User's Manual

ManualsBrandsPoint Six ManualsElectronicsIR Door Transmitter

FCC ID: M5ZIR1

Installation and Operation Instructions for the Wireless IR Door .

Point Six, Inc.

Wireless IR Door Sensor Model Point Sensor IR Door

Installation and Operation Instructions

The Point Sensor IR Door wireless IR Door sensor transmits a digital value representing

either open or closed status, and the number of times the door has opened and closed and

has a unique serial number to a 418 MHz receiver. The Point Sensor IR Door is enclosed

in a high impact ABS enclosure for direct surface mounting in the environment to be

measured. Point Sensor IR Door is battery operated, the batteries may be replaced by the

user.

Application: Apply the sensor to a surface to with double-sided adhesive tape. Make

sure that the side labeled with FCC ID is visible and away from any metal surfaces.

Service Function: The wireless IR Door sensor has an installation mode switch. A

momentary push of this switch will start the convert/transmit cycles. When new and until

this button is pushed the Point Sensor IR Door will not transmit. The Point Sensor IR

Door will transmit a special installation status mark in the data packet immediately after

the installation/start switch is pushed. After the start a push of the installation switch will

result in the immediate transmission of data and ID and installation status mark.

Battery: Two 3.6 Volt lithium batteries power the Point Sensor IR Door wireless sensor.

Each battery will last for more than 10 years in the idle state (as shipped from the

manufacturer). The Point Sensor IR Door will transmit data for as long as 3 years at a

rate of once each 30 seconds once started. The Point Sensor IR Door is completely

covered with a water resistant conformal coating to protect the electronics from the

environment and condensation. The user cannot replace the battery. The Point Sensor IR

Door may be placed in a quiescent state (battery life greater than 10 years) by holding the

installation switch closed for more than 5 seconds.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES, OPERATION IS

SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY

NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT

NY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY

CAUSE UNDESERED OPERATION

FCC ID: M5ZIR1

MADE IN USA

Summary of content (4 pages)

PAGE 1
FCC ID: M5ZIR1 Installation and Operation Instructions for the Wireless IR Door . Point Six, Inc. Wireless IR Door Sensor Model Point Sensor IR Door Installation and Operation Instructions The Point Sensor IR Door wireless IR Door sensor transmits a digital value representing either open or closed status, and the number of times the door has opened and closed and has a unique serial number to a 418 MHz receiver.
PAGE 2
FCC ID: M5ZIR1 Wireless IR Door Sensor Data Format The Point Six, Inc. 418 MHz wireless sensors require a compatible receiver with the ability to receive, error check and provide RS232 and RS422/485 interface. This document describes the data format provided by the HA9-wow 418 MHz. Receiver.
PAGE 3
FCC ID: M5ZIR1 Example: “Point Sensor IR Door” Wireless IR Door Transmitter 91F1D61300050000070000BD2DE1 11F1D61300050000070000BD2DE1 string from an HA8 string from an HA9 The device type field: IR Door has device type 91/11 hex. A 90/10 hex when in service mode. 91F1D61300050000070000BD2DE1 11F1D61300050000070000BD2DE1 string from an HA8 string from an HA9 The MS-30 bits of these 4-bytes are the serial number of the IR Door. The LS-2 bits are the status flags for the open and closed.
PAGE 4
FCC ID: M5ZIR1 FCC Radio Frequency Interference Statement Wireless IR Door Sensor FCC ID: M5ZIR1 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15, Subpart B, of the FCC Rules. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause interference to radio communications.