User's Manual

ManualsBrandsPoint Six ManualsElectronicsWireless Analog Sensor

FCC ID: M5ZANA

Installation and Operation Instructions for the Point Sensor Analog transmitter.

Point Six, Inc.

Wireless Analog Sensor Model Point Sensor Analog

Installation and Operation Instructions

The Point Sensor Analog wireless analog level sensor transmits a digital value

representing either 0-20 MilliAmp, 0-5Volt or 0-10Volt levels and a unique serial

number to a 418 MHz receiver. The Point Sensor Analog is enclosed in a high impact

ABS enclosure for direct surface mounting in the environment to be measured. Point

Sensor Analog is battery operated

Application: Apply the sensor to a surface to with double-sided adhesive tape. Make

sure that the side labeled with FCC ID is visible and away from any metal surfaces.

Service Function: The wireless analog sensor has an installation mode switch. A

momentary push of this switch will start the convert/transmit cycles. When new and until

this button is pushed the Point Sensor Analog will not transmit. The Point Sensor

Analog will transmit a special installation status mark in the data packet immediately

after the installation/start switch is pushed. After the start a push of the installation

switch will result in the immediate transmission of data and ID and installation status

mark.

Battery: A 3.6 Volt lithium battery powers the Point Sensor Analog wireless sensor.

The battery will last for more than 10 years in the idle state (as shipped from the

manufacturer). The Point Sensor Analog will transmit data for as long as 10 years at a

rate of once each minute once started. The Point Sensor Analog is completely covered

with a water resistant conformal coating to protect the electronics from the environment

and condensation. The user may replace the battery. The Point Sensor Analog may be

placed in a quiescent state (battery life greater than 10 years) by holding the installation

switch closed for more than 4 seconds.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES, OPERATION IS

SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY

NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT

NY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY

CAUSE UNDESERED OPERATION

FCC ID: M5ZANA

MADE IN USA

Summary of content (4 pages)

PAGE 1
FCC ID: M5ZANA Installation and Operation Instructions for the Point Sensor Analog transmitter. Point Six, Inc. Wireless Analog Sensor Model Point Sensor Analog Installation and Operation Instructions The Point Sensor Analog wireless analog level sensor transmits a digital value representing either 0-20 MilliAmp, 0-5Volt or 0-10Volt levels and a unique serial number to a 418 MHz receiver.
PAGE 2
FCC ID: M5ZANA Point Sensor Analog Data Format The Point Six, Inc. 418 MHz wireless sensors require a compatible receiver with the ability to receive, error check and provide RS232 and RS422/485 interface. This document describes the data format provided by the HA8-wow 418 MHz. Receiver.
PAGE 3
FCC ID: M5ZANA Example: C1283FA60B000000EC000F8AD0AB This field is the mode indicator, the LS-bit which indicates the service state of the transmitter, C1=normal, C0=service mode. C1283FA60B000000EC000F8AD0AB This field is the unique serial number of the 1-Wire sensor. C1283FA60B000000EC000F8AD0AB This is analog data field stored MSByte first as a 12-bit number in a 16-bit field. The number shown is 000F (15) or 15/4096 of full scale. If this is a 0-20 milliamp input this would be .
PAGE 4
FCC ID: M5ZANA FCC Radio Frequency Interference Statement Point Sensor Analog FCC ID: M5ZANA NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15, Subpart B, of the FCC Rules. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause interference to radio communications.