GPS&GPRS TRACKING SYSTEM MODULE: GT3000X4 User Manual 08-03-2011 Version: 1.
1. INTRODUCTION GPS GPRS tracking system GT3000X4 utilize the GPS tracking function and basic car alarm control functions in one unit. You can monitor the vehicle location and control the car alarm remotely. In addition, the unit will send event report if any trigger occurs. It has built-in 4 outputs and 3 inputs to perform essential alarm functions. 1.
EEPROM and will not be lost even if the power is failure. Note that the device ID, GPRS APN name, GPRS login name and password need to be set in initial PC setup in order to make the connection to the server. All the reports configuration or Geo-fence setup can be changed at anytime via over the air commands. The automatic reporting mode can be categorized as ‘time’ report, ‘distance’ report, or ‘time & velocity’ report.
server if defined SMS number. All the stored report will be forward to the server when GPRS connection is completed next time. 1.5 TCP AND UDP SOCKET SUPPORT GT3000X4 supports both UDP and TCP socket communication. The server IP, port number and socket type can be selected from the PC-setup program or remote server command. In addition, the connection can be swap over to any server IP or port (either UDP or TCP) via the air command. 1.
(2) Activate or deactivate Immediate Geo-fence Press the button and release it when the LED flashes once. After releasing it, the LED will stay continuously on to indicate the ‘Immediate Geo-fence’ is on. To deactivate: Press the button (the LED will be temporally off), and release it when the LED flashes once. After releasing it, the LED will then stay continuously off. A report will be sent out if the vehicle goes out/in to the Geo-fence zone.
Keep alive procedure (in order keep connection in GPRS network, the unit can be set to send short keep alive report to the server in order to prevent the disconnection from the mobile service provider) 1.12 AIR DOWAND User can via OTA to update firmware for the main unit. I. BASIC FUNCTIONS FUNCTIONS APPLICATIONS GPS GPS receiver will output a complete position, velocity, and time (PVT) solution in the NMEA Version 3.0 protocol GPRS, SMS GPRS use standard TCP or UDP communicate protocol.
Keep alive report Event Report Temperature report Speeding report Low battery report Geo-fence trigger report ALARM trigger report, e.g. ignition inputs, etc … History data store 3000 report can be saved in unit, and read from server and pc-setup II. STATUS INDICATOR SYSTEM LED: RED: Power indicator. When the unit power on, the led will light all the time. When power cut off the unit works with backup battery, the led will flash until all the report is sent to server. YELLOW: GSM/GPRS indicator.
A. LOGIN DIALOG WINDOW Select the correct COM port number, then “reset” the unit by pressing the reset button, and next click “OK”. Note that: it is necessary to power on and reset the device soon after click the “ok” button. PC setup program will detect the hardware for 60 seconds. If no hardware is detected, it will exit. During the opening up screen shown as below, user can press “Esc” key to terminate the program. B. VERSION NO. CHECKING The below interface will last until correct UNIT Version No.
(1) IMPORTANT INFORMATION SIM PIN: If the SIM card is password protected, user can input the “SIM PIN” window to set password of SIM Card. IMEI: Any operate with ‘request or request all’ after GPRS power on, the module series number will display automatically, otherwise it displayed with space. Device ID/Device password: Set UNIT ID and UNIT password for the device.
(2) INTERNET LOGIN INFORMATION Set Access Point Name (APN), User Name, Password. The maximum length of the APN, User name and Password is 49 characters. (3) SERVER INFORMATION TCP/UDP address and Port number of the remote server being set, UNIT will send report to these addresses. Note that only one TCP or UDP server will be used at the same time. Monitor center phone: Set the SMS Number of the server. The unit will send reports to the server if GPRS connection is failed.
3D GPS fix only: the report will be display “A” in the report and indicate that if the number of satellite is more than 4 or equal to 4. If the number of satellite is less than 4, then it will show “L” in GPS fixes section. 2D and 3D GPS fix display: the report will be display “A” in the report and indicate that if the number of satellite is more than 4 or equal to 4. If the number of satellite is equal to 3, then the report will show “B” in GPS fix section.
Apply All: transfer the whole setting to GT3000X4. Initialize: clear all data in UNIT. Note that Device ID, GPRS Login and server IP/Port information need to be input correctly in order to make the connection. If the report sending using GPRS connection fails, the report will be sent to the ‘primary’ SMS number first. The report will be resent, when the GPRS connection becomes available. 2.
1) GPRS always online Parameters: Reconnect interval While using this mode, when the unit can not searched GPRS signal, system will reconnect GPRS interval a preset value. (e.g.: 1minute) 2) Based on report mode Parameters: Max. reconnect times, reconnect interval While using this mode, the unit will connect to the server when there is a report to send. If the first connection is failed, it will retry to connect to the server up to the max. reconnect times.
Parameters: On/Off, and interval / retry times. In order to keep connection in GPRS network, the unit can be set to send short keep alive report to the server in order to prevent the disconnection from the mobile service provider. Send reports after a successful keep alive ACK. Parameters: On/Off. If you select this function, all the reports will only be sent out after a successful keep alive ACK. (So if your keep alive time is shorter then select this function will be OK.
3. [REPORTS:] 3.1 FIXED REPORTS (1) INTELLIGENT HISTORY REPORT (RECORD THE REPORT IN THE SYSTEM’S FLASH RAM) Parameters: On/Off, Report time when moving, Report time when stop, and threshold speed. (Min. speed is 0.1 km/Hr, max. speed is 1000 km/Hr).
(2)-a Local: Enable this item; fix time reports will be sent in local mode. Roaming: Enable this item, fix time reports will be sent in roaming mode. Otherwise, fix time reports will be saved in memory and be sent to server when comeback to local mode. SMS: If this checkbox is selected, fix time reports will be sent through SMS when GPRS is not available. There are two ways to distinguish unit in moving/stopped conditions: a.
The vehicle will send a stopped report every 10minutes when vehicle is stopping. (3) FIXED DISTANCE REPORT Parameters: On/Off, and distance. (Min. distance is 0.1 km, max. distance is 100 km). If fill the above data in the textbox, then: The vehicle will send a distance report every 3km when vehicle is moving. 3.
Parameters: On/Off, and min. and max. temperature. Set the report will send in local or roaming or through SMS, max./ min. temperature, temperature unit. (2) I/O STATUS REPORT Local: Enable this item; fix time reports will be sent in local mode. Roaming: Enable this item, fix time reports will be sent in roaming mode. Otherwise, fix time reports will be saved in memory and be sent to server when comeback to local mode.
(4) COURSE CHANGE REPORT Enable this item to send a report when the course change is bigger than the value set here (5) BATTERY REPORT Enable this item to send a report when the external battery level is low The system will ignore the parameter with a value ‘0’ to prevent continuous non-stop reporting. (6) STOP REPORT While the vehicle speed less than ‘5km’ and more than 120 seconds, the unit will send a stop report to server. 4.
(1) CIRUCLAR TYPE ORIGIN FORMAT Four Circular Geofence and one self-geofence: Circular Geofence must set origin and radius: Origin format :N2446.5321E12120.4231; N2446.5321 is latitude, E12120.4231 is longitude.
Radius from 0.1 km to 1000km. (2) RECTANGULAR TYPE FORMAT Five rectangular geofence: Set two points position, the point format is N2446.5321E12120.4231; With two points, generate one rectangle. Unit will detect whether in rectangle. When unit enter or leave rectangle, will send one message out.
20 point Geo-fence areas can be set. When UNIT is out of these predefined zones, a report will be generated.
APPENDIX GT3000X4 SPECIFICATIONS PHYSICAL PARAMETERS Enclosure dimensions 88(L)*76(W)*25(H) Unit Weight About 100g ELECTRICAL DC Supply voltage 12V OR 24V DC Tolerance voltage 9V－36V Current (GPRS online) 50mA GPRS Frequency Range (MHz) (Be used in GT3000X4-BJ) 850/900/1800/1900 GPRS connectivity GPRS multi-slot class 10 GPRS mobile station class B SIM card interface 1.8V/3.
Hot start 1 ＜1s Warm start 2 ＜35s Cold 3 ＜35s Standard GPS software NMEA message switchable GGA, GSA GSV, VTG, RMC, GLL COMMUNICATION GPRS \SMS\USB BATTERY Build-in backup battery Li-Ion 300mAH ENVIRONMENTAL Operating Temperature -20°C to +55°C Storage Temperature -40°C to +85°C ACCESSORIES 1. 2. 3. 4. 5. 6. 7. Main unit Operation manual Wire harness GSM Antenna GPS Antenna Valet switch (SW-2) LED (LD-4) OPTIONAL ACCESSORIES 1. 2. 3. 4.
NOTE: Using wrench to tighten the screw cap of GPS and GPRS antenna and lock the screw cap to fix position, for avoid antenna connect abnormality, user can not using hands to tighten the screw cap. VI. Federal Communications Commission (FCC) Statement 1) You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. VII Operation is subject to the following two conditions: 1) This device may not cause interference and 2) This device must accept any interference, including interference that may cause undesired operation of the device.
2-PIN CONNECTOR FOR GPRS/GPS ANT DETECTED GSM ANT RED LED--POWER INDICATOR GPS ANT GREEN LED--GPS INDICATOR YELLOW LED--GPRS INDICATOR PC SETUP BATTERY PORT OPTIONAL RELAY 5 6 7 8 GREEN 86 RED RED 87 30 ORANGE 85 RELAY 1 2 3 4 BLACK GND 4. PURPLE--TRUNK Fuse 5A RED BATTERY OPTIONAL HORN RELAY RELAY 8. WHITE/RED 86 85 87a 30 OPTIONAL RED +12 V RED 85 30 86 87 WHITE ORANGE CH1 12V or 24V BATTERY RELAY +12 V TRUNK Fuse Box GREEN 3.
FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.
