3-3 Ripple 纹波 120mV 3-4 Operation Temperature 工作温度范围 0°C to +40°C 3-5 Antenna Type 天线类型 External antenna 3-6 USB High Speed USB 2.0 Interface 3-7 Storage Temperature 存储温度 -40°C to +85°C 4. Electrical Characteristics（电气特性）除非另有说明，电气规范试验都在下列条件下进行: 环境条件温度：25℃±5℃；电源电压：模块输上入电压 3.3V+/-0.
PAGE 5
SKI.WB800D.3 RX Characteristics Min. Typ. Max. Unit 1) 1Mbps (FER ≦8%) - - -83 dBm 2) 2Mbps (FER ≦8%) - - -80 dBm 3) 5.5Mbps (FER ≦8%) - - -79 dBm 4) 11Mbps (FER ≦8%) - - -76 dBm -10 - - dBm 5 Minimum Input Level Sensitivity (each chain) 6 Maximum Input Level (FER ≦8%) 4.2 IEEE 802.11g Section(2.4GHz) Items Contents Specification IEEE802.11g Mode OFDM Channel CH1 to CH13 Data rate 6, 9, 12, 18, 24, 36, 48, 54Mbps TX Characteristics Min. Typ. Max. Unit 11.0 13.
PAGE 6
SKI.WB800D.3 8) 54Mbps (PER ≦10%) 6 Maximum Input Level (PER ≦10%) - - -65 dBm -20 - - dBm 4.3 IEEE 802.11n HT20/40 Section(2.4GHz) Items Contents Specification IEEE802.11n HT20/40@2.4GHz Mode OFDM HT20:CH1 to CH13 Channel HT40:CH3 to CH11 Data rate (MCS index) TX Characteristics MCS0/1/2/3/4/5/6/7 Min. Typ. Max. Unit 11.0 13.0 15.
PAGE 7
SKI.WB800D.3 4.4 IEEE 802.11ax HE20/40 Section(2.4GHz) Items Contents Specification IEEE802.11ax HE20/40@2.4GHz Mode OFDMA HE20:CH1 to CH13 Channel HE40:CH3 to CH11 Data rate (MCS index) TX Characteristics MCS0/1/2/3/4/5/6/7/8/9 Min. Typ. Max. Unit 11.0 13.0 15.
PAGE 8
SKI.WB800D.3 4.5 IEEE 802.11a Section(5GHz) Items Contents Specification IEEE802.11a Mode OFDM Channel CH36 to CH165 Data rate (MCS index) TX Characteristics 6, 9, 12, 18, 24, 36, 48, 54Mbps Min. Typ. Max. Unit 9.0 11.0 13.
PAGE 9
SKI.WB800D.3 4.6 IEEE 802.11n HT20/40 Section(5GHz) Items Contents Specification IEEE802.11n HT20/40@5GHz Mode OFDM HT20:CH36 to CH165 Channel HT40:CH38 to CH163 Data rate (MCS index) TX Characteristics MCS0/1/2/3/4/5/6/7 Min. Typ. Max. Unit 9.0 11.0 13.
PAGE 10
SKI.WB800D.3 4.7 IEEE 802.11ac VHT20/40 Section(5GHz) Items Contents Specification IEEE802.11ac VHT20/40@5GHz Mode OFDM VHT20:CH36 to CH165 Channel VHT40:CH38 to CH163 Data rate (MCS index) TX Characteristics MCS0/1/2/3/4/5/6/7/8/9 Min. Typ. Max. Unit 9.0 11.0 13.
PAGE 11
SKI.WB800D.3 4.8 IEEE 802.11ax HE20/40 Section(5GHz) Items Contents Specification IEEE802.11ax HE20/40@5GHz Mode OFDMA HE20:CH36 to CH165 Channel HE40:CH38 to CH163 Data rate (MCS index) TX Characteristics MCS0/1/2/3/4/5/6/7/8/9 Min. Typ. Max. Unit 9.0 11.0 13.
PAGE 12
SKI.WB800D.3 4.9 Bluetooth Section Items Contents Specification BT2.1+EDR/4.2/5.2 with BLE Mode FHSS,GFSK,DPSK,DQPSK Number of Channel 79 Channels Frequency Band 2.402 GHz ~2.480GHz Min. Typ. Max. Unit 1. Output Power - 3.0 - dBm 2. Gain step - 1 - dB 3. Receiver sensitivity (BER ≦0.1%) - -93.5 -80 dBm 4. Maximum usable signal (BER ≦0.1%) - -5 - 5. C/I co-channel (BER<0.1%) - 4 11 dB 6. C/I 1MHz (BER<0.1%) - -14 0 dB 7. C/I 2MHz (BER<0.1%) - -42 -30 dB 8.
PAGE 13
SKI.WB800D.3 5. Reference Design（参考设计） 5.1 Timing specification（时序规范）时序要求 5.2 DC Electrical Characteristics（直流电气特性） Symbol Description conditions Min. Typ. Max. Unit VDD33 Power supplies - 3.0 3.3 3.6 V VDDIO I/O input power supplies - 3.0 3.3 3.6 1.7 1.8 1.9 IVDD33 Power supply current - - - 800 mA IVDDIO I/O supply current - - - 50 mA VIH High-level input voltage VDDIO=3.3V VDDIO*0.625 VDDIO=1.8V VDDIO*0.65 - VDDIO+0.
PAGE 14
SKI.WB800D.3 10Hz to 30Hz to visual inspection and the products should 10Hz,amplitude 2.0mm, be ok. 5 times vibrations, 5x times vibration. 1.After soldering, the soldered area must be covered by a smooth bright solder Soldering 2-1 ability test (Only for SKI module) Soldering layer, some deficiencies such as a small temperature: amount of the pinhole, not wetting are 3 245±5℃ allowed, but the deficiencies can not be Soldering duration: in the same place； 3±0.5S 2.
PAGE 15
SKI.WB800D.3 with the test specification. 2-8 2-9 Aging Test Salt spray test 60℃，120Hrs 10 The products at high temperature for a long time can continuous work normally The Sample shall has no minor or major NSS,35℃,PH:6.5~7.2, 24H 2 defects, such as physical damage, crack, corrosion, deformation etc; Discharge voltage: 1kV C: 150pF 2-10 ESD Discharge resistance：330Ω Positive10 times 1 time for each second 7. aphorism（警語） 13 3 The products can recoverable smoothly after ESD test.
PAGE 16
FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditio ns: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
PAGE 17
End Product Labeling If the FCC identification number is not visible when the module is installed insideanother device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: 2A7WHSKIWB800D3 Table for Filed Antenna Antenna Type Dipole Antenna For BT/BLE: 2400~2500MHz: ANT B:3.19dBi Antenna Gain. For WLAN 2400~2500MHz: ANT A:3.
PAGE 18
ISED Statement ‐ English: This device complies with Industry Canada license‐exempt RSS standard(s).Operation is s ubject to the following two conditions: (1) This device may not cause interference, and (2) This devic e must accept any interference, including interference that may cause undesired operation of the de vice.The digital apparatus complies with Canadian CAN ICES‐3 (B)/NMB‐3(B). ‐ French:Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
PAGE 19
Note Importante: Dans le casoùces conditions ne peuventêtresatisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autreémetteur), l'autorisation du Canada n'est plus considérécommevalide et l' ISED ne peut pas êtreutilisé sur le produit final. Danscescirconstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y comprisl'émetteur) etl'obtentiond'uneautorisationdistincte au Canada.