BF-030PC BF-060 Control Software Setup Manual PLUS BOADWARE For Windows 95 Ver.2.
IMPORTANT 1. The copyright of this software belongs to PLUS CORPORATION and PLUS INDUSTRIAL CO.,LTD. 2. It is forbidden to use or copy a part or the whole of the software or manual without permission. 3. The software and manual may be used only in accordance with the terms of the agreement. 4. We do not accept any responsibility for effects resulting from use of the software or manual. 5. The specifications of the software and items described in the manual are subject to change without notice.
Contents 1 INTRODUCTION 6 1.1 Environment..............................................................................................................6 1.2 Notes..........................................................................................................................6 1.3 Terms and Symbols ................................................................................................7 2 HARDWARE SETUP 8 2.1 Setting Up the Copyboard BF-030PC ............................................
1 INTRODUCTION Welcome to PLUS BOARDWARE ! The SOFTWARE SETUP MANUAL (hereafter referred to as the manual) describes how to connect the PLUS Copyboard BF-030PC or BF-060, and how to set up and start the software. Please use it to ensure correct and efficient use of the software. For instructions on how to use the Copyboard, please refer to the Copyboard BF-030PC or BF-060 OPERATION MANUAL. 1.
1.3 Terms and Symbols The following terms and symbols are used in the manual and online Help.
2 HARDWARE SETUP 2.1 Setting Up the Copyboard BF-030PC (1) Make sure the power to the personal computer and Copyboard are switched off. (2) Use the interface cable provided and connect the connector at the bottom of the Copyboard to the serial port (DB9F (9 pins) COM 1 or COM 2 Port) on the appropriate type of personal computer. *1 A noise suppressing ferrite core (A) is provided at one end of the cable. Make sure that this end is connected to the Copyboard connector. (3) Switch the power on.
2.2 Setting Up the Copyboard BF-060 2.2.1 Package Contents The following items are enclosed in the package. In the event an item listed among the package contents is found to be missing or damaged immediately request a replacement from your retail store. ・PC interface board unit 1 pc. ・PC connection cable (D-sub 9 pin 2m) 1 pc.
2.2.2 Setup Setup the PC interface board according to the following procedure instructions. * Switch off all power to the main unit (electronic blackboard) and the PC before starting operations. * Touch some nearby metal (for example a door knob or aluminum sash) to discharge any static electricity built up on your body or clothes before starting operations. (1) Loosen the screws securing the cover over the expansion slot on the lower part of the unit, and remove this cover.
3 SOFTWARE SETUP 3.1 Setup Before Installing Please be sure you have read the software license agreement at the front of this manual before installing BOARDWARE. Installation Install BOARDWARE with the procedure below. (1) Start Windows 95 or NT and insert the BOARDWARE diskette into a disk drive. (2) From the [Start], select then choose . (3) Choose Programs. (4) Choose the [Install/Uninstall] tabs and then select the [Install] button.
4 OPERATION 4.1 Starting/Exiting Before starting PLUS BOARDWARE, check that the interface cable is connected, the power to the Copyboard is switched on and the lamp is on. If you have any problems, follow the setup procedure again. Note: When the power is switched on, the lamp lights up after about 4 sec and the Copyboard is on standby. The Copyboard cannot be operated until the lamp comes on. Check that the lamp is on before starting the program.
5 USER SUPPORT An inquiry service for questions relating to the software etc., and information about upgrading are only available to registered users. Fill in the necessary items on the enclosed Registration Card and return it to us as soon as possible. 5.1 Inquiries If there is something you do not understand about PLUS BOARDWARE, first consult the manual, HELP file and README contents.
6 CAUTION 6.1 Working Environment This product is a precision piece of equipment. The warranty does not cover breakdowns or trouble on the computer or breakdowns or trouble on the PC interface exp ansion board occurring due to incorrect handling. uCAUTIONS ON HANDLING q Be sure to eliminate all static electrical charges on the body or clothes before attempting installation of the PC interface. q Do not handle with moist hands or fingers. q Do not attempt unauthorized repairs or modifications.
PLUS CORPORATION 3-B22 NAKASE 1-CHOME, MIHAMA-KU, CHIBA 261-01 JAPAN PHONE: 043-296-3056 FAX: 043-296-3025 16 TELEX: J22113PLUSJIM, CABLE PLUSJIMUK TOKYO