IPsec NAT-T https://www.peplink.com This field is for enabling the support of IPsec NAT-T passthrough. UDP ports 500, 4500, and 10000 are monitored by default. You may add more custom data ports that your IPsec system uses by checking Define custom ports. If the VPN contains IPsec site-to-site VPN traffic, check Route IPsec Site-to-Site VPN and choose the WAN connection to route the traffic to.
4.5 UART Selected Pepwave MAX routers feature a RS-232 serial interface on the built-in terminal block. The RS-232 serial interface can be used to connect to a serial device and make it accessible over an TCP/IP network. The serial interface can be enabled and parameters can be set on the web admin page under Advanced > UART. Make sure they match the serial device you are connecting to. https://www.peplink.
There are 4 pins i.e. TX, RX, RTS, CTS on the terminal block for serial connection and they correspond to the pins in a DB-9 connector as follows: DB-9 Pepwave MAX Terminal Block Pin 1 – Pin 2 Rx (rated -+25V) Pin 3 Tx (rated -+12V) Pin 4 – Pin 5 – Pin 6 – Pin 7 RTS Pin 8 CTS Pin 9 – The RS232 serial interface is not an isolated RS232. External galvanic isolation may be added if required.
24.6 GPS Forwarding Using the GPS forwarding feature, some Pepwave routers can automatically send GPS reports to a specified server. To set up GPS forwarding, navigate to Advanced>GPS Forwarding. GPS Forwarding Enable Check this box to turn on GPS forwarding. Server Enter the name/IP address of the server that will receive GPS data. Also specify a port number, protocol (UDP or TCP), and a report interval of between 1 and 10 seconds. Click GPS Report Format to save these settings.
24.7 Ignition Sensing Ignition Sensing detects the ignition signal status of a vehicle it is installed in. This feature allows the cellular router to start up or shut down when the engine of that vehicle is started or turned off. The time delay setting between ignition off and power down of the router is a configurable setting, which allows the router to stay on for a period of time after the engine of a vehicle is turned off.
Connectivity diagram for devices with 4-pin connector Connectivity diagram for devices with terminal block connection https://www.peplink.
GPIO Menu Note: This feature is applicable for certain models that come with a GPIO interface. Ignition Sensing options can be found in Advanced > GPIO. The configurable option for Ignition Input is Delay; the time in seconds that the router stays powered on after the ignition is turned off. The O/P (connected to the I/O pin on a 4 pin connector) can be configured as a digital input, a digital output, or an analog input.
24.8 NTP Server Pepwave routers can now serve as a local NTP server. Upon start up, it is now able to provide connected devices with the accurate time, precise UTC from either an external NTP server or via GPS and ensuring that connected devices always receive the correct time. Compatible with: BR1 ENT, BR1 Pro CAT-20/5G, 700 HW3, HD2/4, Transit NTP Server setting can be found via: Advanced>Misc. Settings>NTP Server Time Settings can be found at System>Time>Time Settings https://www.peplink.
24.9 Grouped Networks Advanced > Grouped Networks allows to configure destination networks in grouped format. Select Add group to create a new group with single IPaddresses or subnets from different VLANs. The created network groups can be used in outbound policies, firewall rules. https://www.peplink.
24.10 Remote SIM Management The Remote SIM management is accessible via Advanced > Misc Settings > Remote SIM Management. By default, this feature is disabled. Please note that a limited number of Pepwave routers support the SIM Injector, may refer to the link: https://www.peplink.com/products/sim-injector/ or Appendix B for more details on FusionSIM Manual. Remote SIM Host Settings Remote SIM Host Settings Active LAN Discovery Check this box to enable Auto LAN discovery of the remote SIM server..
Add Remote SIM Settings SIM Server Add a new SIM Server SIM Server - Serial Number Enter the serial number of SIM Server SIM Server - Name This optional field allows you define a name for the SIM Server SIM Slot SIM Slot - Name Data Roaming Click the drop-down menu and choose which SIM slot you want to connect. This optional field allows you define a name for the SIM slot. Enables data roaming on this particular SIM card. This setting allows you to configure the APN settings of your connection.
24.11 SIM Toolkit The SIM Toolkit, accessible via Advanced > Misc Settings > SIM Toolkit, supports two functionalities, USSD and SMS. USSD Unstructured Supplementary Service Data (USSD) is a protocol used by mobile phones to communicate with their service provider’s computers. One of the most common uses is to query the available balance. Enter your USSD code under the USSD Code text field and click Submit. You will receive a confirmation. To check the SMS response, click Get.
SMS The SMS option allows you to read SMS (text) messages that have been sent to the SIM in your Pepwave router. https://www.peplink.
25 AP 25.1 AP Controller The AP controller acts as a centralized controller of Pepwave Access Points. With this feature, users can customize and manage up to 1500 Access Points from a single Pepwave router interface. To configure, navigate to the AP tab. and the following screen appears. AP Controller The AP controller for managing Pepwave APs can be enabled by checking this box.
SSID Settings SSID Enable VLAN https://www.peplink.com This setting specifies the SSID of the virtual AP to be scanned by Wi-Fi clients. Click the drop-down menu to apply a time schedule to this interface This setting specifies the VLAN ID to be tagged on all outgoing packets generated from this wireless network (i.e., packets that travel from the Wi-Fi segment through the Pepwave AP One unit to the Ethernet segment via the LAN port).
Broadcast SSID This setting specifies whether or not Wi-Fi clients can scan the SSID of this wireless network. Broadcast SSID is enabled by default. Data Rate A Select Auto to allow the Pepwave router to set the data rate automatically, or select Fixed and choose a rate from the displayed drop-down menu. Multicast FilterA This setting enables the filtering of multicast network traffic to the wireless SSID.
● ● WPA/WPA2 - Personal (TKIP/AES: CCMP) WPA/WPA2 – Enterprise When WPA/WPA2 - Enterprise is configured, RADIUS-based 802.1 x authentication is enabled. Under this configuration, the Shared Key option should be disabled. When using this method, select the appropriate version using the V1/V2 controls. The security level of this method is known to be very high. When WPA/WPA2- Personal is configured, a shared key is used for data encryption and authentication.
RADIUS Server Settings Host Enter the IP address of the primary RADIUS server and, if applicable, the secondary RADIUS server. Secret Enter the RADIUS shared secret for the primary server and, if applicable, the secondary RADIUS server. Authentication In the field, enter the UDP authentication port(s) used by your RADIUS server(s) or click the Default button to enter 1812.
Firewall Settings Firewall Mode The settings allow administrators to control access to the SSID based on Firewall Rules. Available options are Disable, Lockdown - Block all except... and Flexible -Allow all except… Firewall Exceptions Create Firewall Rules based on Port, IP Network, MAC address or Domain Name 25.3 Wireless Mesh Wireless Mesh Support is available on devices running 802.11ac (Wi-Fi 5) and above.
25.4 Settings On many Pepwave models, the AP settings screen (AP>Settings) looks similar to the example below: AP Settings SSID https://www.peplink.com These buttons specify which wireless networks will use this AP profile. You can also select the frequencies at which each network will transmit. Please note that the Pepwave MAX does not detect whether the AP is capable of transmitting at both frequencies. Instructions to transmit at unsupported frequencies will be ignored by the AP.
This drop-down menu specifies the national / regional regulations which the AP should follow. ● If a North American region is selected, RF channels 1 to 11 will be available and the maximum transmission power will be 26 dBm (400 mW). ● If European region is selected, RF channels 1 to 13 will be available. Operating Country The maximum transmission power will be 20 dBm (100 mW). Note: Users are required to choose an option suitable to local laws and regulations.
Max number of ClientsA This field determines the maximum clients that can be connected to APs under this profile. This field specifies the VLAN ID to tag to management traffic, such as AP to AP controller communication traffic. The value is 0 by default, meaning that no Management VLAN VLAN tagging will be applied. ID Note: change this value with caution as alterations may result in loss of connection to the AP controller.
The device with integrated AP can operate under the Wi-Fi Operating Mode, and the default setting is WAN + AP mode: Note: This option is available for selected devices only (HD2/HD4 and HD2/HD4 MBX). Integrated AP In this mode, all Wi-Fi will operate as Wi-Fi WAN and no integrated Wi-Fi AP will be operated on this device. WAN If Wi-Fi Operating mode is choosing WAN, The status indicated by the front panel LED is as follows: - Wi-Fi 1 is Green if Wi-Fi WAN 1 is enabled.
Web Administration Settings Enable Check the box to allow the Pepwave router to manage the web admin access information of the AP. Web Access Protocol These buttons specify the web access protocol used for accessing the web admin of the AP. The two available options are HTTP and HTTPS. Management Port This field specifies the management port used for accessing the device. HTTP to HTTPS Redirection This option will be available if you have chosen HTTPS as the Web Access Protocol.
Important Note Per FCC regulations, the country selection is not available on all models marketed in the US. All US models are fixed to US channels only. Wi-Fi AP Settings A Protocol This option allows you to specify whether 802.11b and/or 802.11g client association requests will be accepted. Available options are 802.11ng and 802.11na. By default, 802.11ng is selected. Channel This option allows you to select which 802.11 RF channel will be used. Channel 1 (2.412 GHz) is selected by default.
AP Controller Status 26.1 Info A comprehensive overview of your AP can be accessed by navigating to AP > Controller Status > Info. AP Controller License Limit This field displays the maximum number of AP your Balance router can control. You can purchase licenses to increase the number of AP you can manage. Frequency Underneath, there are two check boxes labeled 2.4 Ghz and 5 Ghz. Clicking either box will toggle the display of information for that frequency.
given time. Mouse over any line on the graph to see how many clients connected to a specific SSID for that point in time. Data Usage This graph enables you to see the data usage of any SSID for any given time period. Mouse over any line on the graph to see the data usage by each SSID for that point in time. Use the buttons next to Zoom to select the time scale you wish to view. In addition, you could use the sliders at the bottom to further refine your timescale.
26.2 Access Point (Usage) A detailed breakdown of data usage for each AP is available at AP > Controller Status > Access Point. Usage AP Name/Serial Number Online Status This field enables you to quickly find your device if you know its name or serial number. Fill in the field to begin searching. Partial names and serial numbers are supported. This button toggles whether your search will include offline devices.
For easier network management, you can give each client a name and designate its location. You can also designate which firmware pack (if any) this client will follow, as well as the channels on which the client will broadcast. Click the icon to see a graph displaying usage: Click any point in the graphs to display detailed usage and client information for that device, using that SSID, at that point in time. On the Data Usage by menu, you can display the information by SSID or by AP send/receive rate.
particular device: 26.3 Wireless SSID In-depth SSID reports are available under AP > Controller Status > Wireless SSID. https://www.peplink.
Click the blue arrow on any SSID to obtain more detailed usage information on each SSID. 26.4 Mesh / WDS Mesh / WDS allows you to monitor the status of your wireless distribution system (WDS) or Mesh, and track activity by MAC address by navigating to AP > Controller Status > Mesh / WDS. This table shows the detailed information of each AP, including protocol, transmit rate (sent / received), signal strength, and duration. https://www.peplink.
26.5 Wireless Client You can search for specific Wi-Fi users by navigating to AP > Controller Status > Wireless Client. Here, you will be able to see your network’s heaviest users as well as search for specific users. Click the icon to bookmark specific users, and click the icon for additional details about each user: https://www.peplink.
https://www.peplink.
26.6 Nearby Device A listing of near devices can be accessed by navigating to AP > Controller Status > Nearby Device. Suspected Rogue Devices Hovering over the device MAC address will result in a popup with information on how this device was detected. Click the icons and the device will be moved to the bottom table of identified devices. 26.7 Event Log You can access the AP Controller Event log by navigating to AP > Controller Status > Event Log. https://www.peplink.
Events This event log displays all activity on your AP network, down to the client level. Use to filter box to search by MAC address, SSID, AP Serial Number, or AP Profile name. Click View Alerts to see only alerts, and click the More… link for additional records. 27 Toolbox Tools for managing firmware packs can be found at AP>Toolbox. Firmware Packs Here, you can manage the firmware of your AP. Clicking on will result in information regarding each firmware pack.
28 System Settings 28.1 Admin Security There are two types of user accounts available for accessing the web admin: admin and user. They represent two user levels: the admin level has full administrative access, while the user level is read-only. The user level can access only the device's status information; users cannot make any changes on the device. A web login session will be logged out automatically when it has been idle longer than the Web Session Timeout.
Admin Settings Router Name Admin User Name This field allows you to define a name for this Pepwave router. By default, Router Name is set as MAX_XXXX, where XXXX refers to the last 4 digits of the unit’s serial number. Admin User Name is set as admin by default, but can be changed, if desired. Admin Password This field allows you to specify a new administrator password. Confirm Admin This field allows you to verify and confirm the new administrator password.
Web Session Timeout This field specifies the number of hours and minutes that a web session can remain idle before the Pepwave router terminates its access to the web admin interface. By default, it is set to 4 hours. Authentication by RADIUS With this box is checked, the web admin will authenticate using an external RADIUS server. Authenticated users are treated as either "admin" with full read-write permission or “user” with read-only access. Local admin and user accounts will be disabled.
be accessed. This option is for specifying the network interfaces through which the web admin interface can be accessed: Web Admin Access ● LAN only ● LAN/WAN If LAN/WAN is chosen, the WAN Connection Access Settings form will be displayed. LAN Connection Access Settings Allowed LAN Networks This field allows you to permit only specific networks or VLANs to access the Web UI. WAN Connection Access Settings This field allows you to restrict web admin access only from defined IP subnets.
32 inclusively (For example, 192.168.0.0/24). To define multiple subnets, separate each IP subnet one in a line. For example: ● ● Allowed WAN IP Address(es) 192.168.0.0/24 10.8.0.0/16 This is to choose which WAN IP address(es) the web server should listen on. 28.2 Firmware Web admin interface : automatically check for updates Upgrading firmware can be done in one of three ways.
The firmware will now be applied to the router*. The amount of time it takes for the firmware to upgrade will also depend on the router that’s being upgraded. *Upgrading the firmware will cause the router to reboot. Web admin interface : install updates manually In some cases, a special build may be provided via a ticket or it may be found in the forum. Upgrading to the special build can be done using this method, or using IC2 if you are using that to manage your firmware upgrades.
A prompt will be displayed advising to download the Current Active Configuration. Please click on the underlined download text. After downloading the current config click the Ok button to start the upgrade process. The firmware will now be applied to the router*. The amount of time it takes for the firmware to upgrade will depend on the router that’s being upgraded. *Upgrading the firmware will cause the router to reboot. The InControl method Described in this knowledgebase article on our forum. 28.
Time Server This setting specifies the NTP network time server to be utilized by the Pepwave router. 28.4 Schedule Enable and disable different functions (such as WAN connections, outbound policy, and firewalls at different times, based on a user-scheduled configuration profile. The settings for this are located at System > Schedule Enable scheduling, and then click on your schedule name or on the New Schedule button to begin. Edit Schedule Profile Enabling https://www.peplink.
Name Enter your desired name for this particular schedule profile. Schedule Click the drop-down menu to choose pre-defined schedules as your starting point. Please note that upon selection, previous changes on the schedule map will be deleted. Schedule Map Click on the desired times to enable features at that time period. You can hold your mouse for faster entry. 28.5 Email Notification Email notification functionality provides a system administrator with up-to-date information on network status.
● ● ● SMTP Port None STARTTLS SSL/TLS This field is for specifying the SMTP port number. By default, this is set to 25. If Connection Security is selected “STARTTLS”, the default port number will be set to 587. If Connection Security is selected “SSL/TLS”, the default port number will be set to 465. You may customize the port number by editing this field. SMTP User Name / Password This setting specifies the SMTP username and password while sending email.
https://www.peplink.
28.6 Event Log Event log functionality enables event logging at a specified remote syslog server. The settings for configuring the remote system log can be found at System>Event Log. Event Log Settings Remote Syslog This setting specifies whether or not to log events at the specified remote syslog server. Remote Syslog Host This setting specifies the IP address or hostname of the remote syslog server.
Session Logging This setting specifies the IP address or hostname of the Session log server. Host For more information on www.peplink.com/products/router-utility the Router Utility, go to: 28.7 SNMP SNMP or simple network management protocol is an open standard that can be used to collect information about the Pepwave router. SNMP configuration is located at System>SNMP. SNMP Settings SNMP Device Name SNMP Port https://www.peplink.
SNMPv1 This option allows you to enable SNMP version 1. SNMPv2 This option allows you to enable SNMP version 2. SNMPv3 This option allows you to enable SNMP version 3. SNMP Trap This option allows you to enable SNMP Trap. If enabled, the following entry fields will appear. SNMP Trap Community This setting specifies the SNMP Trap community name. SNMP Trap Server Enter the IP address of the SNMP Trap server. This option specifies the port which the SNMP Trap server will use.
Allowed Source This setting specifies a subnet from which access to the SNMP server is allowed. Enter subnet address here (e.g., 192.168.1.0) and select the appropriate subnet Subnet Address mask. To define a user name for SNMPv3, click Add SNMP User in the SNMPv3 User Name table, upon which the following screen is displayed: SNMPv3 User Settings User Name This setting specifies a user name to be used in SNMPv3.
SMS Control Settings Enable Click the checkbox to enable the SMS Control. Password This setting sets the password for authentication - maximum of 32 characters, which cannot include semicolon (;). White List Optionally, you can add phone number(s) to the whitelist. Only matching phone numbers are allowed to issue SMS commands. Phone numbers must be in the E.164 International Phone Numbers format. 28.
You can sign up for an InControl account at https://incontrol2.peplink.com/. You can register your devices under the account, monitor their status, see their usage reports, and receive offline notifications. 28.10 Configuration Backing up Pepwave router settings immediately after successful completion of initial setup is strongly recommended. The functionality to download and upload Pepwave router settings is found at System>Configuration. Note that available options vary by model.
the settings, configure the LAN IP address of the Pepwave router so that it is from High different from the HA counterpart. Availability Pair 28.11 Feature Add-ons Some Pepwave routers have features that can be activated upon purchase. Once the purchase is complete, you will receive an activation key. Enter the key in the Activation Key field, click Activate, and then click Apply Changes. 28.12 Reboot This page provides a reboot button for restarting the system.
29 Tools 29.1 Ping The ping test tool sends pings through a specific Ethernet interface or a SpeedFusionTM VPN connection. You can specify the number of pings in the field Number of times, to a maximum number of 10 times. Packet Size can be set to a maximum of 1472 bytes. The ping utility is located at System>Tools>Ping, illustrated below: Tip A system administrator can use the ping utility to manually check the connectivity of a particular LAN/WAN connection. https://www.peplink.
29.2 Traceroute Test The traceroute test tool traces the routing path to the destination through a particular Ethernet interface or a SpeedFusionTM connection. The traceroute test utility is located at System>Tools>Traceroute. Tip A system administrator can use the traceroute utility to analyze the connection path of a LAN/WAN connection. 29.3 PepVPN Test The PepVPN Test tool can help to test the throughput between different VPN peers.
29.4 Wake-on-LAN Peplink routers can send special “magic packets” to any client specified from the Web UI. To access this feature, navigate to System > Tools > Wake-on-LAN Select a client from the drop-down list and click Send to send a “magic packet” 29.5 CLI (Command Line Interface Support) The CLI (command line interface) can be accessed via SSH. This field enables CLI support. The below settings specify which TCP port and which interface(s) should accept remote SSH CLI access.
30 Status 30.1 Device System information is located at Status>Device. System Information Device Name Model Product Code Hardware Revision https://www.peplink.com This is the name specified in the Device Name field located at System>Admin Security. This shows the model name and number of this device. If your model uses a product code, it will appear here. This shows the hardware version of this device.
Serial Number Firmware This shows the serial number of this device. This shows the firmware version this device is currently running. PepVPN Version This shows the current PepVPN version. Modem Support This shows the modem support version. For a list of supported modems, click Modem Support List. Version InControl Managed Configuration Host Name Uptime System Time InControl Managed Configurations (firmware, VLAN, Captive Portal, etcetera) The host name assigned to the Pepwave router appears here.
30.2 GPS Data GPS enabled models automatically store up to seven days of GPS location data in GPS eXchange format (GPX). To review this data using third-party applications, click Status>Device and then download your GPX file. The Pepwave GPS enabled devices export real-time location data in NMEA format through the LAN IP address at TCP port 60660. It is accessible from the LAN or over a SpeedFusion connection. To access the data via a virtual serial port, install a virtual serial port driver.
30.3 Active Sessions Information on active sessions can be found at Status>Active Sessions>Overview. This screen displays the number of sessions initiated by each application. Click on each service listing for additional information. This screen also indicates the number of sessions initiated by each WAN port. In addition, you can see which clients are initiating the most sessions. You can also perform a filtered search for specific sessions. You can filter by subnet, port, protocol, and interface.
This Active Sessions section displays the active inbound/outbound sessions of each WAN connection on the Pepwave router. A filter is available to sort active session information. Enter a keyword in the field or check one of the WAN connection boxes for filtering. https://www.peplink.
30.4 Client List The client list table is located at Status>Client List. It lists DHCP and online client IP addresses, names (retrieved from the DHCP reservation table or defined by users), current download and upload rate, and MAC address. Clients can be imported into the DHCP reservation table by clicking the right. You can update the record after import by going to Network>LAN. button on the If the PPTP server (see Section 19.2), SpeedFusionTM (see Section 12.
You may also unblock the Wi-Fi or Remote User Access clients when the client devices need to reconnect the network by clicking the button on the right. 30.5 WINS Client The WINS client list table is located at Status>WINS Client. The WINS client table lists the IP addresses and names of WINS clients. This option will only be available when you have enabled the WINS server (navigation: Network>Interfaces>LAN).
Click to delete a single UPnP / NAT-PMP record in its corresponding row. To delete all records, click Delete All on the right-hand side below the table. Important Note UPnP / NAT-PMP records will be deleted immediately after clicking the button need to click Save or Confirm. or Delete All, without the 30.7 OSPF & RIPv2 Shows status of OSPF and RIPv2 https://www.peplink.
30.8 BGP Shows status of BGP 30.9 SpeedFusion Status Current SpeedFusionTM status information is located at Status>SpeedFusionTM. Details about SpeedFusionTM connection peers appears as below: Click on the corresponding peer name to explore the WAN connection(s) status and subnet information of each VPN peer. https://www.peplink.
Click the button for a SpeedFusion chart displaying real-time throughput, latency, and drop-rate information for each WAN connection. https://www.peplink.
When pressing the button, the following menu will appear: The Speedfusion status page shows all related information about the PepVPN connection. This screen also allows you to run PepVPN Tests allowing throughput tests. Peplink also published a whitepaper about Speedfusion which can be downloaded from the following url: http://download.peplink.com/resources/whitepaper-speedfusion-and-best-practices-2019.pdf https://www.peplink.
30.10 Event Log Event log information is located at Status>Event Log. The log section displays a list of events that has taken place on the Pepwave router. Check Auto Refresh to refresh log entries automatically. Click the Clear Log button to clear the log. https://www.peplink.
31 WAN Quality The Status > WAN Quality allow to show detailed information about each connected WAN connection. For cellular connections it shows signal strength, quality, throughput and latency for the past hour. https://www.peplink.
32 Usage Reports This section shows bandwidth usage statistics and is located at Status > Usage Reports Bandwidth usage at the LAN while the device is switched off (e.g., LAN bypass) is neither recorded nor shown. 32.1 Real-Time The Data transferred since installation table indicates how much network traffic has been processed by the device since the first bootup. The Data transferred since last reboot table indicates how much network traffic has been processed by the device since the last bootup.
32.2 Hourly This page shows the hourly bandwidth usage for all WAN connections, with the option of viewing each individual connection. Select the desired connection to check from the drop-down menu. https://www.peplink.
32.3 Daily This page shows the daily bandwidth usage for all WAN connections, with the option of viewing each individual connection. Select the connection to check from the drop-down menu. If you have enabled the Bandwidth Monitoring feature, the Current Billing Cycle table for that WAN connection will be displayed. Click on a date to view the client bandwidth usage of that specific date. This feature is not available if you have selected to view the bandwidth usage of only a particular WAN connection.
32.4 Monthly This page shows the monthly bandwidth usage for each WAN connection. If you have enabled the Bandwidth Monitoring feature, you can check the usage of each particular connection and view the information by Billing Cycle or by Calendar Month. Click the first two rows to view the client bandwidth usage in the last two months. This feature is not available if you have chosen to view the bandwidth of an individual WAN connection.
Ethernet WAN Monthly Bandwidth Usage Tip By default, the scale of data size is in MB. 1GB equals 1024MB. https://www.peplink.
Appendix A: Restoration of Factory Defaults To restore the factory default settings on a Pepwave router, follow the steps below: 1. Locate the reset button on the front or back panel of the Pepwave router. 2. With a paperclip, press and keep the reset button pressed. Note: There is a dual function to the reset button.
Appendix B: FusionSIM Manual Peplink has developed a unique technology called FusionSIM, which allows SIM cards to remotely link to a cellular router. This can be done via cloud or within the same physical network. There are a few key scenarios to fit certain applications. The purpose of this manual is to provide an introduction on where to start and how to set up for the most common scenarios and uses. Requirements 1. A Cellular router that supports FusionSIM technology 2. SIM Injector 3.
Scenario 1: SIM Injector in LAN of Cellular Router Setup topology This is the most basic scenario in which the SIM Injector is connected directly to the cellular router’s LAN port via an ethernet cable. This allows for the cellular router to be positioned for the best possible signal. Meanwhile, the SIM cards can be conveniently located in other locations such as the office, passenger area, or the bridge of a ship.
Configuring the Cellular Router Step 1. Enable the SIM Injector communication protocol. 1a. If you are using a Balance cellular router, go to the Network tab (top navigation bar). 1b. If you are using a MAX cellular router, go to the Advanced tab (top navigation bar). 2. Under Misc. settings (left navigation bar) find Remote SIM Management. 3. In Remote SIM Management, click on the edit icon next to Remote SIM is Disabled. 4. Check the Auto LAN discovery checkbox and click Save and Apply Changes. 5.
4. Enter configuration settings in Remote SIM Settings section. Click on Scan nearby remote SIM server to show the serial number(s) of the connected SIM Injector(s). Available configuration options for cellular interface are shown below: A. Defining SIM Injector(s) - Format: - Example 1: 1111-2222-3333 - Example 2: 1111-2222-3333 4444-5555-6666 B.
Scenario 2: SIM Injector in WAN of main Router and multiple Cellular Routers Setup topology In this scenario, each HD Dome creates a WAN connection to the main router. A single SIM Injector is used to provide SIM cards for each HD Dome. The HD Dome can be replaced with any Peplink cellular router supporting RemoteSIM technology. This scenario requires the completion of the configuration steps shown in Scenario 1 in addition to the configuration steps explained below.
1. Go to Network (Top tab), then Network Settings (Left-side tab), and click on Untagged LAN. This will open up the LAN settings page. 2. Change the IP address to 192.168.50.2. 3. In the DHCP Server section, uncheck the checkbox to disable DHCP Server. 4. Click Save and Apply Changes. Step 2. Ethernet port configuration The Ethernet port must be set to ACCESS mode for each HD Dome. To do this, dummy VLANs need to be created first. 1.
6. Click Save and Apply Changes. Configuration requirements for the main Router Requirements for the main router are: - Configure WAN 1 as a DHCP client. - WAN 1 will automatically get the Gateway IP address from HD Dome 1. - Configure WAN 2 as a Static IP and set it to 192.168.50.12. - Configure WAN 2 Gateway to 192.168.50.2. Same as the HD Dome 2’s IP address. https://www.peplink.
Scenario 3: SIM Injector in LAN of main Router and multiple Cellular Routers Setup topology In this scenario, SIMs are provided to the HD Domes via the main router. In this example, the Remote SIM Proxy functionality needs to be enabled on the main router. Notes: - HD Dome can be replaced with any other cellular router that supports RemoteSIM. - It is recommended to use Peplink Balance series or X series routers as the main router. https://www.peplink.
This scenario requires the completion of the configuration steps for the cellular router and the SIM Injector as in Scenario 1. The configuration for the main router is explained below. Main Router configuration IMPORTANT: Main router LAN side and Cellular Routers must be configured using different subnets, e.g. 192.168.50.1/24 and 192.168.100.1/24. Note: please make sure the Peplink router is running Firmware 8.1.0 or above. 1.
Scenario 4: SIM Injector in a remote location Setup topology Requirements for installing a SIM Injector in a remote location: ● ● ● ● Cellular router communicates with the SIM Injector via UDP port 50000. Therefore this port must be reachable via public IP over the Internet. The one way latency between the cellular router and the SIM Injector should be up to 250 ms. A higher latency may lead to stability issues. The cellular router must have Internet connection to connect to the SIM Injector.
2. Under Misc. settings (Left-side tab), find Remote SIM Management. 3. In Remote SIM Management, click on the edit icon next to Remote SIM is Disabled. 4. Enter the public IP of the SIM Injector and click Save and Apply Changes. Notes: - Do NOT check Auto LAN Discovery. Do NOT add a SIM Injector serial number to the Remote SIM Host field. Step 2. RemoteSIM and custom SIM card settings configurations are the same as in Scenario 1. https://www.peplink.
How to check if a Pepwave Cellular Router supports Remote SIM 1. Go to Network (Top tab), then WAN (Left-side tab), and click Details on any cellular WAN. This will open the WAN Connection Settings page. 2. Scroll down to Cellular settings. If you can see the Remote SIM Settings section, then the cellular router supports Remote SIMs. Monitor the status of the Remote SIM 1. Go to Network (Top tab), then WAN (Left-side tab), and click Details on the cellular WAN which was configured to use RemoteSIM. 2.
Appendix C: Overview of ports used by Peplink SD-WAN routers and other Peplink services Default Port Number Usage Service Inbound/Outbound Default Status UDP 5246 Data flow InControl Outbound Enabled TCP 443 HTTPS service InControl Outbound Enabled TCP 5246 Optional, used when TCP 443 is not responding InControl Outbound Enabled Outbound Enabled InControl Virtual Appliance TCP 5246 Remote Web Admin TCP 4500 VPN Data (TCP Mode) PepVPN / SpeedFusion Inbound / Outbound* Disabled TC
Interface access TCP 443 HTTPS traffic Web Admin Interface access (secure) TCP 8822 SSH SSH Inbound Disabled UDP 161 SNMP Get SNMP monitoring Inbound Disabled UDP 162 SNMP Trap SNMP monitoring Outbound Disabled TCP, UDP 1812 Radius Authentication Radius Outbound Disabled TCP, UDP 1813 Radius Accounting Radius Outbound Disabled UDP 123 Network Time Protocol NTP Inbound Outbound Disabled Enabled TCP 60660 Real-time location data in NMEA format GPS Outbound Disabled Inboun
Appendix D: Declaration FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX BR1 Mini This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
CE Statement for Pepwave Routers ( MAX BR1 Mini for EC25-E) https://www.peplink.
https://www.peplink.
2.4GHz ( 2412 – 2472 MHz ) : 16.38 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
CE Statement for Pepwave Routers ( MAX BR1 Mini for MC7455) https://www.peplink.
https://www.peplink.
2.4GHz ( 2412 – 2472 MHz ) : 16.38 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
Industry Canada Statement (for MAX BR1 Mini) This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
FCC & IC Requirements for Operation in the United States and Canada (for MAX BR1 Mini) FCC ID : U8G-P1930LITER6 FCC 15.21: The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Informations concernant l'exposition aux frequences radio (RF) Cet equipement est conforme avec l'exposition aux radiations IC definies pour un environnement noncontrole. Cet equipement doit etre installe et utilise a une distance minimum de 20 cm entre le radiateuret votre corps. Cet emetteur ne doit pas etre co-localisees ou operant en conjonction avec une autreantenne ou transmetteur.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX BR1 MK2 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
exempts de licence.
CE Statement for Pepwave Routers ( MAX BR1 MK2 ) https://www.peplink.
https://www.peplink.
2.4GHz ( 2412 – 2472 MHz ) : 19.95 dBm 5GHz ( 5150 - 5250 MHz ) : 22.73 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX BR1 Classic This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Industry Canada Statement ( for MAX BR1 Classic ) This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions (1) This device may not cause interference; and(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
CE Statement for Pepwave Routers ( MAX BR1 Classic for MC7455) https://www.peplink.
https://www.peplink.
2.4GHz ( 2412 – 2472 MHz ) : 19.78 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
CE Statement for Pepwave Routers ( MAX BR1 Classic for EC25-E) https://www.peplink.
https://www.peplink.
2.4GHz ( 2412 – 2472 MHz ) : 19.78 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX HD4 MBX, MAX HD2 MBX, MAX HD4 MBX 5G, MAX HD2 MBX 5G This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Le présent produit est conforme aux spécifications techniques applicables d'Innovation, Sciences et Développement économique Canada. (i) The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p.
Battery Caution Statement (MAX HD4 MBX, MAX HD2 MBX, MAX HD4 MBX 5G, MAX HD2 MBX 5G) Risk of explosion if the battery replaced by an incorrect type, place the battery into fire, a hot oven, extremely high temperature or low air pressure surrounding environment, the leakage of flammable liquid or gas, and mechanically crushing or cutting of the battery. https://www.peplink.
CE Statement for Pepwave Routers ( MAX HD4 MBX For EM7565 ) https://www.peplink.
https://www.peplink.
2.4GHz ( 2412 – 2472 MHz ) : 19.6 dBm 5GHz ( 5150 - 5250 MHz ) : 19.4 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
CE Statement for Pepwave Routers ( MAX HD2 MBX / MAX HD4 MBX For LM960A18) https://www.peplink.
https://www.peplink.
2.4GHz ( 2412 – 2472 MHz ) : 19.6 dBm 5GHz ( 5150 - 5250 MHz ) : 19.4 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
CE Statement for Pepwave Routers (MAX HD2 MBX 5G / MAX HD4 MBX 5G For MV31-W) https://www.peplink.
https://www.peplink.
2.4GHz ( 2412 – 2472 MHz ) : 19.6 dBm 5GHz ( 5150 - 5250 MHz ) : 19.4 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX HD2 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
(i) The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and The high-power radars are allocated as primary users (i.e.
https://www.peplink.
CE Statement for Pepwave Routers ( MAX HD2 For MC7455) https://www.peplink.
https://www.peplink.
2.4GHz ( 2412 – 2472 MHz ) : 19.90 dBm 5GHz ( 5150 - 5250 MHz ) : 22.88 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
CE Statement for Pepwave Routers ( MAX HD2 For MC7565) https://www.peplink.
https://www.peplink.
2.4GHz ( 2412 – 2472 MHz ) : 19.86 dBm 5GHz ( 5150 - 5250 MHz ) : 22.68 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
Mounting the Unit Wall Mount Some devices can be wall mounted using screws. After adding the screw on the wall, slide in the screw hole socket as indicated below. Recommended screw specification M3.5 x 20mm, head diameter 6mm, head thickness 2.4mm. For type 1, the device requires four screws for wall mounting. For type 2, the device requires two screws for wall mounting. https://www.peplink.
( For MAX BR1 Classic CB IEC 62368-1 ) Output of the external power source shall complied with ES1 and ES2 requirements, output rating 10-30 Vdc, minimum 12W ( DC Jack or POE injector ), with minimum ambient temperature 65 ℃, altitude = 5000m , and evaluated in accordance to UL/EN/IEC 60950-1 and / or UL/EN/IEC 62368-1 Ensure to connect the power cord of power adapter to a socket-outlet with earthing.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX BR1 Pro 5G FCC 15.21 The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Industry Canada Statement ( MAX BR1 Pro 5G ) This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
antenna gain for 5GHz ( 5150 ~ 5250 MHz ) 4.10 dBi antenna gain for 5GHz ( 5725 ~ 5850 MHz ) 4.73 dBi Battery Caution Statement Risk of explosion if the battery replaced by an incorrect type, place the battery into fire, a hot oven, extremely high temperature or low air pressure surrounding environment, the leakage of flammable liquid or gas, and mechanically crushing or cutting of the battery. https://www.peplink.
CE Statement for Pepwave Routers ( MAX BR1 Pro 5G) https://www.peplink.
https://www.peplink.
2.4GHz ( 2412 – 2472 MHz ) : 19.74 dBm 5GHz ( 5150 - 5250 MHz ) : 22.66 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
CE Statement for Pepwave Routers ( MAX BR1 Pro LTEA for EM7690) https://www.peplink.
https://www.peplink.
2.4GHz ( 2412 – 2472 MHz ) : 19.74 dBm 5GHz ( 5150 - 5250 MHz ) : 22.66 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX BR1 Mini Core This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d’en Radiation Exposure Statement This device complies with the ISED radiation exposure limit set forth for an uncontrolled environment.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX BR1 Mini HW3 (FCC ID: U8G-P1MT01) Federal Communication Commission Interference Statement Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
CE Statement for Pepwave Routers ( MAX BR1 Mini HW3 for EC25-E & LN920A6-WW ) https://www.peplink.
https://www.peplink.
2.4GHz ( 2412 - 2472 MHz ) : 19.95 dBm 5GHz ( 5150 - 5250 MHz ) : 22.65 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) EC25-E module: LN920A6-WW module: This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX 700 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
For MAX HD2 IP67, MAX HD2 Mini, MAX HD2 Dome, MAX HD4 IP67, MAX BR1 ENT, MAX BR1 M2M, SpeedFusion Engine Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d’en Radiation Exposure Statement This device complies with the ISED radiation exposure limit set forth for an uncontrolled environment.
CE Statement for Pepwave Routers ( MAX HD2 IP67 ) https://www.peplink.
https://www.peplink.
WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
CE Statement for Pepwave Routers ( MAX HD1 Dome ) https://www.peplink.
https://www.peplink.
WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
CE Statement for Pepwave Routers ( MAX HD2 Dome ) https://www.peplink.
https://www.peplink.
WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
CE Statement for Pepwave Routers ( MAX BR1 ESN ) https://www.peplink.
https://www.peplink.
2.4GHz ( 2412 - 2472 MHz ) : 19.78 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX HD4 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en (i) The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complie
CE Statement for Pepwave Routers ( MAX HD4 ) https://www.peplink.
https://www.peplink.
2.4GHz ( 2412 - 2472 MHz ) : 18.87 dBm 5GHz ( 5150 - 5250 MHz & 5725 - 5850 MHz ) : 19.13 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
CE Statement for Pepwave Routers ( MAX HD4 IP67 ) https://www.peplink.
https://www.peplink.
WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
CE Statement for Pepwave Routers ( SpeedFusion Engine ) https://www.peplink.
https://www.peplink.
WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) MC7455 module: EC25-E module: This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX Transit, MAX Transit Duo Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio ex- empts de licence.
CE Statement for Pepwave Routers ( MAX Transit / MAX Transit Duo For EM7565 ) https://www.peplink.
https://www.peplink.
2.4GHz ( 2412 - 2472 MHz ) : 18.68 dBm 5GHz ( 5150 - 5250 MHz ) : 18.19 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
CE Statement for Pepwave Routers ( MAX Transit For LM960A18 )
2.4GHz ( 2412 - 2472 MHz ) : 18.68 dBm 5GHz ( 5150 - 5250 MHz ) : 18.19 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX Transit Mini Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This radio transmitter has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Antenna types Replacement Antenna Antenna gain (in dBi) 5.
CE Statement for Pepwave Routers ( MAX Transit Mini )
2.4GHz ( 2412 - 2472 MHz ) : 19.78 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator & your body. contact as: https://www.peplink.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX BR1 PRO, UBR LTE Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
For licence exempt equipment with detachable antennas, the user manual shall also contain the following notice in a conspicuous location: This radio transmitter 20682-P1941 has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Radiation Exposure Statement This device complies with the ISED radiation exposure limit set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 23 cm between the radiator & your body. Cet equipement est conforme avec l'exposition aux radiations ISED definies pour un environnement non controle. Cet equipement doit etre installe et utilise a une distance minimum de 23 cm entre le radiateur et votre corps.
CE Statement for Pepwave Routers ( MAX BR1 PRO / UBR LTE )
2.4GHz ( 2412 - 2472 MHz ) : 19.94 dBm 5GHz ( 5150 - 5250 MHz ) : 20.34 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX BR1 IP55, MAX BR2 IP55 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
CE Statement for Pepwave Routers ( MAX BR1 IP55 )
2.4GHz ( 2412 - 2472 MHz ) : 18.16 dBm 5GHz ( 5150 - 5250 MHz) : 20.32 dBm 5GHz ( 5725 - 5850 MHz) : 13.00 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 50cm between the radiator & your body. contact as: https://www.peplink.
CE Statement for Pepwave Routers ( MAX BR2 IP55 )
2.4GHz ( 2412 - 2472 MHz ) : 18.99 dBm 5GHz ( 5150 - 5250 MHz ) : 22.95 dBm 5GHz ( 5725 - 5850 MHz ) : 12.80 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 50cm between the radiator & your body. contact as: https://www.peplink.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX Transit Pro E / MAX Transit LTEA (FCC ID: U8G-P1835) FCC 15.21: Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. FCC 15.105 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
ICES Statement This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. Le présent produit est conforme aux spécifications techniques applicables d'Innovation, Sciences et Développement économique Canada. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1.
This radio transmitter IC: 20682-P1835 has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Cet émetteur radio IC : 20682-P1835 a été approuvé par Innovation, Sciences et Développement économique Canada doit fonctionner avec les types d'antennes énumérés ci-dessous, avec le gain maximal admissible indiqué. Les types d'antenne non inclus dans cette liste qui ont un gain supérieur au gain maximum indiqué pour tout type répertorié sont strictement interdits pour une utilisation avec cet appareil.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX Transit Pro E (FCC ID: U8G-P1AX09) Federal Communication Commission Interference Statement Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio ex-empts de licence.
point à point et non point à point. Radiation Exposure Statement This equipment complies with ISED RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. Cet appareil doit être installé et utilisé avec une distance minimale de 20cm entre l’émetteuret votre corps.
CE Statement for Pepwave Routers ( MAX Transit Pro E for LN920A12-WW)
2.4GHz ( 2412 - 2472 MHz ) : 19.97 dBm 5GHz ( 5150 - 5250 MHz ) : 22.99 dBm LN920A12-WW: WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX Transit Pro Federal Communication Commission Interference Statement Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
CE Statement for Pepwave Routers ( MAX Transit Pro for EM7421 & EM12-G )
2.4GHz ( 2412 - 2472 MHz ) : 19.74 dBm 5GHz ( 5150 - 5250 MHz ) : 22.88 dBm EM7421: WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) EM12-G: WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
CE Statement for Pepwave Routers ( MAX BR2 Pro )
2.4GHz ( 2412 - 2472 MHz ) : 19.94 dBm 5GHz ( 5150 - 5250 MHz ) : 22.96 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
CE Statement for Pepwave Routers ( UBR Plus )
2.4GHz ( 2412 - 2472 MHz ) : 19.84 dBm 5GHz ( 5150 - 5250 MHz ) : 22.76 dBm WWAN : Refer 3GPP TS 36.521 -1 ( UE Power class ) This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For MAX BR2 Pro (FCC ID: U8G-P1AX203) Federal Communication Commission Interference Statement Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
(i) The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potent for harmful interference to co-channel mobile satellite systems; (ii) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate; (detachable antenna only) ; and The high-power radars are allocated as primary users (i.e.
This radio transmitter IC: 20682-P1AX203 has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. WIFI Antenna type: Omni-directional WIFI Antenna gain: 2.4GHz / 2.44 dBi 5150 ~ 5250 MHz / 4.1 dBi 5725 ~ 5850 MHz / 4.
USB WAN Modem Port Specification MAX Series Output Rating MAX 700 MAX HD2 / MAX HD2 Media Fast MAX HD2 Mini MAX HD2 / HD4 MBX MAX BR1 ENT MAX HD4 / MAX HD4 Media Fast / MediaFast 200 MAX BR2 Pro 5V DC, 2A 5V DC, 2A 5V DC, 2A 5V DC, 0.
