Getting Started Guide

ManualsBrandsPowerstick.com ManualsElectronicsClick+

1. About the Click+

Click+ is a small, smart button that connects to your phone or tablet through Bluetooth. Through

the free app, you can program the Click+ to perform a variety of actions to simplify interacting

with your phone.

Each Click+ can control three different actions. Single-click for your first action, double-click for

your second, and click and hold for your third.

Click+ can help you find your missing phone, control music playing from your phone, take better

photos, navigate while driving and so much more.

2. Before You Start

Here are a few important points you should know before getting started with your Click+.

A. The Click+ app MUST be running in the background of your phone to communicate with your

Click+ for a selection of the available actions. This includes: Find My Phone, Vibrate, Flashlight,

Safari, Text Message & Navigate

B. A maximum of 4 Click+ smart buttons can be connected to one mobile device at a time.

C. Click+ smart buttons can only be paired to ONE mobile device at a time.

D. The Bluetooth on your device must always be ON.

3. Getting Started

A. Remove the plastic tab from the Click+ unit. Wait 10 seconds for the battery to fully activate.

Remove the Click+ Tab Wait 10 Seconds

B. Push the Click+ smart button, you should see a small blue light blinking near the centre of the

button.

C. From your phone/tablet, make sure Bluetooth is turned ON.

D. Download the “ClickPlus by PowerStick” app from iTunes. If you have an Android, follow the

instructions here.

E. Open the Click+ app. A window will pop up asking if you would like the Click+ app to send

you notifications. Tap ALLOW for the app to perform to its full potential. (A selection of the

available actions do require notifications.)

Click+ Notification Request

F. Once your app is open, tap LET’S GET STARTED.

User Guide

CLICK+

Summary of content (6 pages)

PAGE 1
User Guide CLICK+ 1. About the Click+ Click+ is a small, smart button that connects to your phone or tablet through Bluetooth. Through the free app, you can program the Click+ to perform a variety of actions to simplify interacting with your phone. Each Click+ can control three different actions. Single-click for your first action, double-click for your second, and click and hold for your third.
PAGE 2
G. Swipe through the introduction screens to get an overview of how the Click+ works. H. On the final introduction screen, tap LET’S ADD A CLICK+. 4. Pairing Your Click+ A. If this is your first time pairing, follow the instructions from the Getting Started section to bring you to this screen. Tap LET’S ADD A CLICK+. B. As instructed in the app, press the button on your Click+ to pair it to your phone. C. You may get a pop-up telling you that the Click+ is requesting to pair. Tap PAIR. D.
PAGE 3
D. Type in the name that you would like this Click+ to have. You can name it after the person who owns the Click+ (ex. Tyler’s Click+), the name of the room it is used in (ex. Living Room), the name of the function it serves (ex. Music Control), etc. E. Tap DONE. Now your Click+ will be labelled with the new name you have given it. 7. Setting Up Your Click+ Actions A. This is the screen that shows your Click+ actions.
PAGE 4
Why won't my Click+ pair? Here are a few things to check if your Click+ won’t pair: Have you removed the plastic tab blocking the battery? Is your operating system up to date? Is your Bluetooth on? How do I replace the battery? Flip your Click+ over so you are looking at the bottom side You will see a plastic back plate that needs to be removed to place the battery inside Put your nail or a small coin in one of the slots beside “close” or “open” Turn the plate clockwise to open the Click+ Replace with CR203
PAGE 5
• Open your phone or tablet’s Bluetooth settings • Forget the Click+ device from the list of available devices • Turn your Bluetooth off for about 30 seconds • Turn your Bluetooth on again Reset your Click+ • Open the Click+ • Remove the battery for 20-30 seconds • Place the battery back in the unit • Close the Click+ back up • Wait for 10 seconds for the battery to connect
PAGE 6
FCC Statement： This device complies with part 15 of the FCC rules Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.