Please do not return product to retailer. Por favor, no devuelva el producto al lugar de compra. Veuillez ne pas retourner le produit au détaillant. ENGLISH R 1--800--554--6723 Register your product online at: Registre su producto en línea en: Enregistrez votre produit en ligne à l’adresse : www.poulanpro.
IDENTIFICATION OF SYMBOLS WARNING! This chain saw can be dangerous! Careless or improper use can cause serious or even fatal injury. Read and understand the instruction manual before using the chain saw. XX_ Always wear appropriate ear protection, eye protection and head protection. Measured maximum kickback value without chain brake for the bar and chain combination on the label. Always use two hands when operating the chain saw.
SAFETY RULES OPERATE YOUR SAW SAFELY WARNING: Always disconnect spark plug wire and place wire where it cannot contact spark plug to prevent accidental starting when setting up, transporting, adjusting or making repairs except carburetor adjustments. Because a chain saw is a high-speed woodcutting tool, special safety precautions must be observed to reduce the risk of accidents. Careless or improper use of this tool can cause serious injury. S Do not operate a chain saw with one hand.
REDUCE THE CHANCE OF KICKBACK S Move at least 10 feet (3 meters) from fueling site before starting engine. S Turn the engine off and let saw cool in a non-combustible area, not on dry leaves, straw, paper, etc. Slowly remove fuel cap and refuel unit. S Store the unit and fuel in an area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. S Recognize that kickback can happen.
S S S S S Contoured Depth Gauge your left thumb under the front handlebar. Keep your right hand completely around the rear handle whether your are right handed or left handed. Keep your left arm straight with the elbow locked. Position your left hand on the front handlebar so it is in a straight line with your right hand on the rear handle when making bucking cuts. Never reverse right and left hand positions for any type of cutting. Stand with your weight evenly balanced on both feet.
of the chain brake during kickback. Activated angle represents chain stopping time relative to activation angle of chain break and resulting kick angle of saw. In all cases lower CKA values represent a safer operating environment for the user. The following guide bar and chain combinations meet kickback requirements of CSA Standards Z62.1, Z62.3, & ANSI B175.1 when used on saws listed in this manual.
ASSEMBLY Protective gloves (not provided) should be worn during assembly. ATTACHING THE BAR & CHAIN (If not already attached) WARNING: If received assembled, repeat all steps to ensure your saw is properly assembled and all fasteners are secure. Always wear gloves when handling the chain. The chain is sharp and can cut you even when it is not moving! 1. Loosen and remove the bar nuts and the clutch cover from the saw. 2. Remove the plastic shipping spacer (if present). Bar bolts Guide bar 6.
2. Turn adjusting screw clockwise until chain solidly contacts bottom of guide bar rail. Adjusting Screw Clutch Cover Adjusting Pin 3. Using bar tool, roll chain around guide bar to ensure all links are in bar groove. 4. Lift up tip of guide bar to check for sag. Release tip of guide bar, then turn adjusting screw 1/4 turn clockwise. Repeat until sag does not exist. Adjusting Screw -- 1/4 Turn Lower Hole Guide Bar 12. Install bar nuts and finger tighten only.
OPERATION KNOW YOUR CHAIN SAW READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference.
BEFORE STARTING ENGINE WARNING: Muffler is very hot during and after use. Do not touch the muffler or allow combustible material such as dry grass or fuel to do so. WARNING: Be sure to read the fuel handling information in the safety rules section of this manual before you begin. If you do not understand the fuel handling information do not attempt to fuel your unit. Seek help from someone that does understand the information or call the customer assistance help line at 1-800-554-6723.
STARTING A COLD ENGINE (or warm engine after running out of fuel) NOTE: In the following steps, when the choke/fast idle lever is pulled out to the full extent, the correct throttle setting for starting is set automatically. IGNITION SWITCH ON STOP DIFFICULT STARTING (or starting a flooded engine) The engine may be flooded with too much fuel if it has not started after 10 pulls.
Inertia activating function control WARNING: When performing the following procedure, the engine must be turned off. Grip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14″ (35 cm) above a stump or other wooden surface. Release your grip on the front handle and use the weight of the saw to let the tip of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.
Final (felling) cut here, 2 inches (5 cm) above center of notch. First cut Notch Second cut Hinge S After removing the wood from the notch, make the felling cut on the opposite side of the notch. This is done by making a cut about two inches (5 cm) higher than the center of the notch. This will leave enough uncut wood between the felling cut and the notch to form a hinge. This hinge will help prevent the tree from falling in the wrong direction.
BUCKING WITHOUT A SUPPORT S Overcut through 1/3 of the diameter of the log. S Roll the log over and finish with a second overcut. S Watch for logs with a compression side to prevent the saw from pinching. See illustrations for cutting logs with a compression side. BUCKING USING A LOG OR SUPPORT STAND S Remember your first cut is always on the compression side of the log. (Refer to the following illustrations for your first and second cut) S Your first cut should extend 1/3 of the diameter of the log.
SERVICE WARNING: Disconnect the spark plug before performing maintenance except for carburetor adjustments. We recommend all service and adjustments not listed in this manual be performed by an authorized or Master Service Dealer. HELPFUL TIP IMPORTANT: Have all repairs other than the recommended maintenance described in the instruction manual performed by an authorized service dealer.
Replace guide bar when the groove is worn, the guide bar is bent or cracked, or when excess heating or burring of the rails occurs. If replacement is necessary, use only the guide bar specified for your saw in the repair parts list or on the decal located on the chain saw. Cylinder Cover Air Filter Cover Air Filter CHECK FUEL MIXTURE LEVEL S See FUELING ENGINE under the OPERATION section. LUBRICATION Bar Oil Fill Cap S See GUIDE BAR AND CHAIN OIL under the OPERATION section.
NOTE: The chain has both left and 5. Replace with Champion RCJ--7Y or Torch R7 spark plug and tighten securely with a 3/ inch (19 mm) socket wrench. Spark 4 plug gap should be 0.025 inch (0,6 mm). 6. Reinstall the spark plug boot. 7. Reinstall the cylinder cover and 3 screws. Tighten securely. right hand cutters. File Holder File Cutter Cylinder Cover 90° Depth Gauge S Align the 30° file holder marks parallel with the bar and to the center of the chain.
4. Check and lower depth gauges. File Depth Gauge Tool Depth Gauge S Place gauge tool on cutter. S If the depth gauge is higher than the depth gauge tool, file it level to the top of the depth gauge tool. S Maintain rounded front corner of depth gauge with a flat file. NOTE: The very top of the depth gauge should be flat with the front half rounded off with a flat file.
S At the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio. OTHER S Do not store gasoline from one season to another. S Replace your gasoline can if it starts to rust. TROUBLESHOOTING TABLE WARNING: Always stop unit and disconnect spark plug before performing all of the recommended remedies below except remedies that require operation of the unit. TROUBLE CAUSE REMEDY Engine will not start or will run only a few seconds after starting. 1. Ignition switch off.
NO CLAIMS FOR CONSEQUENTIAL OR OTHER DAMAGES WILL BE ALLOWED, AND THERE ARE NO OTHER EXPRESS WARRANTIES EXCEPT THOSE EXPRESSLY STIPULATED HEREIN. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU. This is a limited warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975.
warranty claim. Poulan PRO is not liable to cover failures of warranted parts caused by the use of add--on or modified parts. HOW TO FILE A CLAIM: If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized service center, call Poulan PRO at 1--800--554--6723, or send e-mail correspondence to emission.warranty@ HCOP--emission.com. WHERE TO GET WARRANTY SERVICE: Warranty services or repairs shall be provided at all Poulan PRO service centers.