ENGLISH BLACKVUE SPORT SC300
ENGLISH > Contents Introduction to the Manual Safety Precautions Checking the Components Getting Started Installing Camera Understanding the Part Name and Function Inserting/Removing the Memory Card Inserting/Removing the Battery Charging the Battery Assembling the LCD (not supplied) Camera Installation Installing the Camera inside a Waterproof Housing Connecting Power Cable 4 Shooting 5 8 10 12 13 14 15 17 Using the BLACKVUE SPORT APP Product Spe
> Introduction to the Manual Thank you for purchasing BLACKVUE SPORT of PittaSoft Co., Ltd. This instruction manual contains information on how to operate your BLACKVUE SPORT. Before using the product, make sure to read through this manual so as to use the product in the correct way. To enhance the performance of the product, the contents of this instruction manual may be changed without prior notice.
ENGLISH > Safety Precautions The purpose of these cautions is to maintain user safety and avoid damage to property. Please make sure to read through this manual so as to use the product in the correct way. DANGER Death or property damage can be caused for users if the following directions are not followed: yy Do not disassemble, repair, or modify the product yourself. It can cause fire, electric shock, or malfunction. For internal inspection and repair, call your customer service center.
WARNING Death or serious injury can be caused for users if the following directions are not followed: yy Do not leave the product where infants, children, or pets can reach it. yy Do not cover the product with any material. They might swallow small components, or their saliva could get into it and cause an explosion due to a short circuit. It can cause external deformation of the product or fire. Use the product and peripherals where ventilation is ensured.
Injury or property damage can be caused for users if the following directions are not followed: yy Do not spray cleaning products directly onto the outside of the product. It can cause discoloration, cracks, or malfunction. yy Make sure that the product is installed properly. The product can fall as a result of vibration, and may cause physical injury. yy MicroSD cards are a consumable so replace them after prolonged use.
> Getting Started I Checking the Components After purchasing the camera, open the box and check the following components.
ENGLISH Accessories (Sold separately) LCD pack for bike (LCD, Waterproof housing backdoor for LCD) Waterproof housing Basic connector Tripod mount Cable connector Curved mount Joint rubber for single cable Thumb screw Handlebar mount Note yy The image of each component or accessory may differ from the actual component or accessory. yy To enhance the performance of the product, the components of this product may be changed without prior notice.
I Understanding the Part Name and Function Check the name and function of each part first before using the camera.
Description Shooting mode: Start/End shooting Playback mode* • Thumbnail view: Select a file • Playback or Pause* Setting mode*: Select a menu or setting item Wi-Fi On/Off: Long press Power On/Off: Long press Mode change: Press • * Movie/Normal Photo/High-speed Shooting/Playback/ Setting • *Switching between menus or setting items Item Description VIDEO Blue: Movie/Time Lapse mode PHOTO Blue: Photo shooting mode HIGH SPEED Blue: High speed shooting mode Wi-Fi Blue: Wi-Fi power on Off: Wi-Fi power of
I Inserting/Removing the Memory Card Inserting the memory card 1 Open the cover of the memory card slot. 3 Close the cover of the memory card slot. Note Be careful not to lose the cover for the memory card slot. Removing the memory card 2 Insert the memory card with the metallic terminal to the left. Press the memory card in lightly, and when the top emerges part way, pull it out completely.
ENGLISH I Inserting/Removing the Battery Inserting the battery 1 Open the battery cover. 2 Insert the batteries. 3 Close the battery cover. Removing the Battery Remove the battery by holding and lifting the plastic handle on the opposite side of the metallic terminal.
I Charging the Battery Charging by Connecting the Battery Charger (not supplied) Charge the battery completely when using the camera for the first time after purchasing it. Charging by connecting the USB cable to a PC (not supplied) (Not supplied) Note Use only authentic, manufacturer-recommended, Lithium-ion replacement batteries or supplied battery charger. Otherwise, PittaSoft Co., Ltd. will not be held responsible for any problem.
You can check the shooting scene, play back a file, or set the camera and shooting environments by mounting the LCD component to the camera. Name of each part in the LCD Assembling the LCD LCD power button Align the assembly groove on the LCD with the right end of the camera, and insert the connection terminal of the LCD into the connection terminal of the camera correctly.
Removing the LCD Remove the LCD by pulling the part marked with an arrow firmly upwards. Note After assembling the LCD, turn on the camera and check the LCD operates normally. If the LCD screen does not turn on, turn off the camera and assemble the LCD again using the method specified on the previous page.
ENGLISH > Installing Camera I Camera Installation Using a mount, you can install the camera on a bike. Installation Using an Adhesive Tape Attach the adhesive tape to where you want to place the camera, and then mount or use the curved mount for the tripod to affix the camera onto it. Camera Installation Using a Handle Bar Mount (not supplied) You can install the camera onto the handle via a handle bar mount and affix the camera using a tripod mount.
I Installing the Camera inside a Waterproof Housing By placing the camera inside a waterproof housing, you can protect your camera from external hazards (dust and water). Camera installation method is the same as the slim-type backdoor and backdoor for LCD. 1 2 3 Before placing the camera inside the waterproof housing, ensure that you have powered off the camera. 4 Couple the groove in the lock with the groove in the rear cover. 5 Turn the lock counter clockwise to the fullest and lower the latch.
Using the waterproof housing and waterproof power cable, you can draw power from the bike’s cigar jack when it rains. Cigar jack Converter 1 Turn connector screw clockwise and remove the S-washer and cable joint rubber. 2 Insert the micro USB connector of the waterproof power cable into the cable joint rubber for single cable. 3 Insert the cable joint rubber, assembled into the connector.
4 6 Turn the extension cable screw of waterproof housing clockwise and remove the extension cable cover. Insert the S-washer with the narrow side facing upwards and turn the cable connector joint screw clockwise. Note 5 Using a joint rubber for multi cable, you can connect both the HDMI cable (not supplied) and the power cable at the same time. Connect the cable connector you have assembled in your camera.
1 Firmly mount the waterproof housing that holds the camera onto your bike. Note When you have no cigar jack power, cut the waterproof power cable and connect it directly to the battery, make sure that you do not cut the middle of the converter or the connector jack. yy You can use a curved mount or a handle bar mount (not supplied) for this purpose. 2 Cigar jack Plug the waterproof power cable connector jack in the direction, as indicated by the arrow.
Removing Cable after Using the Camera When you are done with using the camera, detach periferals, and keep the camera, you do not need to remove all cables from you bike. Remove cables in a place free from water, sand, or dust. 1 Disconnect the connector jacks of waterproof power cable. 2 3 Keep the disconnected camera and cables indoorse. Keep the connector jack installed on your bike with a cap plugged.
After charging the battery, press and hold down on. yy Press and hold down I Automatic Video Recording until the camera turns again to turn off the camera. If you have ther camera connected to the bike power supply, you can record video during the entirel time you are biking. Up to full HD image resolution with 1920 x 1080 pixels at 30fps, video images are recorded in the MP4 format. 1 Press 2 3 Press to start video recording. Press once again to end video recording. and select the video mode.
> Using the BLACKVUE SPORT APP You can control or manage the camera from a wireless device (smartphone or tablet PC) where the BLACKVUE SPORT App is installed. 1 Install and execute BLACKVUE SPORT App on a wireless device. Note yy The BLACKVUE SPORT App can be downloaded from the Google Play store and Apple App Store. yy The BLACKVUE SPORT App can be used with Android 2.3 or later and iOS 5.0 or later. yy Some functions may not be supported depending on the wireless device.
ENGLISH Note iOS yy Wi-Fi SSID can be changed from the App Settings. yy If you save the connection information when connecting using WiFi, you can tap the Wi-Fi button in the BLACKVUE SPORT App to connect it without turning on the Wi-Fi function of the smartphone. (only for Android) yy The initial password is blackvue, but the user can change it. yy For the Live View function, Wi-Fi can be used within a 10m range, although the range may vary in some circumstances.
I Screen View 1 2 3 4 No. Descriptions 1 Moves to the Home screen. 6 Shoots a movie or take a picture. 2 Moves to the internal memory. 7 Watches the shooting screen in real time. 3 Displays the captured screen in real time. 8 Moves to the list of movies/ pictures. 7 4 Changes the mode. 9 Moves to the setting screen. 6 5 Displays the setting options of the camera. : Allows you to check the version information. : 9 8 5 Drag the top bar to display. No.
ENGLISH I Changing the Setting Option 1 Press BlackVue Sport ▶ SETTINGS ▶ App Settings or Camera Settings to access the setting screen. 2 3 Select a desired setting menu, and select the setting to change. Android iOS Press Save to save the setting. Press EXIT to return to the previous screen without saving the setting. Note yy If you have changed Wi-Fi settings, always restart the camera. yy The date is originally set to default. You can set the date manually by connecting with BLACKVUE SPORT APP.
Setting Option Mode Menu Setting Option Mode Menu On Always use BlackVue S player Off App Settings On Enable Wi-Fi Strength Monitor Image Quality Camera Settings Photo Settings Burst Shot Off Resolution/FPS Setting Option Resolution Self Timer Image Settings Rotation Video Quality Camera Settings Video Settings Time Lapse Recording Time Overwrite Note You can reverse the LCD screen by activating Rotation in the Image Settings.
Menu ENGLISH Mode Setting Option Date/Time Wi-Fi Voice Record Camera Settings Volume Other Settings Automatic Recovery Auto Power Off Default Setting Format BLACKVUE SPORT I SC300 29
I Playing Movies/Photos 1 2 Press BlackVue Sport ▶ LIST ▶ 100BVSCM. Select a desired movie or photo. I Moving files 1 2 Press BlackVue Sport ▶ LIST ▶100BVSCM. 3 Press Copy files to internal storage to move the selected file to the internal memory. Select a desired file, and press and hold down the file until the menu is displayed.
ENGLISH I Managing the internal memory 1 2 Press Internal Memory. yy Cancel: Returns to the previous screen. Select a desired file, and press and hold down the file until the menu is displayed. yy Copy: Copies the selected video/photo. 3 Press each menu to edit the selected file. yy Rename: Renames the video/photo you have selected. yy Cut: Cuts the selected video/photo. yy Delete: Deletes the selected video/photo.
I Firmware Upgrade 4 Detach the microSD card from the microSD card reader, and insert the microSD card into the camera. 5 When the power is turned on, it is automatically upgraded. You can upgrade the firmware version by saving the firmware to a microSD card and connecting the microSD card into the PC. 1 Access the BLACKVUE SPORT web site (www.blackvuesport.com) and download the firmware upgrade file. 2 Insert the provided microSD card into a microSD card reader.
ENGLISH > Product Specifications To enhance the performance of the product, the product specifications may be changed without prior notice. Model Camera 3.5 Mega Pixel Angle of View Opposite Angle 138˚ Weight 77g (LCD : 22g) Size (WxLxH) 55mm x 36.7mm x 44.2mm Sensor 3.5M CMOS Sensor Storage H/W Interface BLACKVUE SPORT Pixel micro SD Card Input/Output USB 2.0 / USB 2.0, HDMI Button Power/Mode, Wi-Fi, Shutter/Choice LCD 2.
Wi-Fi Audio Software 13 Channel 802.11b/g/n(20) 9 Channel 802.11n(40) PCM DSSS(CCK), OFDM(QAM) Mic Built-in, Mono Format 128kHz, AAC Application BLACKVUE SPORT APP Degree IP68 Depth Rate 10m / 32ft Waterproof Frontcase (basic) Housing Backdoor (for LCD) Android 2.3 or later, iOS 5.
FCC Compliance Information (FCC ID: YCK-SC300) THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. Operation is subject to the following two conditions; (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Product Warranty The term of this product warranty is 1 year from the purchase date. (Accessories such as Battery : 6 Months) We, PittaSoft Co., Ltd., provide the product warranty according to Consumer Dispute Settlement Regulations (drawn up by the Fair Trade Commission). PittaSoft or designated partners will provide the service upon request. Product Name (Model Name) Serial No.
Consumer Injury For performance / functional problems under normal use conditions Repair If Available For Defect Warranty Within the Term Free Repair Repeated problem with the same defect (up to 3 times) Repeated trouble with different parts (up to 5 times) For the loss of a product while in A/S Repair If Unavailable When repair is unavailable due to lack of spare parts within the component holding period Exchange/Refund This warranty is only valid in the country where you purchased the product.
MEMO
MEMO
Name Ι BLACKVUE SPORT Manufacturer Ι Pittasoft Co.,Ltd. / South Korea Address Ι (Gasan-dong, BYC HIGHCITY), A-7th floor, 131, Gasan digital 1-ro, Geumcheon-gu, Seoul, 153-718, Republic of Korea E-mail Ι sales@pittasoft.com Service Center Ι +82.2.6947.4670(ext.3) www.blackvuesport.
