Palapala a ka mea nona

PSN Series
Power Supplies
8910013 - REV E • 05/21 PAGE 1 OF 3
Potter Electric Signal Company, LLC • St. Louis, MO • Phone: [phone] • www.pottersignal.com
Features
• PSN-64 has 6 amps regulated with 4 outputs
• PSN-106 has 10 amps regulated with 6 outputs
• May be congured as up to three class “A” Style “Z”
notication circuits
• Two Trouble relays (5A at 30VDC) General System Trouble
(programmable for AC delay) Low AC Trouble with optional
delay settings
• Diagnostic LED’s Status LED’s for Active NAC and NAC
Trouble conditions.
• Quadrasync feature synchronizes strobes from AMSECO,
Gentex, Cooper-Wheelock and System Sensor.
• Congurable output circuits (DIP switch sets options for each
circuit)
• Reference EOL allows 2K – 27K EOL value to be used
• Pass Thru mode allows the outputs to match the input signal
from FACP
Size (H x W x D) 16 1/8” W x 16 ¾” W x 3 ½” D
Enclosure Eighteen (18) gauge sheet steel with hinged, locked door
Power Input
120VAC @ 60Hz
220/240VAC @ 50Hz
5.1 Amps @ 120 VAC
2.5 Amps @ 240 VAC
Current 75mA Standby & Alarm (no external load)
Input Voltage
Trigger
15mA @ 8 – 33 VDC
Terminals 18-12 AWG
Temperature
32° F to 120°F (0°C to 49°C) with a maximum humidity of 93%
non-condensing
NAC Output 3 Amp max per NAC, Regulated
Battery Charging 27.3 @ 1A, can support 7 – 55Ah batteries
Description
The PSN series of notication power supplies oers reliable
notication power with unprecedented versatility. The power supplies
oer either 6 or 10 amps of continuous power through 4 or 6 outputs
respectively. Each output is rated at 3 amps and it may be used
continuously without any derating. The power supply operates on
either 120 VAC or 220 VAC power input and has a regulated 24 VDC
output. In addition, the power supply can charge up to 55 AH batteries
and leads the industry in housing up to 18 AH batteries. The cabinet
is constructed out of 18 gauge cold rolled steel and has a durable red
powder coat nish. In addition, a key lock is provided for securing the
door. Ample electrical knockouts are provided on the sides and the top,
allowing the installer options for running wires and maintaining the
correct separations.
The power supply oers an industry leading Quadrasync function
that allows for multiple strobe circuits of dierent brands to be
synchronized to ash at the same time. The power supply can have
four dierent brands each connected to its own circuit and all the
strobes ash together. Each output can independently be congured to
provide one of four synchronizations or steady power. This provides
unequivocal exibility in new and retrot installations. The power
supply can be congured to synchronize AMSECO®, Gentex®,
Wheelock® and System Sensor® strobe devices. Each output can
be congured to the same sync protocol or set independently. In
addition, the power supply has an input Pass Thru mode which
allows the outputs to follow the input signal from a non-supported
synchronization protocol. The power supply will recognize the type
of input being supplied and pass this through to the outputs with
Technical Specications
the same pattern. This input pass through can be selected on each
output independently. The power supply contains simple dipswitch
programming and LED indicators providing the installer the ability
to correct any possible faults. A Trouble Memory is provided to
allow an installer to review past troubles and make the necessary
repairs. Each output has an LED to pinpoint the exact circuit where
a trouble may have occurred. Relays are provided for monitoring the
general system and AC failure. Each output and be independently
congured for various applications and installations. Each output can
be independently congured for Class A or Class B operation, constant
power, ANSI Temporal Code 3, Single, Multiple or Combo Inputs or
Door Holder Power.
firealarmresources.com