Troubleshooting Tips

ManualsBrandsPolygroup Evergreen ManualsElectronicsRemote Controller

ASSEMBLY INSTRUCTIONS

MADE IN CHINA

1 2

ASSEMBLY INSTRUCTIONS

MADE IN CHINA

ASSEMBLY INSTRUCTIONS

MADE IN CHINA

Thank you for purchasing your Christmas tree. The instructions below will help you quickly and easily set up

your new tree.

1. Find a level surface near an electrical outlet and assemble the tree stand as shown in Fig. A.

Fig. D

CAUTION

1. To reduce the risk of fire and electric shock:

a) Use only the power supply that was provided with this product. Using a different adapter will damage the

lights and may cause fire, or electrical shock hazards.

b) Do not install on trees having needles, leaves or branch coverings of metal or materials which look like metal.

c) Do not mount or support strings in a manner that can cut or damage wire insulation.

2. The controller and remote controller (if included) can only be used with this product.

REMOTE CONTROL INSTRUCTIONS

In case the light motion effects keep switching to the next one every 30 seconds

and continues to cycle, this means the Demo mode is on.

To cancel the Demo mode, simply press and hold the (Brightness Down) button

and the (Slower Speed) button together for 10 seconds.

NOTE:

1. Slide open the battery cover.

2. Replace with a new CR2032 button cell battery with

correct polarities (+/-) as indicated.

3. Slide the battery cover closed.

Battery Replacement

Remove insulation

tab before use.

Battery Cover

WARNING

1. Small parts, keep away from children.

2. Do not expose the product to moisture.

3. Remove batteries when not used for an extended period of time,

or when depleted.

4. Dispose of used batteries properly, and local laws and

regulations regarding the disposal of hazardous waste.

5. Use only CR2032 batteries for the remote controller.

6. Clean the battery contact surfaces gently prior to battery installation.

7. Do not dispose of batteries in fire. Batteries may explode or leak.

8. This product is powered by a lithium battery. Due to their small size,

lithium batteries can easily be swallowed by children. Ingestion of

such batteries has been known to cause death.

9. This is a lithium battery which if swallowed has been known to cause death.

WARNING: This product may potentially trigger seizures for people with photosensitive epilepsy when using the

motion effect light modes.

ON/OFF

Multi Color Steady Glow

Color Wheel

Faster Light Effect For

Preset Motion

Slower Light Effect For

Preset Motion

Previous Preset Motion Effect

Customizable color selection

Warm White Steady Glow

Brightness Up

Next Preset Motion Effect

Brightness Down

Tap to display all lights in

multi color steady glow

Tap to display all lights in

warm white steady glow

Tap or to select from the

10 preset motion effects:

• Fading

• Multicolor Ball

• Color-Changing

• Collision

• Fireworks

• Falling Rings

• Twinkle

• 3-Ring Motion

• Rainbow Shower

• Rainbow

2. Identify all tree sections (See Fig. B) by the tags on them, and start assembling from bottom to top.

3. Insert the pole into the stand. Allow all branches fall down into place. Check to make sure that all wires are

free from branch hinges.

4. Shape the tree section one branch at a time. Start with the tips closest to the pole and move outwards.

Fan all the tips out in alternating directions, and slightly upsweep them for a natural look (See Fig. C).

Top view

Side view

Fig. C

TROUBLESHOOTING TIPS

If Tree Does Not Illuminate / Some Bulbs Do Not Light or Flicker

1. Please check to make sure that all plugs are properly connected and adapter is plugged into the wall outlet.

2. Turn the poles gently to make sure pole to pole sections are connected properly

3. Check for loose connection between light string plugs and extension cords.

1. Extra hinge pins are included for repairing the hinges of the

branches. Place the branch into the slot of the bracket.

2. Insert a new hinge pin through the hole and secure using the

retainer washer. (See Fig. D)

Loose Hinge Pin

STORAGE INSTRUCTIONS

1. Unplug adapter from the wall outlet first and then remove all ornaments and decorations.

2. Disassemble the tree from the top to the bottom. Start with the tree top and gently lift straight up to remove

from section below and fold all branches toward the pole.

3. Continue by gently lifting each section straight up from the section below. Fold all branches toward the pole

until the bottom section is removed from the tree stand.

4. Carefully place all tree sections into the storage bags within the shipping box(es) and tape the box(es) shut.

5. When not in use, please store your tree in a cool, dry place away from sunlight. Exposing your tree to

excessive heat or humidity may damage your tree.

5. Repeat Step 4 and 5 for the upper tree section(s) until tree top is installed and shaped.

6. Connect plug with adapter, and plug it in to the wall outlet as indicated in Fig. B.

7. Step back and view your tree. Shift branches to fill any gaps. Your Christmas tree is now ready to be decorated.

This tree includes spare hinge pins and washers.

SPARE PARTS

LIGHT ASSEMBLY DIAGRAM

ITEM #: TG60P4525D02

48 Watts

Fig. A - Tree Stand Assembly

1. Pull apart the legs of the stand so that

they are x-shaped.

2. When inserting the bottom section of

the tree into the assembled stand,

thread the eyebolt into the stand and

tighten until the pole is firmly secured.

Eye Bolt

*Electrical Rating For The Tree

(For Indoor Use Only)

Input: AC 120V, 60Hz, 0.83A

Output: DC 24V, 2A

Controller:2A

Fig. B - Tree and Lights Assembly

Align both arrows

in a straight line

before sliding

down to insert

Do Not Tamper

Internal Parts

Plug Adapter

Into Wall

Outlet

Summary of content (5 pages)

PAGE 1
48 Watts Thank you for purchasing your Christmas tree. The instructions below will help you quickly and easily set up your new tree. 1. Find a level surface near an electrical outlet and assemble the tree stand as shown in Fig. A. Fig. A - Tree Stand Assembly 1. Pull apart the legs of the stand so that they are x-shaped. Eye Bolt 2. When inserting the bottom section of the tree into the assembled stand, thread the eyebolt into the stand and tighten until the pole is firmly secured.
PAGE 2
3. Insert the pole into the stand. Allow all branches fall down into place. Check to make sure that all wires are free from branch hinges. 4. Shape the tree section one branch at a time. Start with the tips closest to the pole and move outwards. Fan all the tips out in alternating directions, and slightly upsweep them for a natural look (See Fig. C). Fig. C Top view Side view 5. Repeat Step 4 and 5 for the upper tree section(s) until tree top is installed and shaped. 6.
PAGE 3
ON/OFF Warm White Steady Glow Multi Color Steady Glow Tap to display all lights in warm white steady glow Tap to display all lights in multi color steady glow Color Wheel Customizable color selection Faster Light Effect For Preset Motion Next Preset Motion Effect Brightness Up Slower Light Effect For Preset Motion Brightness Down Previous Preset Motion Effect Tap or to select from the 10 preset motion effects: • Fading • Multicolor Ball • Color-Changing • Collision • Fireworks • Falling Rings • Tw
PAGE 4
FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 5
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. The device is compliance with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance.