User's Manual

ManualsBrandsPixel ManualsElectronicsWireless flash trigger

Thank you so much for purchasing PIXEL product, ROOK is a professional

grouping flash trigger. TTL mode available on transmitter hot shoe and sync with off

shoe trigger together. Off shoe trigger can be grouped the flash and Remote the

camera. ROOK is using global free FSK 2.4GHz which is more stabilize.

1、Make sure the camera is powered off before install device.

2、This is electronic products accessories; some of the environment causes may

affect

the working. However this is hardly ever to get this situation, don't worry!

3、

This component can't be strong vibration, or may lead to product failure.

4、For a long time non-use, please turned off the transmitter and the receiver's

power and remove the battery.

5、The batteries should not install anti-polarity; otherwise the batteries may leak.

corrosive liquids, heat or explosion.

6、When the product connected to the device, Do not pull the wires.

7、Do not put it in high temperature, such as a closed car under direct sunlight, the

control panel

and other high-temperature areas.

8、

keep dry, do not use wet hand contact with the product, the product must not be

immersed in water or exposed to rain, and this may lead to not work properly.

9、Do not use flammable gases in violation of this warning may cause an explosion

or fire.

、10 Because of this product is included battery; please strictly follow the instruction

for operation. Otherwise its may cause an explosion, fire or personal injury.

Overview

1 ROOK is a professional grouping flash trigger.

2 Transmitter hot shoe support TTL and sync with off shoe flash.

3 Wake-up function available, the flash will be wake up automatically.

4 Through studio light to connect PC or USB socket, the sync speed up to 1/320s

(Sync time may have little bit inacurracy as difference camera model )

5 Available to control the shooting or through master camera to control

slave camera.

、

Receiver

Professional Flash Trigger

Instruction Manual

ROOK

Power/group

switch

Chanel setting

Indicator

Light

Battery

compartment

Output socket

l F

h Tr

Sony series camera, Minolta series camera

ROOK Model compatible list as below：

Transmitter(TX)

Receiver(RX)

Canon series camera

Nikon se ries camera, Samsung seri es camera

Fujifi lm series camera, Pa ntex series camera

Compatible

Trigger point

Group Indicate

Light

Chanel setting

Power/group setting

Battery

compartment

1 2

76 8

Input/output

socket

Transmitter

Hot shoe protector

Included Items

Specification

Battery Installation:

Set transmitter and receiver to the same channel

AAA

Please locate the battery according

to the icon in the battery compartment.

Channel Setting:

Set transmitter and receiver to the

same channel

1.Slide the switch to change channel.

Channel changing as:

CH1→ CH2→ CH3→CH4 (as figure)

For a long time non-use, please turned off the transmitter and the receiver's

power and remove the battery.

* Transmitter and receiver must be set as the same channel.

* A、B、C LED light on means the current setting will be working with

transmitter.

4. No action within 2 seconds, the group LED light will off.

*Receiver only get signal from transmitter when the current group

setting of receiver is included in the validate group of transmitter.

Testing:

1. Check power on or off.

2. Check the frequency of transmitter and receiver.

3. Check the group setting of transmitter and receiver.

Group setting:

Group setting on transmitter

1.wake up group display, and show the current controlling group. Slightly press

[ ] to show group mode which showing the current working group.

2. Press again [ ] to change group.

3. Group changin

g a s :

Group setting on receiver

Put Power/group switch at A/B/C,

and then turn on the receivers.

3.Trigger the Flash.

1.Insert flashgun on the receiver and turn on the flash power; set the flash

index as minimum.

2.Full press the test button

1. Tight the Hot shoe with screw, and then turn right to

release.

2. Plug the transmitter on the camera hot shoe.

3. Tight the Hot shoe with screw, and then turn

left to lock.

Connect the transmitter to camera hot shoe

1. Plug PC-3.5 connecting cable to transmitter 3.5mm socket.

2. Plug PC-3.5 connecting cable to camera PC socket.

Connect transmitter to camera via PC-3.5 connecting cable.

How to connect the relative photo equipment

Testing the receiver signal as below:

(2(1

1. Split the protecting film on the receiver holder and stick it on

the studio light as figure.

2. Mount the receiver on the receiver holder.

3. Use 3.5-3.5 or 3.5-1/2 according to studio light socket.

4. Plug 3.5mm side into the transmitter input.

5.Insert another side into the studio light socket.

Connect the Receiver to Studio Light

1. Unlock the Speedlite Flash locking screw.

2. Insert the Speedlite Flash into the receiver hot shoe

as figure.

3. According to the flash locking method to lock the

speedlite on receiver.

Connect the Receiver to Speedlite Flash

1.Plug shutter connecting

cable (3.5mm side) into the

receiver socket.

2.Plug shutter connecting

cable (camera side) into

the camera shutter release

socket.

Connect Receiver to Camera

(1 (2

Cautions before use

Receiver holder

for Canon

for Nikon

for Sony

for Olympus/

Panasonic

For Sony

for Olympus/

Panasonic

For Nikon

For Canon

Model

Above brand name is registered by the respective owner.

Qriginal speedlite,

studio light,Metz,

SUNPAK,Sigma

Olympus/Panasonic series camera

Feature

Prepare to use

*PC-3.5 connecting cable should be purchased separately.

（）Trans m itter

Trans m itter Receiver Trans m itter Receiver

*The shutter cable should be purchased separately.

Wireless Frequency System:

Operating Distance:

Shutter Sync Speed:

1/200S

Group setting: 3 difference group (7 combinations)

Wireless Channel: 4

Stand-by Time 250 hours

： :

Transmitter: 5years

Power:

AAA x2

Weight: Transmitter 48.5g (without batter y)

Receiver 44.0g (without battery)

FSK2.4GHz

up to 200m

Receiver

Please check the package and make sure the below items are

already in the box. If there's missed anything, please contact with the

distributor directly.

ROOK

ROOK Receiver 1pc

Receiver holder: 1pc

Hot shoe protector: 2pc

Manual: 1pc

Transmitter 1pc

A、B

、

→

A 、B

→

A 、C → B、C

→

→ C

→

A、 B、C

Turn power on/off:

Transmitter:

Receiver:

(Turn

power off)

Hold [ ] 2 seconds to turn on transmitter, then group LED light on

for 2 seconds, and show which current light. It can be used trigger the

flash and control shutter. You could turn off power by pressing [ ]

2 seconds again, then [LED light] blink red three times.Then power off.

Switch [Power/group switch] to A or B or C to turn on receiver

power; the receiver will be stayed in the current group and the

LED light blink as red every 2 seconds.

Switch [Power/group switch] to OFF; the receiver power is off,

and the light stop blinking.

(Turn

power on)

Hot shoe foot with

screw

Indicator

Light

Shutter release/test

button

Shutter release/test

button