User's Manual

ManualsBrandsPlanet Technology ManualsElectronics802.11 a/n Wireless Outdoor CPE

Note

– 1 – – 2 –

– 3 – – 4 –

1. Package Contents

2. Installation Precautions

3. Physical Introduction

– 7 – – 8 –

– 5 – – 6 –

The above steps introduce the simple installations and

configurations of the WNAP-7325. For further configurations of

different operation modes, please refer to the user manual which

you can download from the website.

http://www.planet.com.tw/en/support/download.php?type1=4&

model=48590&type=3

If you have further questions, please contact the local dealer or

distributor where you purchased this product.

2011-E10580-000

Thank you for choosing PLANET WNAP-7325. Before installing the

AP, please verify the contents inside the package box.

If there is any item missing or damaged, please

contact the seller immediately.

Connect the WNAP-7325 with your PC by an Ethernet cable

plugging in LAN port of PoE injector in one side and in LAN port of

PC in the other side. Power on the WNAP-7325 by PoE from PoE

injector.

1. Click “Start” button located in the lower-left corner of your

computer.

2. Click “Control Panel”.

3. Double-click “Network and Sharing Center” icon.

4. Click “Change Adapter Settings”.

5. Double-click “Local Area Connection”.

6. Select “Internet Protocol Version 4 (TCP/IPv4)” and

click “Properties”.

7. Select “Use the following IP address”, and then click

“OK” button twice to save the configuration. For example,

as the default IP address of the WNAP-7325 is

192.168.1.253 and the router is 192.168.1.254, then you

may choose from 192.168.1.1 to 192.168.1.252.

Default IP Address: 192.168.1.253

Default Username: admin

Default Password: admin

Default SSID: WNAP-7325

STEP 1: The Web management allows you to access and

manage the wireless AP easily. Launch the Web

browser and enter the default IP address

http://192.168.1.253.

WNAP-7325

Quick Installation Guide

300Mbps 802.11a/n Wireless Outdoor CPE

For security reasons, it is recommended to change the

password at the first login and memorize it.

STEP 2: When the login window pops up, please enter the

User Name and Password. The default User Name

and Password are both “admin”. Then click OK

button to continue.

STEP 3: After you enter into the Web User Interface, go to

Operation Mode to configure your wireless network.

Rear Panel Description – LED Indication

Plastic Strap x 1

Quick Guide

PoE Injector & Power Cord

Signal IndicatorLAN 2 LED

Power LED LAN 1 LED

STEP 1: Place the strap through the slot on the back of the

WNAP-7325 and then around the pole. Tighten the

strap to secure the WNAP-7325.

5. Pole Mounting

Further Information:

6. Web Login

IMPORTANT SAFETY PRECAUTIONS:

1) LIVES MAY BE AT RISK! Please be aware for

the electric wires around, and tighten the

pole. Carefully read the section "OUTDOOR

INSTALLATION WARNING" in the manual

before installation.

2) Users MUST use the “Power cord and PoE

Injector” shipped in the box with the

WNAP-7325. Otherwise, the product might be

damaged.

Caution

WNAP-7325

STEP 2: Plug the power cord into the DC port and the other

side into the AC socket. Then, plug the RJ45 cable

(as shown in picture 4 under Step 1) into the POE

port of the PoE injector.

STEP 1: (A) Push the latch on the bottom of the WNAP-7325

to remove the sliding cover.

Bottom Panel Description – Port

4. Hardware Installation

1 2

3 4

Grounding Terminal

Reset Button

LAN2 PoE LAN

(B) Plug the RJ45 Ethernet cable into the PoE LAN Port of the

WNAP-7325. Then, slide back the cover of the WNAP-7325

to finish the installation.

Ethernet Cable

PoE Port

Ethernet Cable

24V PoE Injector

Data+Power

Power

Data

LAN POE

PoE Out

Data In

1. Users MUST use a proper and well-installed

surge arrestor and grounding wired with the

WNAP-7325; otherwise, a sudden lightning

could cause fatal damage to the WNAP-7325.

EMD (Lightning) DAMAGE IS NOT COVERED

UNDER WARRANTY.

2. Users MUST use the “Power cord and PoE

Injector” shipped in the box with the

WNAP-7325. Use of other options will cause

damage to the WNAP-7325.

Caution

Summary of content (3 pages)

PAGE 1
2. Installation Precautions Quick Installation Guide 1. Users MUST use a proper and well-installed surge arrestor and grounding wired with the WNAP-7325; otherwise, a sudden lightning could cause fatal damage to the WNAP-7325. EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY. WNAP-7325 300Mbps 802.11a/n Wireless Outdoor CPE Caution 1. Package Contents Thank you for choosing PLANET WNAP-7325. Before installing the AP, please verify the contents inside the package box. WNAP-7325 2.
PAGE 2
5. Pole Mounting 6. Web Login STEP 1: Place the strap through the slot on the back of the WNAP-7325 and then around the pole. Tighten the strap to secure the WNAP-7325. Connect the WNAP-7325 with your PC by an Ethernet cable plugging in LAN port of PoE injector in one side and in LAN port of PC in the other side. Power on the WNAP-7325 by PoE from PoE injector. 1. Click “Start” button located in the lower-left corner of your computer. 2. Click “Control Panel”. 3.
PAGE 3
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.