Copyboard (Network board) User’s Manual Thank you for your purchase of the PLUS Copyboard. Please read this User’s Manual carefully before use to take full advantage of the functions of this product. After you have finished reading the manual, please keep it for future reference.
Introduction This manual is for the network board (model name: N-31S/N-31W/N-314). • The models are categorized into different types. Model Type N-31S Standard size for two screens N-31W Wide size for two screens N-314 Standard size for four screens The descriptions and diagrams in this manual refer to the model N-31S. For using a network, refer to “N-31 Series Network Manual”. * When functions or operations are specific to a certain model of network board, the model name is specified.
Table of Contents Introduction................................................................E-2 Package Contents.......................................................E-4 Names of the Parts.....................................................E-5 Front....................................................................... E-5 Input/output terminals.............................................. E-6 Changing the Height of the Unit................................ E-7 Control Panel.............................
Package Contents The package contents are as described below. Please check before use. Main unit [1] Pen tray [1] Printer* [1] Please see the instruction manual of the printer for information about the printer accessories. * Depending on the type of product you have purchased, the printer may be sold separately. Pen tray fixing screws (M4 × 20) (temporarily fastened on main unit) N-31S/N-314: 3 screws, N-31W: 4 screws (See the N-31 Series Assembly and Setup Manual for assembly instructions.
Names of the Parts Front Main unit Frame cover Sheet Dedicated markers are used on the sheet to draw diagrams and to write. Keypad panel (See Page E-9) Control panel (See Page E-8) Pen tray Input/output terminals (see next page) * Located on the bottom surface. Printer table The printer* is placed here. (See the N-31 Series Assembly and Setup Manual.) * The printer is sold separately. AC adapter box Store the AC power adapters of the network board and printer here.
Names of the Parts Input/output terminals USB memory port (type A) Connect a commercially available USB memory device. Scanned images can be saved. (See page E-20) The connector is located on the bottom surface of the main unit. The diagram view is seen from the bottom. * This illustration does not show the printer or connection cords. DC input connector Connect this with the DC plug end of the AC power adapter. (See Page E-35.) (Only connect the supplied AC power adapter; nothing else.
Names of the Parts Changing the Height of the Unit This is the height adjustment when setting up the network board on the optional stand. The stand height can be adjusted to 3 levels by 100 mm. CAUTION • At least two persons should hold the main unit. If not, the main unit could drop or tip, resulting in accidental injury. • Lock the stand’s casters by pressing the bottom of the caster lock button.
Names of the Parts 4 Control Panel Consecutive printing number indicators These light yellow to indicate the number of screens selected with the consecutive button. The control panel of the drawing refers to Model N-31S/N-31W. When pressing a button, please press the center area (the square bulge). The button may not work if it is pressed on a corner. 5 Thumbnail ( ) ( on N-314) button Used to select the layout for printing thumbnails of multiple screens on a single page.
Names of the Parts Keypad panel When pressing the button, press the center area (the square bulge). The button may not work if it is pressed on a corner. 1 2 3 4 5 1 IC card read/write part Touch the supplied IC card here. Reads or writes data to the IC card. Touch the touch mark with the IC card. Touching other places than the touch mark may cause an error. 2 Numeric (0 thru 9) button Enter the ID number for network storage. 3 Escape ( ) button Cancels entries on the keypad panel.
Functions of the Network board Printing Functions ① ② Printing Printing thumbnails of multiple screens on a single page Printing of thumbnails on single page Output to paper ③ Printing or storing multiple screens consecutively ④ Print to the network printer. LAN Consecutive printing or storing, one screen at a time FTP supported printer * Printing of thumbnails of 2 screens and consecutive on Model N-31S/N-31W.
Functions of the Network board Saving Functions ⑤ ⑥ Storing on USB memory devices Capturing images on a computer Storing on USB memory device Storing of image on computer ⑦ ⑧ Viewing images stored on the network board via a network Storing images on an FTP server via a network Network board’s memory Viewing of images stored on the network board ⑨ LAN LAN Viewing of images stored on FTP server Using the IC card to store images on a specific folder on an FTP server.
Operation Steps The network board uses an image scanner to scan characters or diagrams drawn using special markers (four colors). The image can be printed out to the printer and be stored on a USB memory device or a computer. When network settings are made with a network connected to the network board, the image can be saved on the network board or a FTP server, or can be printed out to the network printer on the network. To use a network, refer to the separate “N-31 Series Network Manual”.
Setting the Time The date and time are stamped on the printing paper and recorded in the file information when files are stored on the network board and FTP server, so set the network board’s time correctly. The time can also be set from a computer via a network (when connected to a LAN). In this section, operation for setting the time by using buttons on the network board is provided. Description of Operations 1 Switch to “CB Setup”.
Setting the Time While “F1” is displayed, press the Save to enter. button The display switches to “c1” (first 2 digits of year). If no buttons are operated for 10 seconds while in the time setting mode, the mode returns to the “CB Setup” mode. Press the Save its of the year button to move to the last dig- The display switches to “c2” (last 2 digits of year). Notice: The first two digits of the year (“20”) are fixed.
Printing (printer sold separately) Use a printer to print out the image that has been drawn on the sheet surface. Use a PLUS-designated printer. Operations and names of parts differ from printer to printer. For details of operations, see your printer’s operating instructions. The network board can print out to the printer connected to the network board or a network. Preparing the Printer Please check that the network board and the printer have been connected. See Page E-35. Set the paper.
Printing Basic Printing Operation Preparation: Preparation: Check that the AC power plugs of the network board and printer are connected to wall power outlets. Press the ON/Standby button and switch on the power. Prepare the printer. (See the previous page.) Note • When turning on the power, wait about 5 seconds or more after the power plug has been connected before pressing the ON/Standby button. • Press the ON/Standby button to switch on the power. The LED of the display window will light.
Printing Note • “01” is selected when the power is turned on. • Up to 10 copies can be specified and displayed on the display window. • The number of copies increases by 1 each time the Number of Copies button is pressed, and “ ” is displayed after “10” (this is used for test printing: see page E-32). When the button is pressed again, the display switches to “01”. The number switches continuously if the button is held in. • After setting the number of copies, proceed to step 4 within 1 minute.
Printing Moving the sheet surface manually The sheet can be moved even when the power of the network board is switched off. The sheet can be moved with your hand either in left or right. Please place your hand at the vertical center and move the sheet slowly. Notice • Quick movement can cause damage to the drive mechanism of the network board. Note • When the Erase Reminder function is set to “Enable”, the Erase Reminder function may not operate properly if the sheet surface is moved by hand.