www.poynting.tech WLAN-61 User Guide South Africa Europe Unit 4, N1 Industrial Park Landmarks Ave Samrand, 0157, South Africa Tel: +27 12 657 0050 info@poynting.tech Kronstadler Straße 4, 81677 München Germany Tel: +49 89 2080 265 38 Mob.: +49 176 529 733 50 sales-europe@poynting.tech Version: 1.
A-WLAN-0061_PCL
Index 1. Packing Check List 4 2. Tools Required 7 3. Mounting Configuration 8 4. Antenna Mounting Precautions 10 5. Cable Gland Preparation 10 6. Cable Routing 11 7. Safety 12 Version: 1.
1 4 Packing Check List Item Description Quantity 1. A-WLAN-0061 Antenna only 1 2. Cast U-shape 1 3. M6 x 60mm U-bolt -ss* 2 4. Cast connector rod 1 5. Cast square base 1 6. M6 washers -ss* 10 7. M6 nylock nut-ss* 2 8. M6x12mm hex bolt- 1 ss* 9. M6x16mm hex bolt – ss* 3 10. M6 nuts-ss* 4 11. M6x25mm hex bolt –ss* 2 12.
1 Packing Check List Item Description Quantity 13. Main body with back housing 1 14. Rubber flat seal 1 15. Rubber conical seal 1 16. Plastic wrench 1 * Stainless Steel Version: 1.
1 Packing Check List The appearance of each component Antenna Unit Stainless steel bracket assembly A-BRKT-016 Schematic Diagram 78 65 143 SCALE 1 : 1 SCALE 1 : 1 Cable gland components 6 A-WLAN-0061_PCL 78 65 Bracket mounting kit
2 Tools Required Tools that may be required: 6mm Masonry drill bit Impact drilling machine Screw driver-Cross slot/Philips Hammer Safety goggles Spanner/Wrench Version: 1.
3 Mounting Configuration WLAN-0061 is a pole mountable dual band WiFi antenna. It can be mounted outdoors on a pole of up to 50mm in diameter or wall mount. Follow the instructions below for installation. 1. Pole Mounting • • • • • • • • 8 Lay the antenna out at the installation site. Attach the cast U-shape bracket component to the antenna by means of four M6 washers, three M6 x16mm hex bolts and one M6x12mm hex bolt-which goes into a point marked earthing point.
3 Mounting Configuration 2. Wall Mounting • • • • This antenna should be mounted on a wall using the wall plugs as shown in the figure below Strain relieve the cable to the wall with saddles or cable tie to the closest structure. Connect the end of cable to radio device Version: 1.
4 • Antenna Mounting Precautions Place the antenna at the highest point possible and ensure that there aren’t any surrounding obstructions to the antenna. In order to avoid communication interference, ensure that the antenna is placed at least 0.5m away from other antennas and metal objects. Avoid installing the antenna near a chimney, as the smoke and soot emitted by the chimney can obstruct the signal level achieved by the antenna. Install the antenna away from heat sources and flammable gases.
4 • • • • • • Cable Routing Avoid wrapping the cables around the pole. Route the antenna cables straight down the inside of the pole to avoid using extra equipment such as cable ties. Use the minimum cable length required. Do not run more cable than needed to ensure minimum cable losses are achieved. Never pull on the cable connectors; pull only on the cable ensuring the cable is not under tension. The allowable cable bend radius is 30mm.
7 • • • Safety If you are installing an antenna for the first time or unsure about how to install your antenna, obtain the help of a professional installer. Carefully survey the installation site before installation to locate secure handholds, dangerous conditions (such as power lines and weak roofs) and the safest and most convenient placement for ladders if necessary. When installing your antenna, remember: 1. Do not install near power lines as they can electrocute you. 2.
7 • Safety When drilling, remember 1. Use safety goggles when drilling the holes. 2. Avoid using bits that are dull, bent or damaged. 3. Be aware of where your fingers are in relation to the drill bit when using the drilling machine. 4. To stop the drilling machine, let the drill chuck come to a complete stop on its own. Do not grasp the chuck in an attempt to stop the drill bit. 5. Avoid awkward hand positions where a sudden slip could cause a hand to move into the drill bit or cutting tool.