Please note your phone is battery-embedded design with removable battery and battery cover. Unauthorized personnel are strictly prohibited from disassembling the phone. Make sure to use only the power adapter (5V 2A Output AC/DC) that came with PM90. In case your phone does not work as expected, you are strongly recommended to restart it by pressing and holding the power button for at least 12 seconds until the startup screen appears.
Table of Contents Table of Contents ................................................3 1 Accessary ............................................. 5 2 Setup PM90 .......................................... 6 2.1 Remove the Battery Cover ......................... 6 2.2 Insert the Battery .................................... 7 2.3 Close the Battery Cover............................. 7 2.4 Insert and Remove the SIM-SAM card ............ 8 2.5 Install and Remove the microSD card .............
1 Major Parts 1 Display, Touch panel 2 Receiver 10 9 Earphone cover 3 Front camera 11 Rear camera 4 Buttons 12 Speaker 5 Scan window 13 Battery cover 6 Volume button 14 Battery cover locker 7 Left scan button 15 USB port cover 8 Right scan button 16 Charging cradle connector 4 Power button
2 Accessary 5V 2.
3 Setup PM90 2.1 Remove the Battery Cover 1. Slide the Battery locker. 2. Lift up the Battery Cover. 3. Remove the Battery Cover.
2.2 Insert the Battery Insert “Battery” from top area. 2.3 Close the Battery Cover Insert “Battery Cover” from top area first and then put in bottom area. Press battery cover with both hand firmly.
2.4 Insert and Remove the SIM-SAM card You must insert your SIM card to make phone calls. Please power off your phone before inserting or removing the SIM card. 1. Remove the Battery Cover and the Battery. 2. Lift up the SIM rubber. 3. Insert the SIM-SAM card into the slot. (Gold plate should face down). Make sure that it is correctly inserted. 4. To remove the card, repeat step1 and step2, then remove the card out of the slot. Note: Your device only supports SIM cards.
2.5 Install and Remove the microSD card 1. Remove the Battery Cover and the Battery. 2. Lift up the SIM rubber. 3. Insert the microSD card into the slot (Gold plate should face down). 4. To remove the microSD card, repeat step1 and step2, then remove the card out of the slot. Note: To avoid data loss and SD card damage, please power off your phone before inserting or removing the SD card.
3 Charge PM90 1. Connect the AC/DC adaptor to your device and wall socket respectively. 2. LED indicator will display charging status. Steady Red Battery is charging or Battery level is low Blinking Red Battery level is critical low Steady Green Battery is fully charged PM90 Battery Specification Standard Battery 2,900mAh 3.85V Backup Battery 5,800mAh 3.85V Charging time About 5 hours Note: Always use an original charger and cable from the Point Mobile.
4 Turn On/Off PM90 Turn On 1. Press and hold down the “Power Key” for a few seconds. 2. When PM90 enter to the boot mode, it will display “SMART BEYOND RUGGED” logo with short vibration. 3. Release the “Power Key” and wait until PM90 finish booting. Note: If you cannot turn on your PM90, try below steps: - To turn on PM90, battery needs to be charged certain level. Please charge first. - Press and hold the “Power key” for 12 seconds to force reboot. Turn Off 1.
FCC warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
si lebrouillage est susceptible d’en compromettre le fonctionnement. This device is restricted to indoor use only within the 5.15 ~ 5.35GHz Band. Cet appareil est restreint a l'utilisation a l'interieur seulement dans la bande 5.15 ~ 5.35GHz. This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter unless authorized to do so by the FCC/IC.