€ Punctual Audio AC1000.2 Iwo Champ! AC1200.2 Amati AC2000.2 AC2600.2 AC1600.4 Four Camel AC2400.4 ‘motes AC1800.5 Jno AC1500AM Topmost AC2500.1M Steamfitters Congratulations on your purchase of a Planet Audio ANARCHY Amplifier. It has been designed, engineered and manufactured to bring you the highest level of performance and quality, and will afford you years of listening pleasure.
Introduction With the Planet Audio ANARCHY SAMOSET amplifier series, we are introducing eleven new amplifiers, all designed in the USA. This new series includes a two mono blocks, four channel amps, two 4-channel amps and one 5-channel amplifier . The 2CH, 4CH and 5CH ANARCHY models feature variable low pass and high pass crossovers (The mono blocks have low pass crossovers). All amps feature variable Input gain controls.
Features Your new ANARCHY amplifier features the following: « Class A-B operation + Bridgeable outputs (except AC1500.1M and AC2500.1M) « Ti-Mode capable (except AC1500.1M and AC2500.
General precautions Before Installing and using your new Planet Audio amplifier, please become familiar with ail the Information contained in this manual. Please keep this manual in a safe place for future reference. + Do not open or attempt to repair this unit yourself. Dangerous high voltages are present which may result In electric shock. Refer any repairs to a qualified service technician.
Connecting the amplifier Before doing any wiring, look through this manual and identify the diagrams to follow for power, input and speaker connections for your particular installation. Be sure you understand all the connections before you proceed. 1. Connect the power ground terminal to the closest point on the chassis of the car. Keep this ground wire to less than 38" (100 cm) In length. Use 8 gauge (or heavier} wire. 2.
Low Level Input Wiring Low-level (RCA) input wiring is preferred for best audio performance. Always use a high-quality RCA cable for best audio performance. NOTE: Do nol connect BOTH tha high level and iow lave! inputs from your receiver to your amplifier at the same time! Remote Sub woofer 2-Channel Amplifiers Level SE AC1000.2, AC1200.2, AG2000.2 and AG2600.2 — =e] © Soto 4-Channel Amplifiers AC1600.4 and AC2400.
Low Level Input Wiring Low-level (RCA) input wiring is preferred for best audio performance. Always use a high-quality RCA cable for best audio performance. NOTE: Do nol connect BOTH tha high level and iow lave! inputs from your receiver to your amplifier at the same time! 5-Channel Amplifier AC1800.5 © Mono Block Amplifiers AC1500.1M and AC2500.
High Level Input Wiring The high level input(s) should only bs used when your head unit lacks RCA outputs. If the RCA outputs are not present, connect the speaker outputs from the receiver to the high level input connector of the amplifier. Be sure to observe polarity to avoid audio phase problems. NOTE: Do pot connect BOTH the high feel and low level inputs from your receiver to your amplifier at the same time! 2-Channel Amplifiers AG1000.2, AG1200.2, AG2000.2 and AC2600.
High Level Input Wiring The high level Input{s) should only ba used when your head unit lacks RCA outputs. If the RCA outputs are not present, connect the speaker outputs from the receiver to the high level input connector of the amplifier. Be sure to observe polarity to avoid audio phase problems. NOTE: Do not connect BOTH the high level and low feel inputs from your receiver fo your amplifier at the same mel 5-Channel Amplifier AC1800.
Power and Speaker Wiring 2-Channel Amplifiers % Meghan sud Bridged Biden er Speaker Rich T BEAKER —( Speaker IMPEDANCE J 280HMS Mode Tg 1 1 Chassis — ground point XJ EIT LY } = Connect the Positive terminal of tha = ground sub woofer to the L f+) amplifier terminal.
Power and Speaker Wiring 2-Channel Amplifiers Hb Bede AC1000.2, AC1200.2, AG2000.2 and AC2600.2 TH-mode operation allows you to connect this amplifier to a pale of main speakers plus a sub woofer on one pale of output channels. The main speakers will operate In STEREO while the sub woofer simultaneously operates in MONO. To set up the amplifier to run in this mods, put the crossover switches in the FULL position.
Power and Speaker Wiring 4-Channel Amplifiers # Ham sud Bridged Biden AG1600.4 and AG2400.4 SDE 22) IMPEDANCE Speaker 28 OHMS Four Channel Mode © ok = (poo peeing “ome owe EEE ppl] A 5 So==] Era? Pda] Pine] voi = — Chassis. SPEAKER =p = ond IMPEDANCE Spear] 28 on Mg \— to REMOTE TURN-ON == rm this 2 a FUSE [oem ] Connect the Negative terminal of the RIGHT sub woofer to the CH2 amplifier terminal. RIGHT Subtract Connect the Positive terminal of the RIGHT sub woofer to the CHT amplifier terminal.
Power and Speaker Wiring 4-Channel Amplifiers FoR AG1600.4 and AG2400.4 Ti-mode operation allows you to connect this amplifier to a pair of main speakers plus a suborder on one pair of output channels. The main speakers will operate in STEREO while the sub woofer simultaneously operates in AMONG. To set up the amplifier to run in this mode, put the crossover switches in the FULL postilion. Insert high pass fleeter capacitors and a low pass filter Induct or Into the wining as shown below.
Power and Speaker Wiring S-Channel Amplifier ol Isle AG1800.5 Ti-mode operation allows you to connect this amplifier to a pair of main speakers plus a suborder on one pair of output channels. The main speakers will operate in STEREO while the sub woofer simultaneously operates in AMONG. To set up the amplifier to run in this mode, put the crossover switches in the FULL postilion. Insert high pass fleeter capacitors and a low pass filter Induct or Into the wining as shown below.
Power and Speaker Wiring Mono Block Amplifiers Homelike Bade AG1500.1M and AC2500.1M Pier SPEAKER IMPEDANCE Mono Block 2.6 OHMS Mode FEE Planet Audio Chassis.
Troubleshooting If you experience operation or performance problems with this product, compare your installation with the electrical wiring diagram on the previous pages. If problems persist, read the following troubleshooting tips which may help eliminate the problems. SYMPTOM POSSIBLE REMEDY Amplifier will not | Check to make sure you have a good ground connection. power up. Check that the Remote input (Turn-On} has at least 3VDC. Check that thees is battery power on the terminal.