PORTMAN ELECTRONICS (DONGGUAN) CO., LTD. RX12 receiver Operation/ Installation Manual RX12 01/13/2010 Version 1.
T35 (Two way) T35 T36 (Two way) (One way) Press button 1 once Press and hold button 1 for 2 sec. Press button 2 once Press and hold button 2 for 2 sec. Press and hold button 3 for 2 sec. Press button 4 once then press button 1 within 3 sec. Press button 4 once then press button 2 within 3 sec. Press button 4 once then press button 3 within 3 sec. Press button 4 once then press button 4 within 3 sec.
Press and hold button 4 for 2 sec. Press button 1 + 4 once together Press button 3 + 4 once together Press button 5 once then press button 1 within 3 sec. Press button 5 once then press button 2 within 3 sec. Press button 5 once then press button 3 within 3 sec. Press button 5 once then press button 4 within 3 sec. Press button 5 once then press button 5 within 3 sec.
Press button 5 once then press and hold button 5 for 2 sec. Unit Program mode on within 3 sec. (only T35) Press and hold button 5 for 2 sec. (only T35) Unit Program mode off Transmitter program mode on/off Ignition off & disarming & door open Ignition off & disarming & door open Anytime Press button 4 once then press button 5 once within 3 sec. System status check Anytime (only T35) Special function for T35 1. 2. 3.
4 -> 1 within 3 sec. Active anti car hijacking 4 -> 2 within 3 sec. Channel 2 output 4 -> 3 within 3 sec. Channel 3 output 4 -> 4 within 3 sec. Channel 4 output 4 for 2 sec. Remote start on/off 1 + 4 once Arm with bypass shock sensor 3 + 4 once Manual active ready mode 5 -> 1 within 3 sec. Silent arm 5 -> 2 within 3 sec. Silent disarm 5 -> 3 within 3 sec. Silent arm with bypass ext. sensor 5 -> 4 within 3 sec. Timer start on/off 5 -> 5 within 3 sec.
ICON Explanation Indicates that you car is locked Indicates that you car is unlocked Indicate that your siren is turned on when locking /unlocking or alarm Indicate that your remote-pager is sending signals to the controller unit Indicate that the shock sensor is turned off Indicate that the shock sensor has been triggered Indicate alarm clock mode is on Indication time hour, minute (24Hr) Vehicle’s interior temperature Celsius / Fahrenheit units Indicate your vehicle is in arm mode Indicate your vehicle
Indicate that your trunk is open Indicate that your hood is open Display remaining battery life Indicate that your vehicle door is open Indicate the turbo mode is on Indicate function transfer and setting mode Indicate the ignition key on trigger Indicate your vehicle is in remote-start mode Indicate timer start mode is on TWO WAY TRANSMITTER T35 SETTING FUNCTION Button Press 5 for 2 sec.
Press 5 once Enter clock minute setting Press 5 once Setting backlight ON/OFF Press 5 once Vibration motor ON/OFF Press 5 once Press 5 once Arm/disarm siren chirp ON/OFF Setting shock sensor bypass ON/OFF Press 5 once Auto power-off setting Press 5 for 2 sec.
function will ON (the unit arm/disarm with chirp), press button 2 set the sound function will OFF (the unit arm/disarm without chirp).
F1:01"means: already in the menus of the function selection and show the First Status in the menus 1.
Turn the chose function to the Hold 4 Four setting and the main unit for 2 sec. will operate this indication Hold 5 for 2 sec. If success, siren chirp once, flash “SUC” for 3 times If failure, siren chirp twice, flash “FAIL” for 3 times The siren will chirp 4 times to indicate that the main unit already get out function selection mode. Transmitter T35 also will Exit the function choosing mode chirp 4 times, flash “SUC” for 3 times to indicate the goods condition of communication.
PC SETUP FUNCTION When unit is in disarming & Door open status, Select the correct COM port number, and then set the following functions Default: to use factory default setting Request: read out the setting in the current page. Apply: transfer the setting to unit in the current pages. Exit: exit PC-Setup program.
BASIC CAR ALARM FUNCTION DESCRIPTION CODE LEARNING a. b. c. d. e. When in disarmed mode. Turn ignition ON, press Valet Switch 10 times within 8 seconds, siren will chirp 3 times, system will enter code-learning mode. Press any button on the transmitter, the siren will chirp accordingly for confirmation as soon as the transmitter is learned. For example, if the first transmitter is learned, the siren will chirp once.
SILENT ARMING a. b. c. d. e. f. g. In disarming state, press button 3 and button 1 once together on T36 or press button 5 once then press button 1 once within 3 seconds. Parking light will flash once. Disables engine starter. Door will be locked at 0.5seconds or 3.5 seconds (See Function Selection J1-1). Two-way transmitter LCD screen will display arm and lock icon. After 3 seconds, all the sensors are armed.
d. e. f. For each individual detector, the number of sounding cycle can be accumulated in the same arming period. (E.g. If open the door, and let the siren sound 5 cycles, and close the door, the siren will stop sound, then if open the door again, it can only sound 3 cycles.) After 8 cycles, the triggered detector will be bypassed. This detector will not be triggered again in the same arming period. The system is disarmed; the all the detector is return normal status.
d. e. f. g. Doors will be unlocked after 0.5 seconds or 3.5 seconds (see function selection J1-1).
DOOR LOCK CONTROL (WHILE DRIVING) a. b. Press button 1 to lock doors. The doors can be locked. Press button 2 to unlock doors. The doors can be unlocked. AUTOMATIC DOOR LOCK (SEE FUNCTION SELECTION J1-8) When the system is disarming and the ignition turn from OFF to ON, door will lock after 15 seconds or door will lock with footbrake is press first. AUTOMATIC DOOR UNLOCK (SEE FUNCTION SELECTION J1-9) When the ignition turns from ON to OFF, doors will automatically unlock.
CHANNEL 3 OUTPUT (SEE FUNCTION SELECTION J2-5 /J2-12) a. b. c. Anytime, first press button 4 once then press button 3 once within 3 seconds will to remote channel 3output (with 300mA negative output). The two-way transmitter LCD screen will display channel 3 output icon. If the system is in arming at this time, the trunk trigger, ext sensor is by-pass till the channel output off. After 4 seconds, the system is in arm mode again. CHANNEL 4 OUTPUT (SEE FUNCTION SELECTION J2-6 / J2-13) a. b. c.
POWER ON MEMORY This security system is equipped with circuitry that will allow the unit to remember its alarm status if the power is lost and then reconnected. VALET MODE a. b. c. d. e. f. g. The system is disarming, turn ignition ON, within 8 seconds press and hold valet switch 3 seconds for once or press button 2+4 once together on T36 or press button 5 twice within 3 seconds on T35. LED will be constantly ON, the parking light will flash once.
c. After turning ignition ON, the system will enter anti carjacking mode at once. Within 10 seconds, pressing button 1 once of the transmitter will bypass the action of turning ignition ON, and the system will exit anti carjacking mode. And the parking will flash once and siren will chirp once. Or perform Emergency disarming to exit the anti car jacking mode, that is to say, Within 71 seconds press and hold valet switch once for one second to exit anti jacking mode.
2. 2ND WAY: Please refer 2-pin code override procedure: 2-PIN CODE OVERRIDE PROCEDURE: a. b. c. d. e. Turn ignition ON, press valet switch 5 times within 8 seconds. After 8 seconds, the LED should stay ON solid for 5 seconds, after the 5 seconds LED begins to flash. When the LED flashes the 1st number of the 2-pin code, turn ignition OFF. Then turn back ON to wait for LED to flash the 2nd number of the 2-pin code.
REMOTE ENGINE START FUNCTION DESCRIPTION RPM LEARNING (SEE FUNCTION SELECTION J3-4) a. When the system is disarming and ignition ON, press valet switch 6 times within 10 seconds, the parking lights will flash twice to indicate that system has entered the RPM learning mode. b. Start the engine, when the RPM level is stabilized, press and hold valet switch till the parking lights will flash twice and the siren will chirp twice, which indicates the RPM value has been memorized successfully.
g. h. i. In auto pre-set setting mode, when the engine running, Engine will automatically running 2 minutes after ignition off as reservation. Within 2 minutes, open and close the door, the parking light will flash twice indicate that the reservation procedure is successful. If reservation produce is failed, or within 2 minutes no any action, the parking light will flash four times indication, then you must perform the step again.
d. e. Voltage input: in voltage mode the unit detects the voltage is drop 1.0V for more than 5 consecutively seconds during ‘RUN’ time (if voltage detect mode). Unsuccessful start attempts: Three consecutively unsuccessful start attempts. TIMER START MODE OPERATION a. Timer mode activation: Anytime, press and hold button 3+4 together for 2 seconds on T36 or press button 5 once then press button 4 once within 3 seconds on T35. b.
3Flashes 4Flashes 5Flashes 6Flashes 7Flashes 8Flashes hand brake input shut down. foot brake or open hood input shut down. High RPM signal over speed shut down RPM has not learned. voltage not raised or voltage has drop manual gear car not perform the reservation procedure RETURN TO FUNCTION FACTORY DEFAULT SETTING a. b. c. In disarming status, turn Ignition OFF to ON 4 times, and ignition will stay in on position.
FEATURE MENU 1: Variable 1 set-up (2 chirps) 3.5 seconds 15 seconds 2 pulse Off 30 seconds Pre set value (1 chirp) Function selection J1-1 J1-2 J1-3 J1-4 J1-5 Lock/unlock timer Lock time Unlock pulse Arm/disarm with chirp Arming delay time J1-6 Last door arming J1-7 Auto re-arm J1-8 Automatic door lock 0.
J2-4 Programmable L2 output Channel 2 output Second unlock output CH2 Output pulse output and before start disarm J2-5 Programmable L3 output Channel 3 output Horn output CH3 Output pulse after output and shutdown disarm J2-6 Programmable L4 output Dome light output CH4 Channel 4 Remote start status output and output output disarm J2-8 Trunk (Channel 1) Momentary output output Latched output Latched output and reset with 30 seconds timed ignition ON J2-9 Horn timing 10ms 50ms 20ms On
FEATURE MENU 3: Pre set value (1 chirp) Function selection (3 chirps) (4 chirps) J3-1 Vehicle model J3-2 Manual gear reservation Manual set setting J3-3 Engine checking on/off Engine checking on Engine checking off J3-4 Check mode when start Voltage checking type Tachometer checking type J3-5 High/low voltage check High voltage level check level Low voltage check level J3-6 Cranking time 0.
FEATURE MENU 1 EXPLANATION: J1-1. LOCK/UNLOCK TIMER Pre-set: After press arm/disarm, the door is locked/unlocked output 0.5 seconds. Variable1: After press arm/disarm, the door is locked/unlocked output 3.5 seconds. J1-2. LOCK TIMER Pre-set: same as J1. Variable 1: After press arm the door is locked output 15 seconds. Variable 2: After press arm the door is locked output 30 seconds. J1-3. UNLOCK PULSE Pre-set: After presses disarm the door is unlocked output one pulse.
J1-7. AUTO RE-ARM Pre-set: The system is disarming without ignition ON or open the door. After 30seconds, the system will arm itself without lock. Variable1: Delete this feature. Variable2: The system is disarming without ignition ON or open the door. After 30seconds, the system will arm itself with lock. J1-8.AUTOMATIC DOOR LOCK Pre-set: When the ignition turns from OFF to ON, doors will lock after 15 seconds. Variable1: When the ignition turns from OFF to ON, door will not lock.
J1-13. EMERGENCY OVERRIDE WAY Pre-set: simple way. Variable 1: 2 pin code way J1-14. DEFAULT SETTING Pre-set: Return the feature menu 1 to the factory set-up. FEATURE MENU 2 EXPLANATION: J2-1. ANTI CAR-HIJACKING Pre-set: Delete anti car-hijacking feature. Variable 1: Follow procedure to enter anti car-hijacking mode. J2-2. ANTI CAR-HIJACKING MODE SELECT Pre-set: entry anti car-hijacking way is mode C. Variable 1: entry anti car-hijacking way is mode B. Variable 2: entry anti car-hijacking way is mode A.
J2-4. PROGRAMMABLE L2 OUTPUT SELECT Pre-set: channel 2 output. Variable1: seconds unlock output. Variable2: channel 2 output and disarming Variable 3: output pulse before start. The wire will provide a 1 seconds -300mA pulsed ground output 1.5 seconds before the remote start unit activates as well as when the transmitter is used to unlock the system to prevent false triggering of the factory alarm when the remote start unit engages or when the system is used to unlock the doors. J2-5.
Variable1: Latched output: this selection will output a –300mA signal from the channel 1 output as soon as the channel 1 button is pressed and will continue until the button is pressed again. Variable2: Latched output/reset with ignition ON: this selection will output a –300mA signal from the channel 1 output as soon as the channel 1 button is pressed but will reset or stop when the ignition is turned ON.
J2-12. CHANNEL 3 OUTPUT MODE SELECT Pre-set: Momentary output: Anytime, within 3 seconds press button 4 once then press button 3 once, CH3 will output-300 mA Variable1: Latched output: this selection will output a –300mA signal from the channel 3 output as soon as the channel 3 button is pressed and will continue until the button is pressed again.
FEATURE MENU 3 EXPLANATION: J3-1. VEHICLE MODE Pre-set: Automatic gear car: Without ‘ready mode’, remote start directly Variable1: Manual gear car: The ‘ready mode’ routine has been completed successfully system can remote start J3-2. MANUAL GEAR CAR RESERVATION SETTING MODE Pre-set: Manual setting: When the engine running, press button 3+4 once to routine ‘ready mode’ Variable1: Auto pre-set setting: When the engine running exceed 10 seconds, ignition OFF will automatically routine ‘ready mode’ J3-3.
J3-7. GASOLINE ENGINE/DIESEL ENGINE Pre-set: Gasoline engine without wait-to-start light 2 seconds warm-up timer. Variable1: Diesel engine without wait-to-start light 15 seconds warm-up timer. Variable2: Diesel engine without wait-to-start light 30 seconds warm -up timer. Variable3: Diesel engine without wait-to-start light 45 seconds warm -up timer. J3-8. TIMER REMOTE START Pre-set: interval time is 12 hours in timer remote start. Variable1: interval time is 1 hour in timer remote start.
J3-13. CRANK TIME MODE OF TACHOMETER CHECKING TYPE Pre-set: the engine remote start detect tachometer signal is 4-cycle pulse of tachometer. Variable 1: the engine remote start detect tachometer signal is alterable by tachometer pulse frequency. Variable 2: the engine remote start detect tachometer signal is 2-cycle pulse of tachometer. J3-14. DEFAULT SETTING Pre-set: Return the feature menu 3 to the factory set-up.
INSTALLATION GUIDE FOR IDATALINK CONNECTED WITH AM9600 IDATALINK module (ADS-BLADE AL or ADS-BLADE TB) can be selected to work with AM9600 optional, the IDATALINK module can be used for bypass IMMOBILIZER SYSTEM for vehicle, and it can read RPM/DOOR/HAND BRAKE/FOOT BRAKE etc status, the IDATALINK module can remote control arm/disarm OEM alarm, it’s valuable for saving vehicle installation time.
1. download Weblink Updater software: http://www.idatalink.com/, select SUPPORT 2. 3. Install Weblink plug-in 4.1 program While the program has installed, then insert ADS-BLADE AL into AM9600, and make sure the connection is good. Then connect AM9600 (IDATA UPGRADE PORT) to PC through ”ADS-USB” (AM9600 do not need power supply) ──>then click Weblink plug-in 4.1 to download the software. 4. to start “ADS Plug in 4.
Then Download While download has finished, click “EXIT” 39
Installation guide: Please refer the installation manual, such as the above picture For example: model Maxima lntelli-key in the year of 05~08, the previous DOWNLOAD software can be matched with the vehicle and IMMOBILIZER BYPASS/ARM(DISARM) OEM ALARM/DOOR/HOOR/RPM function are supposed.
IDATA MODULE INSTALLATION DRAWING SLIPPED THE BUTTON HOURSING OF AM9600 1 RETURN THE HOURSING TO ORIGNAL STATUS 3 FIXED IDATA MODULE FIXED THE HOUSING 2 4 RX12 ANT OPTIONAL T35 RECEIVER VALET SWITCH T35 RECEIVER IDATA UPGRADE PORT LED CARTRIDGE CONNECTOR 30A FUSE FUSE BOX GND 30A FUSE 12V BATTERY RED +12V HANDBRAKE RED +12V GREEN HANDBRAKE PURPLE (START) YELLOW IGN1 ST AR ON AC C T OF F ORANGE ACC BROWN IGN2 FOOT BRAKE 10A FUSE BLACK/WHITE BRAKE +12V ORANGE -- LAMP INPUT LAMP
AM9600 INSTALLATION GUIDE CARTRIDGE CONNECTOR 1 NC NC 3 5 7 9 11 NC 13 15 17 19 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 RELAY (N.C) RELAY (COM) RELAY (N.
SK600 RX12 T35 RECEIVER OR OPTIONAL PC SETUP CABLE OPTIONAL SHOCK SENSOR IDATA UPGRADE PORT ANT T35 RECEIVER OPTIONAL CARTRIDGE CONNECTOR GREEN/WHITE (-) UNLOCK OUTPUT -300mA PC SETUP CABLE BLUE/WHITE (-) LOCK OUTPUT -300mA VALET SWITCH LED 30A FUSE FUSE BOX GND 30A FUSE 12V BATTERY OPTIONAL TEMPERATURE SENSOR RED +12V GREY/YELLOW DISARM IN + BORWN/YELLOW HOOD TRIGGER BROWN DOOR TRIGGER YELLOW IGNITION INPUT + GREY/WHITE ARM IN + BROWN/WHITE TRUNK TRIGGER BROWN/WHITE TRUNK TRIGGER- PURPLE (S
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This device complies with part 15 of the FCC rules.