XL WASH 1500 PR-2805/PR-2805M This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in a safe place for future reference. PR LIGHTING LTD. http://www.pr-lighting.
INDEX 3 4 4 5 5 6 6 6 7 10 11 14 14 14 14 15 16 19 20 SAFE USAGE OF THE PROJECTOR INSTALLING THE PROJECTOR FITTING THE LAMP POWER SUPPLY – MAINS CONTROL CONNECTIONS DMX TERMINATOR SETUP OPTIONS-PROJECTOR CONFIGURATION TO SET THE DMX START ADDRESS OPERATION MENU ERROR MESSAGES DMX PROTOCOL LED INDICATION MAINTENANCE LUBRICATION KEEPING THE PROJECTOR CLEAN TROUBLESHOOTING TECHNICAL DATA ELECTRICAL DIAGRAM COMPONENT ORDER CODES Please note that as part of our ongoing commitment to continuous product developm
SAFE USAGE OF THE PROJECTOR When unpacking and before disposing of the carton check there is no transportation damage before using the projector. Should there be any damage caused by transportation, consult your dealer and do not use the apparatus. The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other liquids.
INSTALL THE PROJECTOR WARNING SAFETY CORD (2PCS) To pass 2 SAFETY CORDS through 4 HOLES for safety! CLAMPS (2PCS) 257 HANDLES (2PCS) 106 Take 2 clamps and 2 safety cords out from the package and mount 2 clamps on the underside of fixture with 4 retainers attached to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp.
POWER SUPPLY-MAINS Connect the power cord as follows: L (live) =brown E (earth) =yellow/green N (neutral) =blue Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel of the projector. It is recommended that each projector be supplied separately so that they may be individually switched on and off. IMPORTANT It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant standards.
DMX TERMINATOR In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents electrical noise from disturbing and corrupting the DMX control signals. The DMX terminator is simply an XLR connector with a 120Ω (ohm) resistor connected across pins 2 and 3, which is then plugged into the output socket on the last projector in the chain. The connections are illustrated below.
OPERATION MENU 1st LEVEL 2nd LEVEL PR LIGHTING XL SERIES XL 1500 WASH DMX Address=001 DMX Address Reset 3rd LEVEL DMX Address 001-499 in short mode 001-496 in stand mode 001-490 in extended mode Reset Are You Sure? DMX Mode Lamp Control Loss of DMX DMX Mode Standard 16 DMX Mode Extended 16 DMX Mode Short 8 Lamp Control By Control Channel Lamp Control By Power On Lamp Control By DMX Present When DMX is Lost Normal Time Out When DMX is Lost Hold Last Value Config Settings Factory Settings (Press b
ON CMY Invert OFF CMY Invert ON CTO Invert OFF CTO Invert ON Defaults OFF Defaults Restore Defaults Display On Always Display Off After Delay Display Invert OFF Display Invert ON Disp Dim Level Min Disp Dim Level 1 Disp Dim Level 2 Disp Dim Level 3 Disp Dim Level 4 Disp Dim Level 5 Disp Dim Level 6 Disp Dim Level 7 Disp Dim Level 8 Disp Dim Level 9 Disp Dim Level Full Display Contrast XXX(1~36, Default is 16) Language = English Language = Chinese Lamp Hours = XX Total Hours = XX CMY Invert CTO Invert Def
Factory Setup OFF Factory Setup ON Self Test OFF self test ON Status = XXX Control = X Factory Setup Test Modes Self Test Lamp Manual Control Lamp Status Turn Lamp On Turn Lamp Off 9/22
ERROR MESSAGES In the course of launch, XL WASH 1500 examines automatically whether there are errors and if there are, it will display information as follows: Display Sensor Err Sensor Err Sensor Err Sensor Err Sensor Err Sensor Err Sensor Err Sensor Err Sensor Err Sensor Err Sensor Err Sensor Err S1-M1 S1-M2 S1-M3 S1-M4 S1-M5 S1-M6 S2-M1 S2-M2 S2-M3 S2-M4 S2-M5 S2-M6 Message Colour wheel 1 (1# drive board motor 1) error CTO (1# drive board motor 2) error CYM-cyan (1# drive board motor 3) error CYM-yellow
DMX PROTOCOL Short mode 1 2 Standard mode 1 2 Extended mode 1 FUNCTION Strobe 2 Dimmer 3 Dimmer Fine 3 3 4 CYM Macro 4 4 5 11 CYM-Cyan CYM-Cyan Fine CYM-Yellow CYM-Yellow Fine CYM-Magenta CYM-Magenta Fine CTO 12 CTO Fine 6 5 5 7 8 6 6 9 10 7 8 7 8 13 Colour Wheel 1 11/22 DMX DESCRIPTION 000-010 Black 011-025 Open 026-225 Strobe speed from slow to fast 226-255 Open 000-007 Black 008-255 Dimming from dark to light (0-100%) 000-255 000-016 017-035 036-054 055
140-145 Rainbow rotation speed 3 146-151 Rainbow rotation speed 4 152-157 Rainbow rotation speed 5 158-163 Rainbow rotation speed 6 164-169 Rainbow rotation speed 7 170-175 Rainbow rotation speed 8 176-181 Rainbow rotation speed 9 182-187 Rainbow rotation speed 10 188-195 202-207 Stop in current position Rainbow reverse rotation speed 1(slowest) Rainbow reverse rotation speed 2 208-213 Rainbow reverse rotation speed 3 214-219 Rainbow reverse rotation speed 4 220-225 Rainbow reverse r
188-195 202-207 Stop in current position Rainbow reverse rotation speed 1(slowest) Rainbow reverse rotation speed 2 208-213 Rainbow reverse rotation speed 3 214-219 Rainbow reverse rotation speed 4 220-225 Rainbow reverse rotation speed 5 226-231 Rainbow reverse rotation speed 6 232-237 Rainbow reverse rotation speed 7 238-243 Rainbow reverse rotation speed 8 244-249 Rainbow reverse rotation speed 9 250-255 Rainbow reverse rotation speed 10 196-201 10 10 15 Zoom 16 Zoom Fine 11 11
LED INDICATION Green Yellow Blue Red/Green On Off Flash On On Red Green DMX signal OK No DMX signal DMX signal error Setting the panel Power Running self test mode Reserved MAINTENANCE If the projector’s lens becomes damaged or broken it should be replaced. If the lamp becomes damaged or deformed in any way it must be replaced.
TROUBLESHOOTING PROBLEM ACTION ¾ Check the fuse on the power socket. ¾ Replace the lamp. The lamp comes on but the projector ¾ Make sure that the projector is correctly configurated. doesn’t respond to the controller ¾ Replace or repair the DMX cable. The projector only functions intermittently ¾ Make sure the fan is working and not dirty. ¾ Check the lenses are not broken. ¾ Remove dust or grease from the lenses. ¾ Make sure the lamp is installed correctly.
TECHNICAL DATA VOLTAGES: Electronical ballest(PR-2805): 200/220/230/240V AC，50/60Hz Options: 100/120V AC，50/60Hz 220VAC ，50/60Hz Magenetic ballest(PR-2805M): Options: 200/230/240V AC，50/60Hz POWER CONSUMPTION: Electronical ballest(PR-2805): 1700W@220V Magenetic ballest(PR-2805M): 1800W@220V LAMP: OSRAM HTI 1500 W/D7/60 Colour Temperature 6000°K Socket SFc10-4，double ended Manufacturers Rated Lamp Life 750 Hours replacement Or PHILIPS MSR Gold 1510 SA DE Colour Temperature 5800°K Socket
HEAD MOVEMENT: Pan 450º, Tilt 270º with auto position correction BEAM ANGLE: 10°narrow angle mode 15°～42° CONTROL: DMX512, 3 pin, 5 pin interfaces 14 channels in short mode, 17 channels in standard mode, and 23 channels in extended mode.
SIZES: See at below 448 238 535 453 755 505 548 LIGHT OUTPUT: 42°（ lux） 15°（ lux） 10°（ lux） 16m 8m 0m 8m 16m 6830 38120 85770 1700 9730 21440 760 4230 9530 430 2380 5360 270 1520 3430 20m 12m 4m 10° 15° 42° 4m 12m 20m DISTANCE (m) 0 5 10 15 20 25 1.77 2.66 3.55 4.43 10° DIAMETER (m) 0 0.89 15° DIAMETER (m) 0 1.33 2.65 3.98 5.30 6.63 42° DIAMETER (m) 0 3.71 7.43 11.44 14.85 18.
M1-6A DIMMER-1 D D B B C C A A View side of no axletree M2-6 STROBE 2 View side of no axletree D D B B C C A A MOTOR6 View side of no axletree D D B B C C A A MOTOR5 View side of no axletree View side of no axletree D D B B C C A A MOTOR4 M2-5 STROBE 1 View side of no axletree D D B B C C A A MOTOR3 M2-2 M2-3 M2-4 Inside Fresnel Lens 1 Inside Fresnel Lens 2 COLOUR 2 View side of no axletree D D B B C C A A MOTOR2 V S G MOTOR1 M2-1 Fresnel Lens Focus D D B B C C A A M1-6B DIMMER-2 Vi
M1-6A DIMMER D B C A D B C A View side of no axletree M2-4 COLOUR 2 M2-5 STROBE 1 View side of no axletree View side of no axletree View side of no axletree D B C A D B C A D B C A D B C A D B C A MOTOR6 D B C A D B C A MOTOR5 D B C A D B C A MOTOR4 D B C A D B C A MOTOR3 M2-6 STROBE 2 View side of no axletree D B C A D B C A MOTOR2 V S G D B C A MOTOR1 D B C A M2-3 Inside Fresnel Lens 2 View side of no axletree D B C A M2-2 Inside Fresnel Lens 1 View side of no axletree D B C A
COMPONENT ORDER CODES NAME POWER SUPPLY MAINS FILTER THERMOSTAT CAPACITOR**** BALLAST**** IGNITOR**** LAMP TILT DRIVE BELT PAN DRIVE BELT FAN IN BASE FAN IN FRONT SIDE FAN IN BACK SIDE FAN NEAR THE LAMP(SMALL ) FAN NEAR THE LAMP(LARGE ) FAN NEAR THE CYM FAN NEAR THE POWER PCB PAN MOTOR TILT MOTOR DIMMER MOTOR ZOOM MOTOR CYM-CYAN MOTOR CYM-YELLOW CYM-MAGENTA MOTOR CTO MOTOR COLOUR WHEEL 1 MOTOR COLOUR WHEEL 2 MOTOR ZOOM LENS MOTOR SHUTTER BLADE MOTOR PAN/TILT DRIVE PCB MOTOR DRIVE PCB 1 MOTOR DRIVE PCB 2 POW
PR LIGHTING LTD.
