User Manual

ManualsBrandsPowerplus ManualsPumpsPOWXG9417 SUBMERSIBLE PUMP 750W SS +S ENSOR EN

POWXG9417 EN

1 APPLICATION .................................................................................. 2

2 DESCRIPTION (FIG A) .................................................................... 2

3 PACKAGE CONTENT LIST ............................................................. 2

4 GENERAL POWER TOOL SAFETY WARNINGS .......................... 2

5 BEFORE START-UP, NOTE THE FOLLOWING! ........................... 3

6 INSTALLATION ................................................................................ 3

7 SETTING TO WORK ........................................................................ 4

7.1 Setting the ON/OFF operating point....................................................................... 4

8 CLEANING AND MAINTENANCE ................................................... 4

8.1 Maintenance guidelines .......................................................................................... 4

8.2 Cleaning the impeller .............................................................................................. 5

9 TECHNICAL DATA .......................................................................... 5

10 SERVICE DEPARTMENT ................................................................ 5

11 TROUBLESHOOTING ..................................................................... 6

12 STORAGE ........................................................................................ 6

13 WARRANTY ..................................................................................... 6

14 ENVIRONMENT ............................................................................... 7

15 DECLARATION OF CONFORMITY ................................................ 7

Summary of content (7 pages)

PAGE 1
POWXG9417 EN 1 APPLICATION .................................................................................. 2 2 DESCRIPTION (FIG A) .................................................................... 2 3 PACKAGE CONTENT LIST ............................................................. 2 4 GENERAL POWER TOOL SAFETY WARNINGS .......................... 2 5 BEFORE START-UP, NOTE THE FOLLOWING! ........................... 3 6 INSTALLATION .........................................................
PAGE 2
EN POWXG9417 SUBMERSIBLE PUMP 750W WITH SENSOR POWXG9417 1 APPLICATION This pump is used primarily as cellar pump. When installed in a shaft, the pump provides protection from flooding. It is also used wherever water has to be moved from one place to another, e.g. in the home, agriculture, horticulture, plumbing and many other applications. It is not designed for commercial use. Pollution of the liquid could occur due to leakage of lubricants.
PAGE 3
POWXG9417 EN 5 BEFORE START-UP, NOTE THE FOLLOWING!  The pump can be connected to any shock-proof plug which has been installed according to regulations. The plug must have a supply voltage of 230V ~ 5 Hz. Fuse min. 6 Amp. Caution! When the pump is to be used near swimming pools or garden ponds and in their area of protection, it must be equipped with a PRCD (residual current circuit breaker) with a nominal trip current of max. 30 mA (according to VDE 0100, part 702 and 738).
PAGE 4
EN POWXG9417 Important Note! If the mains cable or plug suffers any damage from external action, repairs to the cable are prohibited. 7 SETTING TO WORK After having read these instructions carefully, you can set your pump to work, reconsidering the following:  Check if the pump rests on the ground of the shaft.  Check of pressure cord has been attached properly.  Check if electrical connection is 230V ~ 50 Hz.  Check if socket is in good condition.
PAGE 5
EN POWXG9417 Important ! Note! Remove the mains plug before all maintenance work.     When the pump is often transported in the course of operation, it should be cleaned out with clear water after every use. All fibrous particles which may have built-up inside the pump housing should be removed with a water jet. Every 3 months the shaft ground and as should be cleaned from mud. Remove deposits on the floater with clear water. 8.
PAGE 6
EN POWXG9417 11 TROUBLESHOOTING Incidents Pump does not start No flow Insufficient flow Pump switches of after short operating period Causes - No mains supply - Inlet sieve is clogged - Pressure hose in bent - Inlet sieve is clogged - Reduced pumping capacity by dirty and abrasive water - Thermal cutout stops pumps due to dirty water - Water too hot.
PAGE 7
EN POWXG9417  Your appliance must be returned undismantled to your dealer in an acceptably clean state, (in its original blow-moulded case if applicable to the unit), accompanied by proof of purchase. 14 ENVIRONMENT Should your appliance need replacement after extended use, do not dispose of it with the household refuse, but in an environmentally safe way. Waste produced by electrical machine items should not be handled like normal household rubbish. Please recycle where recycle facilities exist.