MSDS

ManualsBrandsPlasti Dip ManualsPaint22 oz. Black Rubber Coating (6-Pack)

*Estimate

N/A-Not Applicable

N/R-Not Restricted

N/E-Not Established

MATERIAL SAFETY DATA SHEET

NOTE: BLANK SPACES ARE NOT PERMITTED. IF ANY ITEM IS NOT APPLICABLE, THE SPACE MUST BE MARKED TO INDICATE THAT.

IDENTITY

(As Shown On Label Or Package) F-907 22oz Plasti Dip

PART NO.

IF APPLICABLE

SECTION I

MANUFACTURER'S

NAME Plasti Dip International Inc.

EMERGENCY PHONE No.

USA only: 1-800-424-9300 INT’L: 703-527-3887

ADDRESS (NUMBER, STREET, CITY, STATE AND ZIP CODE)

3920 Pheasant Ridge Drive

REVISION #

Blaine, MN 55449

MANUFACTURER'S PHONE

No. FOR INFORMATION 1-763-785-2156

DATE MSDS

WAS PREPARED February 6, 2012

SECTION II - HAZARDOUS INGREDIENTS INFORMATION. All Health Hazards which comprise 1% or greater of the composition and all

carcinogens if 0.1% of the composition or greater.

HAZARDOUS COMPONENTS CHEMICAL

and IDENTITY AND COMMON NAME (S)

% Wt.

(OPTIONAL)

CAS NO. OSHA

PEL

ACGIH

TLV

OTHER LIMITS

RECOMMEND

VM&P Naphtha 36– 38 64742-89-8 300 ppm 300 ppm None

Heptane 18-20 426260-76-6 500 ppm 400 ppm None

Toluene 14 – 16 108-88-3 200 ppm 50 ppm None

Methyl Ethyl Ketone 3 – 5 78-93-3 200 ppm 200 ppm None

Resins N/A N/A N/A None

Carbon Black 133-86-4 3.5 mg/m

None

SECTION III - PHYSICAL / CHEMICAL CHARACTERISTICS

BOILING

POINT N/E

SPECIFIC GRAVITY (H

0 =1)

.79

APPROXIMATE WEIGHT PER GALLON (LBS)

6.62

VAPOR PRESSURE

125 mmHg @ 20°C

VAPOR DENSITY

(AIR = 1) Heavier than air

EVAPORATION RATE

(BUTYL ACETATE =1) >1.0

SOLUBILITY IN WATER

Insoluble

% VOLATILE 79.6

VOC LBS./GAL 5.27

OTHER

(IF ANY) None

APPEARANCE

AND ODOR Various colors, Honey Like Substance – Characteristic Odor

SECTION IV-FIRE AND EXPLOSION HAZARD DATA

FLASH POINT 15°F

(METHOD USED) TCC

FLAMMABLE LIMITS

LEL

0.9

UEL

11.5

EXTINGUISHING

MEDIA Carbon Dioxide, Dry Chemical, or Foam

SPECIAL FIRE

FIGHTING PROCEDURES Self contained breathing apparatus with a full face piece, operated in pressure demand or other positive pressure mode.

UNUSUAL FIRE AND

EXPLOSION HAZARDS This material is flammable and may be ignited by heat, sparks, flame or static electricity.

HAZARDOUS PRODUCTS FORMED BY

FIRE OR THERMAL DECOMPOSITION Carbon Dioxide and/or Carbon Monoxide

EXPLOSIVE LIMITS

(% BY VOLUME IN AIR) 0.9 – 11.5

SECTION V - OPTIONAL HAZARD RATINGS IDENTIFICATION

HAZARD RATING

4-EXTREME

3-HIGH

2-MODERATE

1-SLIGHT

0-INSIGNIFICANT

**SEE SECTION IV

National Fire Protection Association (NFPA)

FIRE 3 REACTIVITY 0 .

HEALTH 2 SPECIAL HAZARDS None .

This is the "front" when printed in duplex. Page 1 of 2 pages if not duplex.

Summary of content (2 pages)

PAGE 1
*Estimate N/A-Not Applicable N/R-Not Restricted N/E-Not Established MATERIAL SAFETY DATA SHEET NOTE: BLANK SPACES ARE NOT PERMITTED. IF ANY ITEM IS NOT APPLICABLE, THE SPACE MUST BE MARKED TO INDICATE THAT. IDENTITY PART NO. (As Shown On Label Or Package) F-907 22oz Plasti Dip IF APPLICABLE SECTION I MANUFACTURER'S EMERGENCY PHONE No. NAME Plasti Dip International Inc.
PAGE 2
SECTION VI - REACTIVITY AND STABILITY DATA STABILITY UNSTABLE STABLE X INCOMPATIBILITY (Materials to Avoid) Strong acids, bases, oxidizing agents, selected amines with alkali metals and halogens. HAZARDOUS DECOMPOSITION OR BY PRODUCTS Carbon Monoxide, Carbon Dioxide HAZARDOUS MAY OCCUR CONDITIONS TO AVOID May be ignited by heat, sparks, flame or static electricity.