Wireless Entertainment System Model xTV-9T Transmitter Model xTV-9R Receiver Operation Manual 20031 142nd Ave. NE, P.O. Box 7202 Woodinville, WA 98072-4002 Sales (800) 227-3461 Fax (425) 486-3856 www.cardiotheater.com www.enercise.tv FCC NOTICE This device complies with Part 15 of the FCC Rules.
TABLE OF CONTENTS Step 1: Setting Transmitter Number USA & Canada Mode Australia Mode Page 1 Page 2 Step 2: Connecting Transmitter to TV Page 3 Step 3: Installing Receiver Page 4 Step 4: Programming Receiver Page 5 Specifications Page 6 Warranty / Technical Support Page 7-8
STEP 1: SETTING TRANSMITTER NUMBER / USA & CANADA MODE Simply set the left and right dials on the rear of the transmitter to the corresponding numbers below.
STEP 1: SETTING TRANSMITTER NUMBER / AUSTRALIA MODE Warning! End user is responsible for following the number chart below for use in Australia. Setting Transmitter dials to any other number than the ones detailed in the chart below may result in fines and or additional punishment by local authorities. Simply set the left and right dials on the rear of the transmitter to the corresponding numbers below.
STEP 2: CONNECTING TRANSMITTER TO TELEVISION Important: Television with “Audio Output” jack required. 1. Connect provided patch cable into Left & Right Audio Output Jack on rear of TV. 2. Plug other end of patch cable into the Left & Right Audio Input jack on rear of transmitter. 3. Plug provided AC adapter into 110 AC outlet. 4. Turn TV Speakers OFF via TV menu function. 5. Turn TV volume up at least 50%. 6. Adjust audio level control so red “Peak” light blinks on and off.
STEP 3: INSTALLING RECEIVER Mounting Receiver The Enercise xTV Receiver is designed to mount to any make or model of cardio equipment. 1. Insert two nylon wire ties (provided) through the holes in the mounting bracket on the rear of the Enercise xTV Receiver. 2. Wrap wire ties tightly around the bar so the receiver does not rotate. ΝΟΤΕ: Do not place receiver where it would interfere with the cardio unit controls or display panel.
STEP 4: PROGRAMMING xTV-9R RECEIVER This function enables the receiver to program the exact amount of transmitters and number them accordingly. Enercise Auto Program Mode (When Using Enercise Transmitters): 1. To activate program mode, press Volume UP and Down buttons simultaneously for 3 seconds. The number 1 with a decimal point on the left side will pop up in display window 2. Press the EQ button to begin Scanning. Scanning will take about 15 seconds. 3.
XTV-9T Specifications Input Sensitivity 100 to 1 volt Input Impedance 10K ohms Level Gain Control -70 dBm to + 10dBm Transmission Frequency 905MHz to 925.6MHz Signal to Noise -70 dBm ref .7 volts RF Output 0.48 mW EIRP Distortion <2 %. Audio Frequency Response 20Hz to 15KHz Weight 1 lbs. Power Requirements 12 VDC 200 mA Dimensions W: 5.50" H: 1.48" D: 5.
WARRANTY Cardio Theater warrants the xTV wireless entertainment system to be free from defects in material and workmanship for the following period of time from date of shipment, provided that the products have not been subject to mechanical, electrical, or other abuse or modifications.
TECHNICAL SUPPORT Technical Support Numbers Telephone USA Fax UK (800) 776-6695 (425) 486-9292 (425) 486-3856 +44 (0) 1869-238531 Technical Support Hours: 7:30 AM to 5:00 PM Monday through Friday PST. Write To: Cardio Theater Holdings, Inc 20031 142nd Ave. NE, P.O. Box 7202 Woodinville, WA 98072-4002 Notice Due to continuing advancements in technology, Cardio Theater reserves the right to make changes in hardware, packaging, and any accompanying documentation without prior written notice.