GPS&GPRS TRACKING SYSTEM GT3100 OPERATION/INSTALLER MANUAL
REV: 2.0 (GT3100-special, V1.51, GT500-SIM340.C1) I. INTRODUCTION PORTMAN GPS GPRS tracking system GT3100 utilize the GPS tracking function and car alarm functions in one unit. You can monitor the vehicle location and control the car alarm remotely. In addition, the unit will send event report if any trigger occurs. It has built-in 8 outputs and 5 inputs to perform essential alarm functions. 1.
1.3 Geo-fence function The device has built-in 30 Geo-fence sets (1 immediate Geo-fence, 4 circular, 5 rectangular and 20 point); it will send the report to the server if the Geo-fence event is triggered. User can setup the Geo-fence area from the PC setup program or sending the defined. A unique immediate Geo-fence function: ‘Immediate-Geo-fence function’ is a circular type Geo-fence that can be activated or deactivated from a single button.
1.7 Valet switch operation User can use the supplied Valet switch to perform 5 essential tasks, including (1) sending help report (2) activate or deactivate Immediate Geo-fence (3) sending ‘Duty on’ or ‘Duty off’ report to the server (4) Emergency release to exit ‘ARM’, ‘Anti-carjacking’ or ‘Panic’ modes (1) Sending ‘HELP’ report Press the button once, The LED will flash once and a ‘HELP’ report will be generated.
II. BASIC FUNCTIONS FUNCTIONS APPLICATIONS GPS GPRS, SMS GPS receiver will output a complete position, velocity, and time (PVT) solution in the NMEA Version 3.0 protocol GPRS use standard TCP or UDP communicate protocol. If the GPRS service is failed, the SMS mode will be turned on for emergency use. In-vehicle Door. 5 input In-vehicle ACC Temperature sensor port (optional) Valet switch port 1. Parking light (-300mA) 2. Door Lock (-300mA) 3. Door Unlock (-300mA) 8 output 4.
III. PANEL INSTALLATION AND WIRING DIAGRAM Horn Siren output output 12 1 2 Siren/Horn output select Jumper I/O Power Port GPS Output 9 GPS Antenna 10 8 7 Temperature GSM Sensor Antenna 3 6 PC SETUP GPRS/GPS/POWER STATUS LED 11 SIM CARD 1.) 2.) 3.) 4.) 5.) 6.) 7.) 8.) In-vehicle I/O and power port: for in-vehicle I/O, and power, etc …. GPS output port: white 2-pin connector. VALET switch port: white 2-pin mini connector.
9.) GPS antenna: female SMA.. 10.) System LED: RED- Power indicator; Green- GPS indicator, Yellow- GSM indicator. Warning! Power off the system until the Red LED completely turns off before unplug or insert the SIM card. Otherwise, it may damage your SIM card. 11.) SIM CARD. 12.) Siren or Horn output select jumper. IV. STATUS INDICATOR System LED: RED: Power indicator. When the unit power on, the led will light all the time.
C. MAIN INTERFACE 1. [User detail:] If the SIM card is password protected, user can input the “SIM PIN” window to set password of SIM Card. Set UNIT ID for the device.
Set Access Point Name (APN), User Name, Password. The maximum length of the APN, User name and Password is 49 characters. TCP/UDP address and Port number of the remote server being set, UNIT will send report to these address. Note that only one TCP or UDP server will be used at the same time. Set the SMS Number of the server. The unit will send reports to the server if GPRS connection is failed. UNIT can save 900 reports (900-1) recently; Click ‘Export’ button can export them with Excel or Text format.
2. [Geo-fence:] 4 circular, 5 rectangle and 20 point Geo-fence areas can be set. When UNIT is out of these predefined zones, a report will be generated. When self Geo-fence is activated, It will record the current position as the origin and use the predefined distance for the radius to enable a circular Geo-fence. Origin\Upright point\Downright point has the format: N2446.5321E12120.4231 (21 fixed digits) Radius has the format: User can input the circular radius from 0.1 to 1000 (in km). 3.
The reports will be summarized as (1)Intelligent report Parameters: On/Off, Report time when moving, Report time when stop, and threshold speed. (min. speed is 0.1 km/Hr, max. speed is 1000 km/Hr). (2)Intelligent history report (record the report in the system’s flash ram) Parameters: On/Off, Report time when moving, Report time when stop, and threshold speed. (min. speed is 0.1 km/Hr, max. speed is 1000 km/Hr). (3)Fixed time report Parameters: On/Off, and time.
Simulate Click this buttons, it will base on the configurations to generate an approximate maximum dial-up numbers within 24 hrs. Therefore, user can predict the worst case dial-up connection if the server link is dead or GPRS disconnected. Special command for SMS mode: If the GT3100 is not in the GPRS online status, user can send command &&Y02 or &&Y04 to ask unit to connect to server.
APPENDIX GT3100 SPECIFICATIONS Physical Parameters Enclosure dimensions 88(L)*76(W)*25(H) Weight 100g Electrical DC Supply voltage 12V DC Tolerance voltage 9V－16V Current (GPRS online) 60mA Current (GPRS transmission) 80mA Current (Peak) 120mA GPRS* Frequency Range (MHz) Support 4-frequency 850/900/1800/1900 Channel spacing (Hz) 200 GPRS connectivity GPRS multi-slot class 8 GPRS mobile station class B SIM card interface 3V/5V SMS storage Capacity 40 in ME Antenna Connector Silver Ma
Communication GPRS \SMS\RS232 Environmental Operating Temperature -20°C to +55°C Storage Temperature -40°C to +85°C Accessories 1. Main unit 2. Operation/installer manual 3. Wire harness 4. GSM Antenna 5. GPS Antenna 6. Starter kill relay (RL-100) 7. Valet switch (SW-2) 8. LED (LD-4) Optional Accessories 1. Built in 20mA/H Ni-Mh 4.8V backup battery (optional) 2. Combined Antenna (with GPRS and active GPS) 900/1800 and 850/1900 MHz two types (optional) 3. GPS Active Antenna (optional) 4.
Fuse Box OPTIONAL TEMPERATURE SENSOR Fuse 5A +12V 85 30 87 86 PC SETUP GPS ANTENNA SIREN/HORN OUTPUT SELECT JUMPER GSM ANTENNA RED BLACK WHITE/RED PURPLE ORANGE GT3100 RESET BUTTON GPS SIGNAL OUTPUT BROWN GRAY YELLOW WHITE LED VALET SWITCH + DOOR TG- - RELAY +12V FUEL PUMP DOOR TG+ OFF ACC ON START GREEN (-)UNLOCK/(+)LOCK OUTPUT BLUE (-)LOCK/(+)UNLOCK OUTPUT GREEN/BLACK CH2 OUTPUT -300mA 14 INSTALLATION GUIDE MODE:GT3100 Horn +12V RELAY 1N5401 1N5401 86 85 87a 30 12V BA
VI. Federal Communications Commission (FCC) Statement 1) You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 2) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
