Plantronics® Calisto™ Headset with Bluetooth® USB Adapter User Guide 56-K61A-15000
Table of Contents Package Contents........................................................................... 1 Product Features............................................................................. 2 Wearing Your Headset..................................................................... 3 Powering......................................................................................... 4 Charging.........................................................................................
Package Contents Calisto Headset Bluetooth Adapter USB Headset Charger 1
Product Features Reversible Earloop Call Control Button (on/off) Charge Connection Volume Adjust Noise-Canceling Microphone Pairing/Connect Button Indicator Light USB Connector 2
Wearing Your Headset Your headset can be worn on your left or right ear. To switch from one ear to the other, flip the ear loop to the side, and twist around.
Powering Your Headset and USB Bluetooth Adapter The headset automatically powers up when it is charging. Powering up: Press and hold Headset button for 2 seconds. 4 ascending beeps will sound when powered on. Powering down: Press and hold Headset button for 4 seconds. 4 descending beeps will sound when powered off. NOTE For your convenience, the headset comes pre-paired with the USB Bluetooth adapter, and (if the headset is within range) will automatically connect to the adapter when powered on.
Charging Your Headset Before using, you must first charge your headset. The indicator light glows solid red while charging and turns solid blue when the headset is fully charged. Charge the headset for a minimum of 2 hours. Battery talk time is up to 8 hours. NOTE Do not use headset while chargng and do not connect the charger while headset is in use.
Headset Indicator Lights and Alerts Headset Indicator Lights Action Button Action Sounds Indicator Lights Turn headset on Press and hold for 2 seconds 4 ascending beeps Flashes blue every 10 seconds Turn headset off Press and hold for 4 seconds 4 descending beeps Turn microphone on/off Press for 1 second 1 high beep Adjust volume Press up or down (not inward) 2 beeps when max/min volume reached Alert Sounds Indicator Lights Low battery 3 beeps every 30 seconds Flashes red 3 times every
USB Bluetooth Adapter Indicator Lights Action Indicator Lights Connected to the headset Solid blue Microphone on Flashes blue Disconnected from headset Flashes purple Pairing mode Flashes red and blue Pairing Your Headset with the USB Bluetooth Adapter NOTE The headset and USB Bluetooth adapter are paired to each other at the factory. However, if you have purchased a USB Bluetooth adapter separately, or if you wish to use a replacement headset with your existing adapter, the units must be paired.
4. To put the USB Bluetooth adapter into pairing mode, Pinch the pairing/ connect button for at least 2 seconds until adapter flashes red and blue and begin pairing with your Bluetooth headset. 5. When both USB adapter and headset are in pairing mode, and within 30 feet of each other, they should connect. 6. The USB adapter show a solid blue light when connected to the headset. NOTE Take caution when manually pairing the USB adapter. Do not press hard.
4. If Dragon prompts you to “Choose the device you will use for speech recognition”, select Plantronics BT Adapter from the list and then click Next to continue. 5. If Dragon tells you that your “Sound level is too low”, the headset microphone may be turned off. Make sure that it is turned on and try reading the text again. NOTE If after following the above steps, you still receive the “Sound level is too low” message from Dragon, your Windows sound system may not be setup correctly. Visit http://support.
Using the Headset with MacSpeech Dictate When creating a new user profile within MacSpeech Dictate for your headset, note the following: 1. If you have not activated Enable Access for Assistive Devices in Universal Access section of your System Preferences, you will be prompted to do so before you can continue. 2. Next, you will need to create a user profile so that MacSpeech Dictate can get used to your voice, your microphone, and your speech. You will see a blank Profiles Window. 3.
Regulatory Notices FCC Requirements Part 15 This device complies with part 15 of the FCC Rules subpart B. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
© 2008 Plantronics, Inc. All rights reserved. Plantronics, the logo design, Calisto, and Sound Innovation are trademarks or registered trademarks of Plantronics, Inc. The Bluetooth® word mark is owned by Bluetooth SIG,Inc., and any use of the mark by Plantronics, Inc. is under license 56-K61A-15000 (12.