User's Manual

QUICK START
1. Connect the PRYME BLU adapter to a compatible two-way radio.
2. Pair the PRYME BLU Adapter with a compatible wireless audio accessory.
3. Connect a wired audio or PTT accessory to the Quick-Disconnect accessory port on the
PRYME BLU Adapter (optional).
4. Test and use.
STEP ONE: Connecting to Two-Way Radio
To connect your PRYME BLU Adapter to a two-way radio, follow these steps:
* Always turn o your two-way radio before connecting the PRYME BLU Adapter.
* Plug the PRYME BLU adapter into the speaker-microphone / audio accessory jack of your two-way radio.
* On some models of two-way radio, you may need to tighten a retaining screw to ensure that the
PRYME BLU adapter remains attached to the radio
* Turn on your two-way radio and verify that the radio transmits and receives with the adapter attached.
* Because no wireless audio accessory will yet be paired to the PRYME BLU Adapter, received signals
should be heard over the radio’s internal speaker and transmitted signals will be sent using the radio’s
internal microphone.
* The Talk button on the PRYME BLU Adapter will not function as a Push-to-Talk button for your two-way
radio until a wireless audio accessory is successfully paired to the adapter, or a wired audio accessory is
plugged into the Quick-Disconnect port.
2
3 4
PRYME BLU ADAPTER USER’S GUIDE For Compatible Wireless Audio Accessories
Quick Disconnect Accessory Port
Allows the connection of a PRYME QD
series wired audio accessory, such
as a Push-to-Talk, earphone,
or auxiliary microphone.
Bluetooth Adapter Model No.: BT-523 Made in Taiwan FCC ID: N2E-BT-523
Radio Connector
This port connects the PRYME BLU
Adapter to a compatible two-way radio.
Multi-Function Talk Switch / Status LED
Used to place the PRYME BLU Adapter in pairing mode.
The LED ashes messages that let the user know the
current status of the PRYME BLU Adapter. Once paired
with an audio accessory, this switch is used to activate
the Push-To-Talk function of the two-way radio.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure compliance requirements, please avoid direct contact to the transmitting antenna during transmitting. RF Exposure Warning! Please keep product 20cm away from your body or bystander during the radio operation. The typical handheld two-way radios were certied under mobile usage condition (i.e. keep 20cm away from the user body) and use of such radio closer than 20cm may exceed the US RF exposure limit and shall be avoided.
STEP TWO: Pairing with an Audio Accessory
* Turn o the radio that the PRYME BLU Adapter is connected to. Wait at least three seconds.
* Turn the radio on while holding down the Talk button on the PRYME BLU Adapter.
* Continue to hold the Talk button down for approximately three seconds. Release the Talk button
when the status LED begins to ash two times per second.
* The PRYME BLU Adapter is now in audio accessory pairing mode. Activate the pairing mode on
your compatible wireless audio accessory.
* Once the wireless audio accessory and PRYME BLU Adapter are paired with each other, the status
LED on the adapter will show a constant blue light for three seconds.
* If the PRYME BLU Adapter does not detect a compatible wireless accessory within 60 seconds
of being put into pairing mode, the adapter will exit the pairing mode and resume normal operation.
* Once successfully paired, you will be able to operate your two-way radio using your compatible
wireless accessory.
Pairing With an Audio Accessory
Connecting the Adapter to Radio
Controls and Connection
The PRYME BLU Adapter allows you to use a compatible wireless headset or other audio accessory with your two-way radio.
version 1.0 July 2009
PRYME® and PRYME BLU™ are trademarks owned by PRYME Radio Products, Brea CA. All other product or service names are the property of their respective owners. © 2009 PRYME Radio Products, Brea CA. All Rights Reserved
911 Mariner St., Brea, CA 92821
PH: 714.257.0300 FAX: [phone]
TOLL FREE: 800.666.2654
WWW.PRYME.COM