TABLE OF CONTENTS BE F 0 R E Y 0 U START----------------------------------------------------------------- 2 IMPORTANT SAFETY PRECAUTIONS INSTALLATION PRECAUTIONS ~IRE: DIA(;RARn ------------------------------------------------------------------------3 S P E: A K E: R M 0 U NT I N c; S U c; c; EST I 0 N S --------------------------------------- 3 BE: F 0 R E I N STALL I N c; T H IS P R 0 [) U C T -------------------------------------·· 4 TECHNICAL SUPPORT S U c; c; EST E: D M 0 U NT I N c; M ET H 0 DS ---
BEFORE YOU START • BE SURE TO OBSERVE THE FOLLOWING GUIDELINES: - Do not turn up the volume so high that you can't hear what's around you. - Use caution or temporarily discontinue use in potentially hazardous situations. • Do not operate mobile video equipment while driving a motorized vehicle- safe driving and safety consideration of others should always be your highest priority.
WIRE DIAGRAM I QUICK RELEASE POWER ADAPTOR (INCLUDED) Align arrows Replace with 15A AGC Fuse type only OPTIONAL DIRECT BATTERY WIRING CIRCUIT : ; 'IJ : : • ; : "':"' i~o1AI 0 U Recommended 12- 14ga Wire DO~ I BATTERY Fuse and fuse holder (not Included) RED Normally open switch Ground wi1'11 (not Included) ® \ Chassis ground ~ ~ ~ ~~ ' ' 0 ' BLACK l Chassls ground point ~~~- Metal frame SPEAKER MOUNTING SUGGESTIO NS Route strap around the speaker body to vehicle frame Route
BEFORE INSTALLING THIS PRODUCT To avoid potential shorts in the electrical system, be sure to disconnect the (-) battery cable before installation. Use this unit with a 12-volt battery and negative grounding only. Failure to do so may result in a fire or malfunction. A ~ A RISKOFELECTRICSHOCK DONOT
SUGGESTED MOUNTING METHODS The PATV65 can be mounted in two different configurations: I G) SURFACE MOUNT To surface mount use double sided tape or velcro. (not included) ®HANDLEBAR MOUNT Use the provided handelbar clamp kit, try the best method for your application, securely tighten all components.
GETTING STARTED @® CD ® ® 0 ® 0 0 ® ® ® ® MFC- MULTIFUNCTION CONTROLLER VOLUME DOWN VOLUMEUP LED DRIVING LAMP - ON/OFF PLAY/PAUSE NEXTTRACK PREVIOUS TRACK SYSTEM POWER -ON/OFF POWER I SOURCE - RED =AUX-IN MODE I BLUE = BT MODE BLUETOOTH PAIRING INDICATOR - BLUE COLOR @ 3.
BLUETOOTH OPERATION * I ·ll)) PAIRING & DISCOVERING A NEW BLUETOOTH CONNECTION 1) Power on the PATV65 by pressing and holding down the (j) Power button for 3 seconds, the ®BLUE and @RED LEOs will start to alternately flash, signalling that the PATV65 is now ready for Bluetooth pairing. NOTE: You have 2 minutes before you must restart this procedure over again . 2) Now that the PATV65 is in pairing mode: ANDROID users: a. Go into the Settings Menu of your device b.
.... BLUETOOTH OPERATION / RECONNECTION 1) Power on the PATV65 and your last paired device Bluetooth. 2) The unit will now automatically reconnect, the BLUE LED will be ON. 3) If your device was previously paired with the PATV65, but it wasn't the last paired device: a. b. c. d.
STREAMING MUSIC I ' @® * 'Ill)) ((( [EJ 0 ® .
AUX-INPUT YOUR DEVICE ® YOUR CABLE AUX-IN OPERATION PATV65 can play audio from any device that has a 3.5mm hea~one audio jack. 1) Power on the PATV65 by pressing and holding down the POWER ~button for 2 seconds 2) Connect the 3.5mm AUX-IN on the MFU to a 3.5mm adaptor@ (3.
INFORMATION TO THE USER I FCC COMPLIANCE STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. The Bluetooth antenna cannot be removed (or replaced) by user.
TROUBLE SHOOTING GUIDE CAUSE TROUBLE SOLUTION The fuse is blown Check I replace the fuse Bad accessory power connection Check accessory power port for proper operational voltage Blown speaker Replace faulty speaker Volume is low I muted Press the volume level up Device is paused or muted Check your devices playing I volume status The Bluetooth function of the device is not enabled Refer to the user manual of the device for how to enable the Bluetooth function The PATV65 memory is full Turn o
All trademarks and trade names are those of their respective owners.
PLACE POSTAGE HERE
ONE YEAR LIMITED WARRAN TY This product has a manufacturer's warranty against defects in materials and workmanship to the original purchaser for a period of one year from the date-of-purchase [DOP]. This manufacturer warranty is non-transferable. The warranty is for repair or replacement at the sole discretion of PLANET AUDIO [PA]. For service under this warranty you need to return the product to PA.