User's Manual

ManualsBrandsPoint Six ManualsElectronicsPart 15.231(e) Wireless voltage sensor

FCC ID: M5ZWOWANA

Installation and Operation Instructions for the Wireless Analog Sensor.

Point Six, Inc.

Wireless Analog Sensor Model WOWANA

Installation and Operation Instructions

The WOWANA wireless analog level sensor transmits a digital value representing either

0-20 MilliAmp, 0-5Volt or 0-10Volt levels and a unique serial number to a 418 MHz

receiver. The WOWANA is enclosed in a high impact ABS enclosure for direct surface

mounting in the environment to be measured. WOWANA is battery operated

Application: Apply the sensor to a surface to with double-sided adhesive tape. Make

sure that the side labeled with FCC ID is visible and away from any metal surfaces.

Service Function: The wireless analog sensor has an installation mode switch. A

momentary push of this switch will start the convert/transmit cycles. When new and until

this button is pushed the WOWANA will not transmit. The WOWANA will transmit a

special installation status mark in the data packet immediately after the installation/start

switch is pushed. After the start a push of the installation switch will result in the

immediate transmission of data and ID and installation status mark.

Battery: A 3.0-3.6 Volt lithium battery powers the WOWANA wireless sensor. The

battery will last for more than 10 years in the idle state (as shipped from the

manufacturer). The WOWANA will transmit data for as long as 3 years at a rate of once

each minute once started. The WOWANA is completely covered with a water resistant

rubber coating to protect the electronics from the environment and condensation. The

user cannot replace the battery. The WOWANA may be placed in a quiescent state

(battery life greater than 10 years) by holding the installation switch closed for more than

12 seconds.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES, OPERATION IS

SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY

NOT CAUSE HARMFUL INTERFERENCE A

ND (2) THIS DEVICE MUST ACCEPT

ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY

CAUSE UNDESERED OPERATION

FCC ID: M5ZWOWANA

MADE IN USA

Summary of content (4 pages)

PAGE 1
FCC ID: M5ZWOWANA Installation and Operation Instructions for the Wireless Analog Sensor. Point Six, Inc. Wireless Analog Sensor Model WOWANA Installation and Operation Instructions The WOWANA wireless analog level sensor transmits a digital value representing either 0-20 MilliAmp, 0-5Volt or 0-10Volt levels and a unique serial number to a 418 MHz receiver. The WOWANA is enclosed in a high impact ABS enclosure for direct surface mounting in the environment to be measured.
PAGE 2
FCC ID: M5ZWOWANA Wireless Analog Sensor Data Format The Point Six, Inc. 418 MHz wireless sensors require a compatible receiver with the ability to receive, error check and provide RS232 and RS422/485 interface. This document describes the data format provided by the HA8-wow 418 MHz. Receiver.
PAGE 3
FCC ID: M5ZWOWANA Example: C1283FA60B000000EC000F8AD0AB This field is the mode indicator, the LS-bit which indicates the service state of the transmitter, C1=normal, C0=service mode. C1283FA60B000000EC000F8AD0AB This field is the unique serial number of the 1-Wire sensor. C1283FA60B000000EC000F8AD0AB This is analog data field stored MSByte first as a 12-bit number in a 16-bit field. The number shown is 000F (15) or 15/4096 of full scale. If this is a 0-20 milliamp input this would be .
PAGE 4
FCC ID: M5ZWOWANA FCC Radio Frequency Interference Statement Wireless Analog Sensor FCC ID: M5ZWOWANA NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15, Subpart B, of the FCC Rules. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause interference to radio communications.