User's Manual

ManualsBrandsPoint Six ManualsElectronicsVibration Transmitter

FCC ID: M5ZVM1

Installation and Operation Instructions for the Wireless Vibration Sensor.

Point Six, Inc.

Wireless Vibration Sensor Model Point Sensor

Vibration

Installation and Operation Instructions

The Point Sensor Vibration wireless pressure sensor transmits a digital value representing

vibration, or other vibration levels from various range sensor elements and a unique serial

number to a 418 MHz receiver. The Point Sensor Vibration is enclosed in a high impact

ABS enclosure for direct surface mounting in the environment to be measured. Point

Sensor Vibration is battery operated, the battery may be replaced by the user.

Application: Apply the sensor to a surface to with double-sided adhesive tape. Make

sure that the side labeled with FCC ID is visible and away from any metal surfaces.

Service Function: The wireless vibration sensor has an installation mode switch. A

momentary push of this switch will start the convert/transmit cycles. When new and until

this button is pushed the Point Sensor Vibration will not transmit. The Point Sensor

Vibration will transmit a special installation status mark in the data packet immediately

after the installation/start switch is pushed. After the start a push of the installation

switch will result in the immediate transmission of data and ID and installation status

mark.

Battery: A 3.6 Volt lithium battery powers the Point Sensor Vibration wireless sensor.

The battery will last for more than 10 years in the idle state (as shipped from the

manufacturer). The Point Sensor Vibration will transmit data for as long as 3 years at a

rate of once each 30 seconds once started. The Point Sensor Vibration is completely

covered with a conformal coating to protect the electronics from the environment and

condensation. The Point Sensor Vibration may be placed in a quiescent state (battery life

greater than 10 years) by holding the installation switch closed for more than 5 seconds.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES, OPERATION IS

SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY

NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT

NY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY

CAUSE UNDESERED OPERATION

FCC ID: M5ZVM1

MADE IN USA

Summary of content (4 pages)

PAGE 1
FCC ID: M5ZVM1 Installation and Operation Instructions for the Wireless Vibration Sensor. Point Six, Inc. Wireless Vibration Sensor Model Point Sensor Vibration Installation and Operation Instructions The Point Sensor Vibration wireless pressure sensor transmits a digital value representing vibration, or other vibration levels from various range sensor elements and a unique serial number to a 418 MHz receiver.
PAGE 2
FCC ID: M5ZVM1 Wireless Vibration Sensor Data Format The Point Six, Inc. 418 MHz wireless sensors require a compatible receiver with the ability to receive, error check and provide RS232 and RS422/485 interface. This document describes the data format provided by the HA9-wow 418 MHz. Receiver.
PAGE 3
FCC ID: M5ZVM1 Example: 41283FA60B000000EC000F8AD0AB This field is the mode indicator, the LS-bit which indicates the service state of the transmitter, C1=normal, C0=service mode. 41283FA60B000000EC000F8AD0AB This field is the unique serial number of the 1-Wire sensor. 41283FA60B000000EC000F8AD0AB This is vibration data field stored MSByte first as a 12-bit number in a 16-bit field. The number shown is 000F (15) or 15/4096 of full scale.
PAGE 4
FCC ID: M5ZVM1 FCC Radio Frequency Interference Statement Wireless Vibration Sensor FCC ID: M5ZVM1 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15, Subpart B, of the FCC Rules. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause interference to radio communications.