Wireless Live View Remote Control 无线图像可视快门线 261008 V10.
Contents Overview Cautions before use Features of Expert Included items Name of each part Usage Battery Installation Turn power ON and OFF Sync Code-Matching Channel adjustment Holding Expert Transmitter Connect with the camera Switching Signal Source Enlarge and review Sleep/Wake-up mode 03 04 07 08 09 12 12 13 14 15 16 17 18 19 20 1
Contents LCD Brightness adjustment Volume adjustment Menu Remote Shooting PIXEL Expert Specifications Overview 20 20 21 23 24 Thank you very much for purchasing PIXEL high-performance product First of all, thank you for purchasing PIXEL's Expert. This is monitoring the lens view or the CMOS view on transmitter. Receiver side supports single shooting, [BULB] shooting and delay shooting.
Cautions before use Make sure the camera and Expert are powered off before install device. As this is an electronic product accessory; some of the environment causes may affect the working. However this is hardly ever to get this situation. When connected the remote cable with the device, do not pull the wires. This product can't be strong vibration, or may lead to product failure. For a long time non-use, please turned off the view transmitter and the receiver's power and remove the battery.
Cautions before use If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Included items Name of each part Please check all included items after open the packing, and PIXEL Expert with the following items: 1 2 3 4 5 Expert Transmitter Expert Transmitter 1 Code matching button 2 Power socket 1 pc Expert Receiver 1pc Instruction Manual 1 pc Shutter connecting cable Video Connecting Cable Canon or Nikon 2 pc 3 pc 2 pc 11 5 6 7 1 2 3 3 Power switch 4 Hot shoe locknut 12 5 Power LED indicator 8 9 10 13 6 Status LED indicator 7 Shooting LED indicator 8 Video/Audio s
Name of each part Name of each part Expert Receiver 5 1 6 12 2 3 4 8 OK 14 9 Screen brightness increase/right shift button 11 Screen brightness reduce/left shift button 14 USB Socket 10 13 AV/Audio 7 8 9 10 11 12 Power switch 1 2 MENU Button CMOS and camera view button 3 Video enlarge/Review button 4 Channel switch/sleep and wake-up button 5 Status LED indicator 6 Shutter 7 Volume up/Up shift button DC0 DC2 E3 2 Camera connecting side 1 A side ST Video Connecting Cable 10 V
Usage Usage Battery Installation 1. Slide and open battery hatch. Transmitter uses 4 AA batteries; available to use rechargeable or alkaline battery. 2. Install the battery according to the signs on the battery hatch. When using 1.2V 2400mA battery, standby for 100 hours, working time over 10 hours. When the battery is low, POWER LED INDICATOR would flash as red. The battery should be replaced or recharged immediately. 12 Turn power ON and OFF Transmitter and receiver both have a power switch.
Usage Sync Code-Matching 1. Press [MENU] enters to the menu. 2. Press the right or left button move to [SYNC] page. 3. Press the up or down button move to [YES]. 4. Press [OK], the STATUS LED flash as red, the screen shows [Syncing…], and then receiver gets into Sync Code-Matching. 5. Press and hold [Code] on transmitter for two sec, the STATUS LED flash red, and the transmitter gets into Sync Code-Matching. 6.
Usage Usage Connect with the camera Holding Expert Transmitter Available to hold the transmitter on hot shoe, rack or tripod. 1. Insert 1.Hold the transmitter on the hot shoe of camera. Lock the hot shoe locknuts. Loosen the hot shoe locknut first when you remove the transmitter. Do not forcibly pull out it, in order to avoid damage to the transmitter and camera. * The shutter cable has various models to match with different camera . 2.
Usage Switching Signal Source Receiver directs to convert the input signal source of transmitter. Press [CCTV/AV] when camera's LV mode is on and AV signal has connected to transmitter, the input signal source of transmitter will convert between AV and CCTV. Usage Enlarge and review 1. Under the CMOS mode, slightly press the Enlarge and Check button [ ] to enlarge display function, and the Screen display effect will be magnified one times. Press [up/down]/[right/left] to move the displaying scope.
Usage Usage Sleep/Wake-up mode Under operation status, hold [CHANNEL SWITCH/WAKE UP] for two sec, and the screen will get into sleeping mode. Under sleeping mode, hold [CHANNEL SWITCH/WAKE UP] for two sec, and the screen will get into monitor mode. *Setting sleep mode in menu. Menu 1. Press [MENU] to enter the menu. 2. Press [right/left] to select submenu. Press [up/down] to select items in submenu. 3. Press [OK] to execute the selected item.
Usage DRIVE SAVE Usage SYNC BEFORE AFTER SAVE: Screen shot saving setting: Save before taking the shot (BEFORE), Save 1.8 sec after taking the shot (AFTER), No saving (OFF). OFF AVOUT DRIVE SAVE SINGLE CONTINU DELAY 2 S VER AVOUT DRIVE TV TFT LCD VER AVOUT: Video output setting: External AV video interface (TV), LCD display screen (TFT LCD). *With connected external monitor, randomly to switch between the external monitor and the LCD display. AVOUT TX 000.000 RX 015.
PIXEL Expert Specifications Type: Distance: Transmitter: Receiver: Dimensions: (W×H×D) Weight: ISM 2.4GHz frequency channel which qualified CE or FCC standard. 200 meters Standby time: 100 hours Working time: 1 0 hours Standby time: 500 hours Working time: 12 hours Transmitter: 62.6mm×39.2mm×166mm Receiver: 12 2mm×27.9mm×73.4mm Transmitter: 88.5(without battery) Receiver: 128(without battery) Now you can start to use unique high-performance PIXEL product Expert.