User's Manual

CONTENTS
• Nano Enhanced Wireless Controller
• 6ft (1.8m) USB-C charge cable
• Pouch with drawstring
• This User Manual
SET UP
Check for system update. Nintendo Switch
™
system update version
6.0.1 or later is required for use of PowerA Wireless controllers.
1. Connect your Nintendo Switch to the Internet
2. Typically, system updates will be downloaded automatically when
connected online.
3. Select ‘System Settings’ from HOME menu, then scroll down to
‘System’ to see System Update version and automatically check for
system update.
For additional help, search ‘system update’ from Nintendo
Support website.
RECHARGEABLE 600 mAh INTERNAL BATTERY
Controller was charged at the factory, but if top LED is flashing
red, plug in USB cable to charge prior to initial pairing. Get up
to 20 hours of game play when fully charged (other variables
affect play time).
WIRELESS PAIRING
From the HOME Menu, select “Controllers,” then “Change Grip
and Order.” While the following screen is displayed, press and
hold down the SYNC Button for at least one second on the
Controller you wish to pair.
NOTE: Once controller is paired once, it will auto-connect next time.
UNDERSTANDING LED INDICATORS
1. The top LED near the USB port will flash Red when the internal
battery is near depletion. Plug in USB cable to charge once indicator
is flashing for uninterrupted game play. LED will turn solid red during
charging, and off once fully charged.
2. The front LED (between Right stick and D-pad) indicates controller
will flash during programming of Advanced Gaming Buttons.
3. The four LED on the bottom indicate power, player number 1-8, and
will cycle from left to right during wireless pairing.
ASSIGNING ADVANCED GAMING BUTTONS
1. Press and hold the program button for 2-3 seconds on the back of
the controller. The program LED (front face) will flash, signaling the
controller is in assign mode.
2.Press 1 of the following buttons (A/B/X/Y/L/R/ZL/ZR/Left Stick
Press/Right Stick Press/D-pad) to re-assign. Then press the
Advanced Gaming Button (AGR or AGL) that you wish to assign. The
Program LED indicator will stop flashing, signaling the Advanced
Gaming Button has been set.
3. Repeat for the remaining Advanced Gaming Button.
NOTE: Advanced Gaming Button assignments
will remain in memory even after disconnected.
RESETTING ADVANCED GAMING BUTTONS
1. Hold the program button down for 2-3 seconds. The LED
Connection Indicator will slowly flash, signaling the controller
is in program mode.
2. Press and hold the Assign Program Button for 5 seconds to
reset to no function.
TROUBLESHOOTING
Q1. My Wireless Controller is not pairing
A1. Confirm batteries are charged by plugging in USB-C cable.
A2. Confirm you are following the ‘Wireless Pairing’ process
listed under Setup section.
A3. Insert paper clip into small hole to right of Program button
on back to reset controller to factory settings.
CUSTOMER SERVICE
For support with your authentic PowerA accessories, please visit
PowerA.com/Support.
MOTION WARNING
Playing video games can make your muscles, joints, skin or eyes
hurt. Follow these instructions to avoid problems such as tendinitis,
carpal tunnel syndrome, skin irritation or eyestrain: • Avoid excessive
play. Take a 10 to 15 minute break every hour, even if you don’t think
you need it. Parents should monitor their children for appropriate
play. • If your hands, wrists, arms or eyes become tired or sore while
playing, or if you feel symptoms such as tingling, numbness, burning
or stiffness, stop and rest for several hours before playing again. • If
you continue to have any of the above symptoms or other discomfort
during or after play, stop playing and see a doctor.
BATTERY WARNING
Don’t attempt to replace the rechargeable battery yourself- you
may damage the battery, which could cause overheating, fire, and
injury. The Lithium-ion battery in your device should be serviced or
recycled by PowerA or an authorized provider and must be recycled
or disposed of separately from household waste. Dispose of batteries
according to your local environment laws and guidelines.
Don’t use or leave the product containing recharegeable batteries
exposed to very high temperature (e.g. at strong direct sunlight or
in a vehicle in extremely hot weather). Otherwise, it can overheat,
catch fire, or the performance will degenerate, and the service life
will be shortened.
Don’t use the rechargeable battery item in a location where static
electricity is rich, otherwise, the internal safety devices may be
damaged, causing a harmful situation.
In case the electrolyte gets into the eyes due to the leakage of
battery, do not rub eyes! Rinse eyes with clean running water and
seek medical attention immediately. Otherwise, it may injure eyes or
cause a loss of sight.
If the battery gives off an odor, generates heat, or in any way
appears abnormal during use, recharging or storage, immediately
remove it from battery charger and place it in a contained vessel
such as a metal box.
Be aware discarded batteries may cause fire, do not heat the
controller or throw it into fire.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
Customer Service
Service client
Kundendienst
Servicio a clientes
Assistenza clienti
Apoio ao Cliente
interference received, including interference that may cause
undesired operation.
Warning: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
CAN ICES-3(B)/NMB-3(B)
This device contains licence-exempt transmitter(s)/receiver(s)
that comply with Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the
following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference
that may cause undesired operation of the device.
REGIONAL COMPLIANCE SYMBOLS
More information available via web-search of each symbol name.
The WEEE symbol informs the end-user about separate disposal
requirements for WEEE (Waste of electrical and electronic
equipment) as required per the Article 11(2) of the
WEEE Directive and prescribed by European standard
EN50419:2005.
CE (Conformité Européene aka European Conformity) is a
certification mark that indicates conformity with health,
safety, and environmental protection standards for
products sold within the European Economic Area.
The Regulatory Compliance Mark is a visible indication
of a product’s compliance with all applicable ACMA (Australian
Communications and Media Authority) regulatory arrangements,
including all technical and record-keeping requirements regarding
the electrical safety and/or electromagnetic compatibility (EMC).
AUSTRALIAN WARRANTY STATEMENT
This product comes with guarantees that cannot be excluded under
the Australian Consumer Law. You are entitled to a replacement
or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have
the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure. If
purchased within Australia or New Zealand, this product comes with
a One-year warranty from date of purchase. Defects in the product
must have appeared within One year from date of purchase, in order
to claim the warranty.
All warranty claims must be facilitated back through the retailer
of purchase in accordance with the retailer’s return policies and
procedures. Any expenses incurred, as a result of returning the product
to the retailer of purchase are the full responsibility of the consumer.
AU WHOLESALE DISTRIBUTOR
Level 2, 2 Darling Street South Yarra, Australia VIC 3141
bluemouth.com.au Email: [e-mail]
[phone]
MANUFACTURED BY
Bensussen Deutsch & Associates, LLC. (BDA, LLC.) 15525
Woodinville-Redmond Rd. NE
Woodinville, WA 98072. BDAINC.com | POWERA.com
ADDITIONAL LEGAL
PowerA, and the PowerA logo are trademarks of Bensussen
Deutsch and Associates, LLC. TM and © Bensussen Deutsch
and Associates, LLC.
The Bluetooth® word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks by PowerA
is under license.
Nintendo Switch is a trademark of Nintendo. © 2020 Nintendo.
Licensed by Nintendo.
All rights reserved. All other trademarks are the property of their
respective owners.
GERMAN
INHALT
• Nano-optimierter kabelloser Controller
• 1,8 m USB-C-Ladekabel
• Beutel mit Ziehleine
• Dieses Benutzerhandbuch
AUF SYSTEMAKTUALISIERUNG PRÜFEN
Für die Nutzung von kabellosen PowerA-Controllern wird die
Nintendo Switch
™
Systemaktualisierung Version 6.0.1 oder
höher benötigt.
1. Verbinden Sie Ihren Nintendo Switch mit dem Internet
2. Im Normalfall werden Systemaktualisierungen automatisch
heruntergeladen, wenn eine Verbindung mit dem Internet
besteht.
3. Wählen Sie im Home-Menü Systemeinstellungen aus, und
scrollen Sie dann bis zu System nach unten, um die Version
der Systemaktualisierung festzustellen und automatisch auf
Systemaktualisierungen zu prüfen.
Für weitere Hilfe suchen Sie nach Systemaktualisierung auf der
Support-Website von Nintendo.
WIEDERAUFLADBARER, INTERNER AKKU (600 mAh)
Der Controller wurde im Werk aufgeladen. Sollte die LED oben
dennoch rot blinken, dann stecken Sie das USB-Kabel ein, um ihn
vor der ersten Kopplung aufzuladen. Voll aufgeladen sind bis zu
Two year limited warranty
For warranty details or support with your authentic PowerA accessories, please visit PowerA.com/Support.
Beschränkte 2-Jahre-Garantie Informationen zur Garantie oder Unterstützung zu Ihrem PowerA-Originalzubehör
nden Sie unter PowerA.com/Support.
Garantía limitada de dos años Si quieres más información sobre la garantía o necesitas ayuda con tus accesorios
originales de PowerA, visita PowerA.com/Support.
Garantie limitée de deux ans Pour plus de détails sur la garantie ou pour obtenir une assistance pour vos accessoires
PowerA d’origine, veuillez consulter le site PowerA.com/Support.
Garanzia limitata di due anni Per i dettagli sulla garanzia o per richiedere assistenza per i tuoi accessori PowerA
autentici, visita la pagina PowerA.com/Support.
Garantia limitada de dois anos Para mais informações sobre a garantia ou os acessórios originais da PowerA, visita
PowerA.com/Support.
NANO
ENHANCED
WIRELESS
CONTROLLER
USER MANUAL
Manuel de l’utilisateur
Bedienungsanleitung
Manual de usuario
Manuale per l’uso
Manual do usuário
BDA Inc.
15525 Woodinville-Redmond Rd NE
Woodinville, WA 98072
Directional Pad
Plus Button
Home Button
Minus Button
Right Bumper ZR Button
Battery Status LED Sync Button
AGR Button
Power + Player
Indicator LED
Program Button
Left Bumper
ZL Button
AGL Button
Factory Reset
Hole
Right Stick
Left Stick
Action Buttons
Advanced Gaming Button
Program Status LED
Capture Button
AGR AGL