User's Manual

ManualsBrandsPoint Six ManualsElectronicsWireless limit switch

FCC ID: M5ZLSX1

Installation and Operation Instructions for the Limit Switch Transmitter model LSX-1.

Point Six, Inc.

Wireless Engine Parameter Transmitter

Model WOW-LSX1

Installation and Operation Instructions

The WOW-LSX1 wireless limit switch transmitter transmits opened-closed status and

counter data with a unique serial number to a 418 MHz receiver. The LSX1 is enclosed

in a metal limit switch enclosure with a plastic dome lid. The LSX-1 is a Lithium battery

powered device that is mounted as a conventional limit switch on an automatic or manual

valve actuator. The status and opened/closed counter values are transmitted once each

minute.

Application: Attach the LSX-1 as a conventional limit switch package to the valve

actuator to be monitored. The LSX-1 is battery operated so no power connection is

required. Remove the lid by backing out the four corner screws. Press the pushbutton

located next to the limit switch package momentarily to start the adjustment LED

function. For a period of four minutes two LEDs on the PCB will indicate the status of

the opened/closed limit switches, this is provided as an adjustment aid for alignment of

the magnetic limit switch actuators. During this four-minute adjustment period the LEDs

will reflect the status of the limit switches. After this time period the LEDs will be turned

off and will not follow the status of the limit switches.

Battery: A 3.6 Volt lithium battery powers the WOWLSX1 wireless limit switch

transmitter. The battery will last for more than 10 years in the. The user can replace the

battery.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES, OPERATION IS

SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY

NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT

ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY

CAUSE UNDESERED OPERATION

FCC ID: M5ZLSX1

MADE IN USA

Summary of content (4 pages)

PAGE 1
FCC ID: M5ZLSX1 Installation and Operation Instructions for the Limit Switch Transmitter model LSX-1. Point Six, Inc. Wireless Engine Parameter Transmitter Model WOW-LSX1 Installation and Operation Instructions The WOW-LSX1 wireless limit switch transmitter transmits opened-closed status and counter data with a unique serial number to a 418 MHz receiver. The LSX1 is enclosed in a metal limit switch enclosure with a plastic dome lid.
PAGE 2
Wireless Temperature Sensor Data Format The Point Six, Inc. 418 MHz wireless transmitters require a compatible receiver with the ability to receive, error check and provide RS232 and RS422/485 interface. This document describes the data format provided by the HA8-WOW, HA9-WOW or HA10WOW 418 MHz. Receivers.
PAGE 3
Example: “ LSX” Wireless Limit Switch Transmitter 91F1D61300050000070000BD2DE1 11F1D61300050000070000BD2DE1 string from an HA8 string from an HA9 The device type field: LSX has device type 91/11 hex. A 90/10 hex when in service mode. 91F1D61300050000070000BD2DE1 11F1D61300050000070000BD2DE1 string from an HA8 string from an HA9 The MS-30 bits of these 4-bytes are the serial number of the LSX. The LS-2 bits are the status flags for the open and closed limit switches.
PAGE 4
91F1D61300050000070000BD2DE1 11F1D61300050000070000BD2DE1 string from an HA8 string from an HA9 This field is the mod 256 sum of all the ASCII character values in the response but does not include the . 91F1D61300050000070000BD2DE1 11F1D61300050000070000BD2DE1 string from an HA8 string from an HA9 This is the CR terminator, 0Dhex.