Instruction Manual

Using the Optical Input
Insert one connector of an optical audio cable (not included) into the
optical audio input on the side of the speaker. Insert the other connector
into the optical output of your media-playing device.
The LED indicator will turn GREEN when the optical input is in use. While
connected, playback is controlled via the connected device. Volume can
be controlled with the speaker, remote control or the connected device.
Playing Music
To enjoy music on your speaker, make sure that the speaker is properly
paired to your Bluetooth-enabled device or connected via the 3.5 mm
auxiliary or optical audio input jack.
Controlling Playback & Volume (Bluetooth Only)
• Press the [ ] button to pause/resume media playback.
• Press the [ ] and [ ] buttons to skip tracks.
• Press and hold the [ ] and [ ] buttons to adjust volume.
Using the Remote Control
• [ ] Button: Enter/leave standby mode
• [ ] Button: Change input mode
• [ ] Button: Mute/unmute volume
• [ ] Button: Skip to previous track
• [ ] Button: Pause/resume playback
• [ ] Button: Skip to next track
• [ ] Button: Decrease volume
• [ ] Button: Reset to factory settings
• [ ] Button: Increase volume
Before You Begin... Getting Started
Caution
• READ THIS MANUAL AND SAVE FOR FUTURE REFERENCE
• THIS IS NOT A TOY, please keep away from children
• Do NOT submerge in water
• Keep away from extreme heat and/or humidity
• Do not open this product or attempt to repair the unit yourself should
it not be working.
• Low power may cause poor Bluetooth connection or sound distortion
• Only power this device with its suppiled power adapter
Questions & Customer Support
For any issues concerning this product, please visit our website at
SouthernTelecom.com and click on Product Support.
In the Box
• SBT2019 - Wireless Speaker (x1)
• 5V/1.5A Power Adapter (x1)
• RCA-3.5 mm AUX Cable (x1)
• Remote Control (x1)
• Instruction Manual (x1)
Location of Controls
Wall Mounting the Speaker
1. Remove the speaker and its contents from packaging.
2. Using a pencil, mark two spots on a wall measuring XXXXX inches apart.
3. If installing to a wooden surface, drive or drill a mounting screw into the
wall at each marked location. If installing to drywall or a brick surface, you
may need to install plastic anchors to properly secure the mounting
screws.
4. Place and hang the speaker from its mounting holes on the back onto
the installed mounting screws.
[ ] | [ ] Buttons
(Press +Hold) Skip Tracks
(Press) Adjust Volume
[ ] Button
(Press) Change input
mode (BT, AUX, Optical)
[ ] Button
(Press +Hold) Power
ON/OFF
(Press) Pause/resume
playback
DC Power
Input
3.5 mm Auxiliary
Audio Input
Optical Audio
Input
Powering ON/OFF
• Press and hold the [ ] button on the speaker to power ON. A tone will
be heard and the speaker will automatically enter Bluetooth pairing mode.
The speaker will automatically re-pair to any nearby, previously-paired
devices that have Bluetooth enabled.
• Press and hold the [ ] button again to power OFF.
Changing Input Modes
• Press the [ ] button to change between Bluetooth mode, 3.5 mm AUX,
and optical audio inputs.
Note: When plugging in a 3.5 mm or optical cable to the speaker, the
speaker will automatically switch to AUX mode.
Bluetooth Pairing
1. Power the speaker ON. A tone will be
heard and the LED indicator will quickly
ash BLUE.
2. Set your mobile device to search for
Bluetooth devices. When it appears,
select SBT2019 from the list of found
devices.
3. After a successful pairing, a tone will
be heard and the LED indicator will turn solid GREEN.
Using the 3.5 mm AUX Input
To use the speaker as a wired device, insert the 3.5 mm connector of the
supplied AUX cable into the 3.5 mm auxiliary audio input jack. Insert the
RCA connectors into the audio outputs of your media-playing device.
Note: Typically, RCA connectors are color-coded with Red being for the
right audio channel and white being for the left audio channel.
The LED indicator will turn GREEN when the AUX input is in use. While
connected, playback is controlled via the connected device. Volume can
be controlled with the speaker, remote control or the connected device.
Powering the Speaker
Insert the pin of the supplied 5V/1.5A power adapter into the DC power
input on the side of the speaker. Plug the adapter into an electrical outlet.
Speaker is ready
to pair