GPS GPRS TRACKING AND ALARM SYSTEM HEU OPERATION & INSTALLATION MANUAL
REV: 2.8 (Standard, HEU-v4.0, HEU-I) I . BRIEF INTRODUCTION GPS GPRS Tracking and Alarm System utilize the GPS and car alarm functions in one unit. You can monitor the vehicle location and control the car alarm remotely. In addition, the unit will send event report if any trigger occurs. It has built-in 2 outputs and 5 inputs to perform essential alarm functions.
In addition, the system has a built-in rechargeable battery (12V 1.2A/H) for emergency use. The system will send an emergency “power cut” report when all of the external power is removed. User can check the external battery capacity status from the server. There system has another important security function-GPS Antenna Presence Detection. The system will send an emergency “GPS antenna failed” report when the GPS antenna is removed Waterproof casing design II.
III. PANEL INSTALLATION AND WIRING DIAGRAM RED GREEN YELLOW IV. STATUS INDICATOR The system has three statuses LED; the following is their corresponding description: Red: Power indicator. When the unit power on, the led will light all the time. Yellow: GPRS indicator. This LED will flash when the device received the signal of the GSM base station. Green: GPS indicator. This LED will turn continuously on when the unit received a valid GPS data.
Valet Switch LED: Button switch + LED diagram is listed below, including 2 Buttons and 1 LED. Button 2 LED Button 1 HEU valet switch operation. 2 buttons are defined as Button 1 and 2, please refer to the above diagram 1.) Self-Geofence: Press Button 1 once to activate self-Geofence. LED will be continuous ON. Press the button again to deactivate self-Geofence. LED will be OFF. 2.) Help button: Press Button 1 for 2 seconds: send HELP request message to the server. LED will flash 3 times. 3.
B. Version No. Checking The below interface will last until correct HEU Version No. is checked. (You should run this program before turn on power of HEU) C. MAIN INTERFACE 1.[User detail]: (1) Set Device ID for HEU. The device must be unique in order to be identified by the server. (2) Set Access Point Name (APN), User Name (GPRS), Password (GPRS). The maximum length of the APN, User name and Password is 49 characters.
2. [Geofence]: Setup the Geofence (in circular shape) parameters in this window. The format will be center of the Geofence and the related radius. User can also set the radius for the self-Geofence in this field. The self-Geofence can be activated/deactivated from the 2 button LED switch. 3.
In the working mode, the system will use the configurations as defined in this section. To activate the automatic report, please select “√” in checkbox and fill in data in the textbox. The reports will be summarized as (1) Intelligent report Parameters: On/Off, Report time when moving, Report time when stop, and Moving Speed (min. Speed is 0.1 km/Hr, max. Speed is 1000 km/Hr).
ALARM report Alarm report(s) is also configurable. User can customize the events generated by the in-vehicle input to be sent to the server. To enable the particular trigger reports by click the box. Sleep mode (when ACC OFF) (1) HEU can go to sleep mode when ACC goes off. (The average lasting time after ACC OFF is 5 minutes.) In sleep mode, both GPS & GPRS will be disabled. All the auto report (Time, Distance, Intelligent…) will not be send when ACC goes off.
Current (only GPS Sleep) Current (only GPRS Sleep) Current (Sleep & internal battery charge) Current (GPRS online) Current (GPRS transmission) Current (Peak) 30mA 21mA 3~10 mA 35~45mA (@24V) 70~80mA(@24V) 100~120mA(@24V) GPRS* * Data provided by Sony Ericsson Frequency Range (MHz) 900&1800 / 850&1900 models Channel spacing (Hz) 200 GPRS connectivity GPRS multi-slot class 8 GPRS mobile station class B SIM card interface 3V or 5V SMS storage Capacity 40 in ME Antenna Connector Built-in Antenna Impedance 50o
Communication GPRS \SMS Environmental Operating Temperature Storage Temperature -20°C to +55°C -40°C to +85°C Optional Accessories 1. Integrated Antenna for 900/1800 or 850/1900 MHz two types 2. External GPS Active Antenna 3. Valet Switch+LED Appendix II Event code summary GROUP A: (BASIC event) 101 Over the defined maximum speed limit 102 Self-diagnostic report 103 Course changes (direction changes) bigger than defined angles.
175 184 185 194 195 150 Enter defined Circular Geofence area7 Exit defined Circular Geofence area8 Enter defined Circular Geofence area8 Exit defined Circular Geofence area9 Enter defined Circular Geofence area9 Press Valet switch to send ‘Help’ request GROUP C In-vehicle INPUTS Event 253 (in-vehicle ACC) ACC on Example: The ‘EVENT 253’ will be generated and sent to the server when ACC is on. 254 (in-vehicle ACC) ACC off Example: The ‘EVENT 254’ will be generated and sent to the server.
Report Setup ACK event 502 Setup the Circular Geofence or Immediate Geofence parameters 505 Setup SMS telephone number. 507 Clear SMS date and max.
Installation drawing In Commercial Confidence 13
VII. Federal Communications Commission (FCC) Statement 7.1 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 7.2 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
9TH BUILDING, TONGFUYU INDUSTRIAL PARK, LONGHUA TOWN, BAOAN, SHENZHEN CITY, CHINA.
