2-WAY LCD REMOTE STARTER CAR ALARM AM-8050 INSTALLATION MANUAL
H1 6 PIN HEAVY GAUGE WIRING CONNECTIONS……………………………….….………..…3 H1-1 Red wire--- +12V Power input…………………………..…………………………………….….…3 H1-2 Red wire--- +12V Power input…………………………..…………………………………….….…3 H1-3 Purple wire---starter output………………………………..…………………………….……….…3 H1-4 Yellow wire---Ignition 1 Output…………………………………………….…………..….…..…..4 H1-5 Brown wire--- Ignition 2 output……………………….……………………………….….….….…4 H1-6 Orange wire--- Accessory output…………………………………………….………..…….………4 H2 14 PIN OUTPUT WIRE CONNECTION………………………….
We will explain the three basic functions of the ignition switch, when remote starting a vehicle. Since this installation will require analysis of the ignition switch functions, we recommend making the three connections blow at the ignition switch harness directly. 30A FUSE 30A FUSE FUSE BOX 12V GND BATTERY RED +12V RED +12V PURPLE (START) YELLOW IGN1 BROWN IGN2 ORANGE ACC AC OF C F ON ST AR T START MOTOR LOCK 85 86 87a 30 RELAY ORANGE ARMING H1/1 & H1/2 Red wire - +12V Power input.
Warning: This wire must be connected to the vehicle side of the starter cut relay (when used). For the electrical neutral switch configuration, this connection must be make between the starter inhibit relay (when used ) and the neutral safety switch as shown in the following diagram. Failure to connect this wire to the ignition switch side of the neutral safety switch can result in personal injury and property damage.
H2-2 Purple/black wire – (-) 300mA Channel 5 Output – Same function as H2-2. This feature allows you to remote other electric device. H2-3 Yellow/green –300mA optional trunk output – This feature allows you to remote control trunk release. H2-4 Red/black wire – (-) 300mA Channel 6 Output – Same function as H2-2. This feature allows you to remote other electric device. H2-5 Blue wire – (-) 300mA Channel 1 Output – Same function as H2-2. This feature allows you to remote other electric device.
H2-11 Blue/black wire – (-) 300mA Channel 3 Output – Same function as H2-2. This feature allows you to remote other electric device. H2-12 Orange/black wire – (-) 300mA Channel 2 Output – This will become a 1 second pulse ground by activate channel 3 on transmitter for two seconds, the current capacity of this wire is 300 mA. This feature allows you to remote other electric device. H2-13 Orange wire – (-) 300mA Grounded Output When Armed – This wire will become grounded when the alarm is armed.
H3-2 Grey wire – Ground Instant Trigger Input – This wire is the ground trigger input wire for hood/trunk pin switches. H3-3 Black/white Negative safety shut down input The green wire provides an instant shutdown for the remote start, whenever it is grounded. Connect the wire to the hand switch previously installed. BLACK/WHITE HAND BRAKE H3-4 Yellow Positive safety shut down input This wire provides an instant shutdown for the remote start, whenever it get +12 volts .
H3-8 Grey/black wire – (-) Diesel Wait – To - Start Input – In diesel vehicles it is necessary to interface with the wire that on the WAIT-TO-START light in the dashboard. This wire illuminates the bulb until the vehicle’s glow plugs are properly heated. When the light goes out the vehicle can be started. This wire is always at the connector leading to the bulb in the dashboard. It can also be found at the Engine Control Module (ECM) in many vehicles. To test and determine the polarity of this wire: 1.
H6. 4-PIN CONNECTOR FOR ANTENNA ANT The 2-way transceiver/antenna mounting location should be the upper left or lower left corner of the driver’s windshield. H7. 3-PIN CONNECTOR FOR TEMPERATURE SENSOR TEMPERATURE SENSOR (Optional) The Temperature sensor can be add on. You can monitor, through the temperature sensor’s LED screen, the present indoor temperature of the passenger compartment before cooling or heating your vehicle.
15A FUSE FUSE BOX 10A FUSE BATTERY RELAY +12V TRUNK
9TH BUILDING, TONGFUYU INDUSTRIAL PARK, LONGHUA TOWN, BAOAN, SHENZHEN CITY, CHINA.