This is the On site milling guide for Heart
The PowerKiss Heart is a different kind of transmitter for wireless charging. It does not take up space on your table as it is attached underneath the tabletop. From there it will charge your devices, without any cables while the furniture surfaces will remain clean and free just like you have planned them to be. For this, the Heart needs to be installed into a specific hole pattern that can be done either on site or at workshop. This booklet will guide you how to do the processing on site.
WARNING To avoid injury, read all the installation instructions, operating instructions and safety information in this guide. Always use powertools and their accessories according to manufacturer’s instructions and with extreme caution. PowerKiss is not responsible for third-party products and their quality before or after the installation.
Specifications Requirements for the piece of furniture Feature Requirement Surface thickness range 22 - 57 mm (0.866 - 2.244 inches) Material restrictions No metal or magnetic materials directly above Charging Spot Minimum Charging Spot distance from the user 200 mm (8 inches) Optimal Charging Spot distance from the user 400 x 200 mm (16 x 8 inches), see picture (p.
How it should look like How it should look like 7
The ready table The Charging Spot 400 mm 200 mm The hole that is made through the surface is always on the left of the actual Charging Spot 8 How it should look like
How it should look like 9
Ø 3.5 mm (9/64 inches) Ø 75 ±1mm (2.95 ±.04 inches) 3 ±0.5mm (1/8 ±.02 inches) 45 ±0.5mm 10 (13/4 How it should look like ±.02 inches) 22 - 57 mm (0.866 - 2.
Installation in short How it should look like 11
How it should look like
What you need What you need 13
1 The jig plate and screws The PowerKiss Router Jig is compatible with all plunge-capable routers that can be fitted with a 17 mm (0.
Plunge Router 2 See that the used router bit has sufficient overall length for the target surface What you need 15
3 Copy ring for the router Ø17 mm (0.
Vacuum cleaner 4 Remember to clean after youself.
5 Drill and the correct drill bits Ø 3.
Measuring equipment 6 16.
What you need
How to do it How to do it 21
1 Check the target surface Measure the table surface thickness with extreme care, using a caliper. If the thickness is within the range specified, continue.
2 Hole through the table top Drill a hole of d= 3.
3 Turn the table and place jig plate Turn the table around and place the jig plate so that its dia = 5 mm (0.1969 inches) hole is directly above the just drilled 3.5 mm (9/64 inches) hole Ø 5 mm (0.1969 inches) Ø 3.
4 Attach the plate Attach the jig plate with the provided screws to the surface How to do it 25
5 Attach copy ring Attach the copy ring to the router 26 How to do it
6 Measure and set the plunge depth Place the router on the jig plate and measure the needed plunge depth. The surface thickness at the ready groove must be 3 ±0.5mm (1/8 ±.02 inches).
7 Do the hole Turn on the router and plunge it slowly.
8 Check the result! 75 ±1mm (2.95 ±.04 inches) 3 ±0.5mm (1/8 ±.
How to do it
Safety information Safety information 31
Safety information When using power tools, basic precautions should always be followed. In particular: • Before using any power tool, check first for damaged parts and if found, do not use them before the part or parts have been replaced with new ones • Always ensure that the path of the router is kept clear of any obstruction e.g.
• Don’t over reach; keep proper footing at all times to ensure correct balance • Wear safety goggles at all times, everyday glasses are not sufficient for eye protection as lenses are not impact resistant and could shatter. Use a face or dust mask if operation is likely to be dusty and ear defenders during periods of operations • Don’t wear loose clothing, neckties or jewellery or other items which may get caught in moving parts.
The images in this guide are examples only. POWERKISS and the “PowerKiss” Logo are trademarks or registered trademarks of PowerKiss Ltd. The “Qi” symbol is a trademark of the Wireless Power Consortium. © 2013 PowerKiss Ltd. All rights reserved. Manual no: ZMXXXX, version: 1.