Wireless Timer Remote Control 无线定时快门线 TW-282 50202 V10.
Contents Overview Cautions TW-282 introduction The name of each part Prepare for install and use Install and replace the battery Fix the receiver(TW-282RX) Turned on/off the power Channel Setting Open the background light of display Receiver connected with the camera Shooting control Single shooting Continuous shooting within one sec 03 04 07 08 11 11 13 14 15 17 18 19 19 20 1
Overview Thank you for purchasing high-performance PIXEL products [ ]shooting Delay shooting Timing plan for shooting 22 23 26 First of all, thank you for purchasing product of PIXEL TW-282. The shooting ways included single shooting, continuous shooting within one sec, [ ] shooting, user-defined time-delay and timing plan for shooting. Low consumption of LCD display will make you be clear at a glance of the using status and using plan.
The name of each part Please check all included items after contact the dealer. 1. Transmitter (TW-282TX) ------- 1pc 3. 1.5V AAA battery ---------------- 2pcs 5. Shutter connect cable ---------- 1pc The name of each part open the packing, if missing, please 2. Receiver (TW-282RX) ---------- 1pc 4. CR-2 Lithium battery ------------ 1pc 6.
Preparation for installation and use The name of each part Display of transmitter 9 10 11 12 13 DC0 DC1 DC2 E3 N3 S1 RS1 UC1 CB1 1 Install and replace the battery 1 2 The transmitter(TW-282TX) 2 3 4 5 6 7 8 Shutter connect cable 1 Input plug 2 Shutter connect plug Display of transmitter 1 3 5 7 9 11 13 10 Before use, you should read the user manual of your camera carefully and well understand the manipulation and functional setting.
Preparation for installation and use 2. Follow the signs of positive [+] and negative [-] in the battery compartment to install the battery correctly. You should pay attention to the polarity of battery because of the wrong installation will make the device work abnormally, or even physical injury. 3. Close the battery hatch.
Preparation for installation and use Turned on/off the power The transmitter(TW-282TX) 1. Press any button once, and turn on the power of transmitter. 2. Turn on the power, transmitter in single shooting state, set the timing plan and communication channel unchanged. 3. The display shows the single shooting icon and communication channel. 4. The transmitter without any operation (except timing plan or implementing [ ] status) will shut down automatically after one minute. The receiver(TW-282RX) 2s 14 1.
Preparation for installation and use Preparation for installation and use Open the background light of display Channel model 1. When the transmitter's communication channel adjust to [ -- ] will effectively control all channels within the region of the receiver . 2. When the receiver's communication channel adjust to [ -- ] , all transmitter in the effective reception area can control the receiver. 3. The transmitter and receiver’s value of communication channels setting must be consistent .
Preparation for installation and use Receiver connected with the camera 1. Make sure your receiver has been installed in place and to ensure that cameras and receivers are shut down. 2. First, insert the input plug of the shutter connect cable into the receiver' s output control signal socket in place. FS Wir ele o K 2 ntroll .4G er Hz ss C The timer remote control will not be able to control the camera if the shutter connect cable didn’t insert correctly. 3.
Shooting control 3. Full-press the release button and transmitter will send signal of shooting. The red indicator will light for a while, the camera start shooting. Make sure to set the camera function to be [ ]. When the camera function is set to be[ ], it may cause continuous shooting. When the camera function is set to be[ ],the camera will shoot based on[ ]mode, it may cause underexposure or overexposure. When the camera function is set to be [ ], the camera will execute delay shooting.
Shooting control [ ]shooting 1. In the power-on state, move the transmitter's activities icon to [ ] shooting icon[ ] by pressing the left move button[ ]or right move button[ ]. 2. Half-press the release button and transmitter will send signal for focusing, the green indicator will lit on the transmitter and receiver, and the camera is in the focusing state until the release or full-press the button. 3. Full-press the release button, transmitter will send[ ] signal.
Shooting control Shooting control press button [ ], settings shot number can be reduced. It can be set between 1 to 99 sheets . 3. Press button[ ]enter into the delay setting of delay shooting. the delay shooting icon[ ] , delay shooting time icon[ ], delay shooting time value[ ]will blink at the same time. 4. Press the button[ ], set the delay time increased, press button[ ], set the delay time reduced. It can be set between 1 to 59 seconds. 5.
Shooting control Shooting control When the camera lens focus function is set to be [ A ], even receiving the shooting signal the camera will not shoot at the moment as most of camera don't seize focus. Timing plan for shooting 4. Press the set button, save and exit settings. Exposure time setting Delay time setting 1. In the power-on state, move the functional activities icon to the delay timing program icon[ ]by pressing the left move button[ ]or right move button[ ]. 2.
Shooting control Shooting control Gently press button[ ]once to set numerical increased, hold it on, set the value rapidly increased; Press the button[ ]once to set the numerical reduced, hold on to set the values rapidly reduced. 4. Press the set button, save and exit settings. 4. Press the set button, save and exit settings. Interval time setting The shot number setting 1. Press left move button[ ]or right move button[ ], move the transmitter’s activities icon to the interval timing program icon[ ].
Shooting control Shooting control Interval time of timing plan setting Press Press Press Press 2. Press the timing start/stop button[ ], the transmitter will sent all information to the receiver. The timing plan will run in the receiver, and output control signals to camera. Delay time of timing plan setting Press the timing plan start/stop button[ ]of the transmitter before the timing plan executing completely, the transmitter and receiver will stop regularly scheduled executing.
PIXEL TW-282 Specification Type : FSK 2.4 GHz wireless control system Transmission distance: 80 meters or above Channel: 99 channels, as well as ALL Standby time: Transmitter : more than 4 years(using two 1.5V AAA batteries) Receiver : 400 hours (using CR-2 lithium battery) Dimensions (W ×H ×D) : Transmitter: 149mm×49.5mm×24mm Weight ( with ba ttery): 63mm×38mm×31mm Receiver: Transmitte: 70.5 g 39.5 g Receiver: Now you can start to use unique high-performance PIXEL product TW-282.