GPS&GPRS CAR ALARM SYSTEM Model: GT3200 OPERATION & INSTALLATION MANUAL ! REV:2.
INTRODUCTION GPS GPRS Tracking and Alarm System utilize the GPS and car alarm functions in one unit. You can monitor the vehicle location and control the car alarm remotely. In addition, the unit will send event report if any trigger occurs. It has built-in 8 outputs and 9 inputs to perform essential alarm functions. 1.
The event trigger report is also configurable. User can turn on or off any event generated report from the PC setup program or via the air command. The event triggered report include (1) In-vehicle Door close/open (2) In-vehicle ignition on/off (3) Temperature range in/out the preset range (4) In-vehicle shock sensor trigger. The build in alarm (optional) trigger reports are also configurable and can be set from PC setup program or air command.
3. Enable anti-car jacking: (can be performed at any time) If Server send anti-car jacking command, the system will enter anti-carjacking mode after the unit received the command. Enter the anti-carjacking mode, the first 30 seconds countdown, The horn will sound once and parking lights will flash once every 10 seconds, after 30 seconds, horn will sound once and parking lights will flash once every 5 seconds, 30 seconds later, horn will sound and parking lights will flash once every 1 second.
GT3200 Can go to sleep mode when ACC goes off, Shock-sensor not be trigger for 5minuts and this feature is configurable. “GPS” can be power off. User can setup the automatically wakeup time during the sleep mode to ensure the device is working. The system can send out a diagnostic report to the server after waking up. During the sleep mode, if any of the inputs are triggered, the system will wake up and send relevant reports to the server. The input triggers for waking the device up are selectable.
Valet Switch (1) Send help report and enter the monitor mode (2) activate or deactivate Immediate Geofence (3) Activate panic mode (4) sending ‘Duty on’ or ‘Duty off’ report to the server (5) Emergency release to exit ‘ARM’, ‘Anti-carjacking’ or ‘Panic’ modes (6) code learning for build in alarm, (7) set valet mode for build in alarm 2-button keypad (1) “II” Hang up a phone (2) “I” Answer a phone 1. SMS send/receive 2. Phone call 3. Main unit information display Handset (Optional) 4.
IRKP-20 is an external wireless 20- key keypad to used for calling. Anytime the unit can call out and pick up phone call as well. There are two ways to call out: 1) to dial the number directly through the keypad; 2) press shortcut key to call the preset telephone number defined by PC setup software. a. After dialing the telephone number, press button once or button〝Ⅰ〞of two button valet switch once dial out.
(4) ‘Duty on’ or ‘Duty off’ reports / ‘Status on’ Status off’ reports Press the button (the LED will be temporally stay off) and release it when the LED flashes 3 times. After releasing it, a ‘Duty on’ report will be sent out. To deactivate: Press the button (the LED will be temporally stay off) and release it when the LED flashes 3 times. After releasing it, a ‘Duty off’ report will be sent out. (5) Emergency release to exit ‘ARM’, ‘Anti-carjacking’ or ‘Panic’ modes.
A. LOGIN dialog window Select the correct COM port number, then “reset” the unit by pressing the reset button, and next click “OK”. Note that: it is necessary to power on and reset the device soon after click the “ok” button. PC setup program will detect the hardware for 60 seconds. If no hardware is detected, it will exit. During the opening up screen shown as below, user can press “Esc” key to terminate the program. B. Version No. Checking The below interface will last until correct UNIT Version No.
C. MAIN INTERFACE 1. [User detail:] If the SIM card is password protected, user can input the “SIM PIN” window to set password of SIM Card. IMEI: Any operate with ‘request or request all’ after GPRS power on, the module series number will display automatically, otherwise it displayed with space. Set UNIT ID and UNIT password for the device.
Set Access Point Name (APN), User Name, Password. The maximum length of the APN, User name and Password is 49 characters. TCP/UDP address and Port number of the remote server being set, UNIT will send report to these address. Note that only one TCP or UDP server will be used at the same time. To select enable or disable local GPRS/SMS or Roam GPRS/SMS After unit exited PC-SETUP, user can select GSM or GPS debug information output by hyper-terminal. Note: The baud rate of Hyper-terminal must be correct.
The unit has speed-dialing button PC setup software. of change with SIM card, the speed dialing number can preset by AUTO GPS fix: the report will be display “A” in the report and indicate that if the number of satellite is more than 3 or equal to 3. If the number of satellite is less than 3, then it will show “L” in GPS fix section. 3D GPS fix only: the report will be display “A” in the report and indicate that if the number of satellite is more than 4 or equal to 4.
2. [Geofence:] Four Circular Geofence and one self-geofence: Circular Geofence must set origin and radius: Origin format :N2446.5321E12120.4231; N2446.5321 is latitude, E12120.4231 is longitude. Radius from 0.1 km to 1000km. User can set the reports send or local or ignore: Send: report will send out immediately if generation Local: report will save if generation, it will send out by local network Ignore: cancel reports.
Five rectangular geofence: Set two points position, the point format is N2446.5321E12120.4231; With two points, generate one rectangle. Unit will detect whether in rectangle. When unit enter or leave rectangle, will send one message out. 20 point Geo-fence areas can be set. When UNIT is out of these predefined zones, a report will be generated.
3. [Local report]: Automatic report can be configured in this section. To activate the function(s), please select “√” in checkbox and fill in data in the textbox. The reports will be summarized as (1)Intelligent report Parameters: On/Off, Report time when moving, Report time when stop, and threshold speed. Report when speed less than a preset value (refer the following 1.5 Km/Hr), and it will send stop report after a preset time (refer the following 120Sec). (min. speed is 0.1 km/Hr, max.
(3)IO connect selection Parameters: to select either temperature sensor or AD1 (4)Temperature report Parameters: On/Off, and min. and max. temperature.
[on/off] SEND REPORT IF ADC2 LESS THAN [min voltage] V for [debounce time] SEC, RESEND PER [resend time] SEC [on/off] SEND REPORT IF ADC2 MORE THAN [max voltage] V for [debounce time] SEC, RESEND PER [resend time] SEC [on/off] SEND REPORT IF ADC2 GO UP [up voltage] V for [debounce time] SEC [on/off] SEND REPORT IF ADC2 GO DOWN [down voltage] V for [debounce time] SEC [on/off] SEND REPORT IF ADC2 ENTER/EXIT [min voltage] V TO [max voltage] V for [debounce time] SEC Note: AD2 input voltage range is 0~3.
Parameters: resend interval, threshold speed, over speed delay time, exit over speed delay time, alert when over speed and report send or ignore For example, if resend interval is 20 sec, enter over speed delay time is 20 sec, threshold speed is 110Km/h and exit over speed delay time is 2 sec. If vehicle speed over threshold speed 20seconds, system will send speed over report once interval 20 sec until exit speed over delay time 2 sec, the over speed report will stop to send.
3) GPRS connect once While using this mode, the unit will connect to the server when there is a report to send (but only try once). If it is not successful, the report will be stored and sent out in the next successful connection. Disconnect GPRS connection when report sending is completed. 4) Reduce dialup attempts Parameters: On/Off, Max. reconnect times, connect delay If this method is used, the unit will reduce dialup attempts when attempting to reconnect more than reconnect times.
4. [Roam report] All the roam reports configured are same as Local report. Send: report will send out immediately if generation Local: report will save if generation, it will send out by local network Ignore: cancel reports. 5.
Alarm report(s) is also configurable. User can customize the events generated by the in-vehicle input or build in car alarm to be sent to the server. If the item(s) be selected (VALID), the related reports will be sent. Otherwise the report will be ignored even when an event is occurred internally. Also build in car alarm function can be set on here. If input 3 with distance is selected, system will send the distance report every time ACC ON to ACC OFF, for example: %%GT3200,A,070521024400,N2240.8929E11359.
If select the item, when ACC off, system will cut power of handset, otherwise, system will not cut power of handset. Parameter: on/off, kilometer When acc off, unit will lock GPS, the kilometer is the radius of protecting vehicles, if vehicle moved away the range, unit will unlock GPS. 6.
7. [Roam setting] 1) Roaming GPRS mode User can configure roaming GPRS mode with automatic register or manual register in this field. When roaming GPRS mode in manual register, user can set 20 prefer operators, main unit will search and register from the 20 prefer operators.
2) Compress setting 1. 2. 3. 4. To send report in local GPRS, compressing N reports to a packet and then send out.(N: the digit between 1~8) To send report in roam GPRS, compressing N reports to a packet and then send out.(N: the digit between 1~8) To send report in local SMS, compressing N reports to a SMS and then send out.(N: the digit between 1~5) To send report in roam SMS, compressing N reports to a SMS and then send out.
GPRS* Frequency Range (MHz) (Be used in GT3200MT/ GT3200FT/GT3200ST) 850/900/1800/1900 Frequency Range (MHz) GPRS* (Be used in GT3200XT) 900&1800&1900 or 850&1800&1900 GPRS connectivity (Be used in GT3200MT/ GT3200FT/GT3200XT/GT3200ST) GPRS multi-slot class 10 GPRS mobile station class B SIM card interface (Be used in GT3200ST) 1.8V/3.
Optional Accessories 1. Car alarm 2. Combined Antenna (with GPRS and active GPS) 3. Temperature sensor 4. Ultrasonic sensor 5. Shock-sensor 6. Crash sensor 7. PC-setup Cable 8. Handset 9. Hand free 10. Microphone 11. 2-Keypad Note: Using wrench to tighten the screw cap of GPS and GPRS antenna and lock the screw cap to fix position, for avoid antenna connect abnormality, user can not using hands to tighten the screw cap.
OPTIONAL HANDSET OPTIONAL TEMPERATURE SENSOR OPTIONAL TEMP SENSOR OPTIONAL HANDSET OPTIONAL CRASH SENSOR OPTIONAL HANDFREE OPTIONAL HANDFREE OPTIONAL CRASH SENSOR OPTIONAL MIC OPTIONAL PC SETUP CABLE RESET OPTIONAL EXTERNAL RF ANT OPTIONAL MIC H8 H7 H9 H10 H11 H12 H13 GREEN LED: GPS INDICATOR YELLOW LED: GSM INDICATOR RED LED: POWER INDICATOR H1 H2 H3 H4 H5 H6 GPS ANT GSM ANT VALET SWITCH LED 5A FUSE OPTIONAL SHOCK SENSOR RED BLACK II 12V or 24V BATTERY I OPTIONAL 2-KEYPAD OPTIONAL
15.21 Federal Communications Commission (FCC) Statement You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
