User's Manual

ManualsBrandsPolygroup ManualsElectronicsLow voltage quick set tree with remote controller

1. Before you start to assemble your tree, choose an appropriate location near a wall outlet.

2. Assemble the tree stand and place on a level surface. (See Fig. A)

Congratulations on purchasing your new tree from

Polytree®! This tree assmebles with Quick Set®

technology -Set up and light up your tree in less than 10 minutes! Carefully follow the instructions below

on how to quickly and easily set up your new tree.

TREE ASSEMBLY INSTRUCTIONS

Top view

Side view

Fig. C

ASSEMBLY INSTRUCTIONS

MADE IN CHINA

3. Each tree section is numbered with a tag. Please identify all sections before assembling.

4. Assemble the tree from the bottom to the top. Start with the bottom section and remove protective

cap before inserting into the assembled stand. Make sure the pole is firmly inserted and secured into

the stand.

5. Please remove protective cap from middle section(s) and continue inserting into the bottom section

until the tree top is inserted.

6. Allow branches to fall into place or gently pull up and out. When adjusting branches, be sure that all

wires are free of branch hinges.

7. Insert green label extension cord plug into the wall outlet (see Fig. B ), your entire tree should now be

lit. If some bulbs do not light or flicker, search for any loose plugs and/or broken, loose or missing

bulbs. Connect the plugs or replace the bad bulbs promptly in order to maintain the performance and

life expectancy of your pre-lit tree.

Begin to shape the branches and tips working from the bottom to the top. Start with tips farthest from

the pole and fan out one to the right, one to the left and one at the center of the main stem. (See Fig. C)

9. After shaping the entire tree following the previous step, slightly upsweep all branch tips for a uniform

look. Shift branches to fill any gaps. Your Christmas tree is now complete and ready to be decorated.

MODEL #: XXXXXX

*Electrical Rating For The Tree

(For Indoor Use Only)

Input:100-240VAC, 50/60Hz, 0.5A Max.

Output: 29V DC 0.5A

Fig. B - Tree and Light Assembly

Power Cord

to Wall Outlet

On/Off Switch

Section 1

Section 2

Section 3

50S

100S

50S

100S

Control box

100S

Do Not Tamper

Internal Parts

Remove the

protective cap

Do Not Tamper

Internal Parts

Remove the

protective cap

Fig. A - Tree Stand Assembly

Slide the legs upwards into slots at the base

of the trunk and tap lightly with hammer

until firmly fixed.

On/Off

Switch

Summary of content (4 pages)

PAGE 1
Congratulations on purchasing your new tree from Polytree®! This tree assmebles with Quick Set® technology -Set up and light up your tree in less than 10 minutes! Carefully follow the instructions below on how to quickly and easily set up your new tree. 1. Before you start to assemble your tree, choose an appropriate location near a wall outlet. 2. Assemble the tree stand and place on a level surface. (See Fig. A) Fig.
PAGE 2
1. Unplug extension cord from the wall outlet first and then remove all ornaments and decorations. 2. Disassemble the tree from the top to the bottom. Start with the tree top and gently lift straight up to remove from section below and fold all branches toward the pole. 3. Continue by gently lifting straight up each section(s) from the section below and fold all branches toward the pole until the bottom section is removed from the tree stand.
PAGE 3
READ AND FOLLOW ALL SAFETY INSTRUCTIONS. a. b. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation. c. This seasonal product is not intended for permanent installation or use. d.
PAGE 4
HOW TO USE THE DUAL COLOR LIGHT CONTROLLER AND REMOTE CONTROL: Press the selector button on the “Dual Color Light Controller” or “Remote Controller” to select among: (1) CLEAR AND MULTI-COLOR ALTERNATING; (2) CLEAR LIGHTS; (3) MULTI LIGHTS and (4) TURN OFF BOTH LIGHTS. Remote Note: The lights will be automatically reset to “CLEAR AND Controller MULTI-COLOR ALTERNATING” every time the product is powered up. For the remote controller, replace only with CR2032 battery.