Pepwave MAX and Surf User Manual IPsec VPN Settings Name This field is for specifying a local name to represent this connection profile. Active When this box is checked, this IPsec VPN connection profile will be enabled. Otherwise, it will be disabled. Connect Upon Disconnection of Check this box and select a WAN to connect to this VPN automatically when the specified WAN is disconnected.
Pepwave MAX and Surf User Manual Authentication Mode Force UDP Encapsulation To access your VPN, clients will need to authenticate by your choice of methods. Choose between the Preshared Key and X.509 Certificate methods of authentication. Choose Main Mode if both IPsec peers use static IP addresses. Choose Aggressive Mode if one of the IPsec peers uses dynamic IP addresses. For forced UDP encapsulation regardless of NAT-traversal, tick this checkbox.
Pepwave MAX and Surf User Manual WAN Connection Priority WAN Connection Select the appropriate WAN connection from the drop-down menu. http://www.pepwave.
Pepwave MAX and Surf User Manual 14 Outbound Policy Management Pepwave routers can flexibly manage and load balance outbound traffic among WAN connections. Important Note Outbound policy is applied only when more than one WAN connection is active. The settings for managing and load balancing outbound traffic are located at Advanced>Outbound Policy or Advanced>PepVPN, depending on the model. 14.
Pepwave MAX and Surf User Manual Application Compatibility highest application compatibility. Normal Application Compatibility Outbound traffic from a source LAN device to the same destination Internet IP address will be routed through the same WAN connection persistently, regardless of protocol. This option provides high compatibility to most applications, and users still benefit from WAN link load balancing when multiple Internet servers are accessed.
Pepwave MAX and Surf User Manual The bottom-most rule is Default (GLW WKLV UXOH WR FKDQJH WKH GHYLFH¶V GHIDXOW PDQQHU RI controlling outbound traffic for all connections that do not match any of the rules above it. Under the Service heading, click Default to change these settings. To rearrange the priority of outbound rules, drag and drop them into the desired sequence. By default, Auto is selected as the Default Rule. You can select Custom to change the algorithm to be used.
Pepwave MAX and Surf User Manual New Custom Rule Settings Service Name This setting specifies the name of the outbound traffic rule. Enable This setting specifies whether the outbound traffic rule takes effect. When Enable is checked, the rule takes effect: traffic is matched and actions are taken by the Pepwave router based on the other parameters of the rule. When Enable is unchecked, the rule does not take effect: the Pepwave router disregards the other parameters of the rule.
Pepwave MAX and Surf User Manual This setting specifies the behavior of the Pepwave router for the custom rule. One of the following values can be selected (note that some Pepwave routers provide only some of these options): y Weighted Balance Algorithm y Persistence y Enforced y Priority y Overflow y Least Used y Lowest Latency The upcoming sections detail the listed algorithms.
Pepwave MAX and Surf User Manual 14.2.1 Algorithm: Weighted Balance This setting specifies the ratio of WAN connection usage to be applied on the specified IP protocol and port. This setting is applicable only when Algorithm is set to Weighted Balance. The amount of matching traffic that is distributed to a WAN connection is proportional to the weight of the WAN connection relative to the total weight.
Pepwave MAX and Surf User Manual 14.2.2 Algorithm: Persistence The configuration of persistent services is the solution to the few situations where link load distribution for Internet services is undesirable. For example, for security reasons, many e-banking and other secure websites terminate the session when the client FRPSXWHU¶V ,QWHUQHW ,3 DGGUHVV FKDQJHV PLG-session. In general, different Internet IP addresses represent different computers.
Pepwave MAX and Surf User Manual 14.2.3 Algorithm: Enforced This setting specifies the WAN connection usage to be applied on the specified IP protocol and port. This setting is applicable only when Algorithm is set to Enforced. Matching traffic will be routed through the specified WAN connection, regardless of the health check status of the WAN connection. Starting from Firmware 5.2, outbound traffic can be enforced to go through a specified SpeedFusionTM connection. 14.2.
Pepwave MAX and Surf User Manual Drag and drop to specify the order of WAN connections to be used for routing traffic. Only the highest priority healthy connection that is not in full load will be used. 14.2.6 Algorithm: Least Used The traffic matching this rule will be routed through the healthy WAN connection that is selected in Connection and has the most available download bandwidth.
Pepwave MAX and Surf User Manual available bandwidth. 14.2.8 Expert Mode Expert Mode is available on some Pepwave routers for use by advanced users. To enable the feature, click on the help icon and click turn on Expert Mode. In Expert Mode, a new special rule, SpeedFusionTM Routes, is displayed in the Custom Rules table. This rule represents all SpeedFusionTM routes learned from remote VPN peers. By default, this bar is on the top of all custom rules.
Pepwave MAX and Surf User Manual 15 Inbound Access 15.1 Port Forwarding Service Pepwave routers can act as a firewall that blocks, by default, all inbound access from the Internet. By using port forwarding, Internet users can access servers behind the Pepwave router. Inbound port forwarding rules can be defined at Advanced>Port Forwarding. To define a new service, click Add Service. Port Forwarding Settings Enable This setting specifies whether the inbound service takes effect.
Pepwave MAX and Surf User Manual The Port setting specifies the port(s) that correspond to the service, and can be configured to behave in one of the following manners: Any Port, Single Port, Port Range, Port Map, and Range Mapping Any Port: all traffic that is received by the Pepwave router via the specified protocol is forwarded to the servers specified by the Servers setting. For example, with IP Protocol set to TCP, and Port set to Any Port, all TCP traffic is forwarded to the configured servers.
Pepwave MAX and Surf User Manual 15.1.1 UPnP / NAT-PMP Settings UPnP and NAT-PMP are network protocols which allow a computer connected to the LAN port to automatically configure the router to allow parties on the WAN port to connect to itself. That way, the process of inbound port forwarding becomes automated. When a computer creates a rule using these protocols, the specified TCP/UDP port of all WAN connections' default IP address will be forwarded.
Pepwave MAX and Surf User Manual 16 NAT Mappings NAT mappings allow IP address mapping of all inbound DQG RXWERXQG 1$7¶dt raffic to and from an internal client IP address. Settings to configure NAT mappings are located at Advanced>NAT Mappings. To add a rule for NAT mappings, click Add NAT Rule. NAT Mapping Settings LAN Client(s) NAT mapping rules can be defined for a single LAN IP Address, an IP Range, or an IP Network. Address 7KLV UHIHUV WR WKH /$1 KRVW¶V SULYDWH ,3 DGGUHVV 7KH V\VWHP PDSV WKLV DGG
Pepwave MAX and Surf User Manual Inbound Mappings This setting specifies the WAN connections and corresponding WAN-specific Internet IP addresses on which the system should bind. Any access to the specified WAN connection(s) and IP address(es) will be forwarded to the LAN host. This option is only available when IP Address is selected in the LAN Client(s) field. Note that inbound mapping is not needed for WAN connections in drop-in mode or IP forwarding mode.
Pepwave MAX and Surf User Manual 17 QoS 17.1 User Groups LAN and PPTP clients can be categorized into three user groups: Manager, Staff, and Guest. This menu allows you to define rules and assign client IP addresses or subnets to a user group. You can apply different bandwidth and traffic prioritization policies on each user group in the Bandwidth Control and Application sections (note that the options available here vary by model). The table is automatically sorted by rule precedence.
Pepwave MAX and Surf User Manual 17.2 Bandwidth Control You can define a maximum download speed (over all WAN connections) and upload speed (for each WAN connection) that each individual Staff and Guest member can consume. No limit can be imposed on individual Manager members. By default, download and upload bandwidth limits are set to unlimited (set as 0). 17.3 Application 17.3.
Pepwave MAX and Surf User Manual 17.3.2 Prioritization for Custom Applications Click the Add button to define a custom application. Click the button column to delete the custom application in the corresponding row. in the Action When Supported Applications is selected, the Pepwave router will inspect network traffic and prioritize the selected applications. Alternatively, you can select Custom Applications and define the application by providing the protocol, scope, port number, and DSCP value. 17.3.
Pepwave MAX and Surf User Manual 18 Firewall A firewall is a mechanism that selectively filters data traffic between the WAN side (the Internet) and the LAN side of the network. It can protect the local network from potential hacker attacks, access to offensive websites, and/or other inappropriate uses.
Pepwave MAX and Surf User Manual Click Add Rule to display the following screen: Inbound firewall settings are located at Advanced>Firewall>Access Rules>Inbound Firewall Rules. Click Add Rule to display the following screen: Rules are matched from top to bottom. If a connection matches any one of the upper rules, the matching process will stop. If none of the rules match, the Default rule will be applied. By default, the Default rule is set as Allow for both outbound and inbound access. http://www.
Pepwave MAX and Surf User Manual Inbound / Outbound Firewall Settings Rule Name Enable WAN Connection (Inbound) This setting specifies a name for the firewall rule. This setting specifies whether the firewall rule should take effect. If the box is checked, the firewall rule takes effect. If the traffic matches the specified protocol/IP/port, actions will be taken by the Pepwave router based on the other parameters of the rule. If the box is not checked, the firewall rule does not take effect.
Pepwave MAX and Surf User Manual Aug 13 23:47:44 Denied CONN=Ethernet WAN SRC=20.3.2.1 DST=192.168.1.20 LEN=48 PROTO=TCP SPT=2260 DPT=80 x CONN: The connection where the log entry refers to x SRC: Source IP address x DST: Destination IP address x LEN: Packet length x PROTO: Protocol x SPT: Source port x DPT: Destination port Click Save to store your changes. To create an additional firewall rule, click Add Rule and repeat the above steps. 7R FKDQJH D UXOH¶V SULRULW\ VLPSO\ GUDJ DQG GURS WKH r
Pepwave MAX and Surf User Manual 18.1.2 Apply Firewall Rules to PepVpn Traffic When this option is enabled, Outbound Firewall Rules will be applied to PepVPN traffic. To turn on this feature, click , check the Enable check box, and press the Save button. 18.1.3 Intrusion Detection and DoS Prevention Pepwave routers can detect and prevent intrusions and denial-of-service (DoS) attacks from the Internet. To turn on this feature, click , check the Enable check box, and press the Save button.
Pepwave MAX and Surf User Manual 18.2 Web Blocking 18.2.1 Web Blocking Enter an appropriate website address, and the Pepwave router will block and disallow LAN/PPTP/SpeedFusionTM peer clients to access these websites. Exceptions can be added using the instructions in Sections 18.2.2 and 18.2.3. You may enter a wildcard ".*" at the end of a domain name to block any web site with a host name having the domain name in the middle. For example, If you enter foobar.*, www.foobar.com, www.foobar.co.
Pepwave MAX and Surf User Manual OSPF Router ID Area This field determines the ID of the router. By default, this is specified as the LAN IP address. If you want to specify your own ID, enter it in the Custom field. This is an overview of the OSPFv2 areas you have defined. Click on the area name to configure it. To set a new area, click Add. To delete an existing area, click . OSPF Settings Area ID Link Type Authentication Interfaces Determine the name of your Area ID to apply to this group.
Pepwave MAX and Surf User Manual To access RIPv2 settings, click . RIPv2 Settings Authentication Interfaces Choose an authentication method, if one is used, from this drop-down menu. Available options are MD5 and Text. Enter the authentication key next to the drop-down menu. Determine which interfaces this group will use to listen to and deliver RIPv2 packets. 18.4 Remote User Access a Networks routed by a Peplink Balance can be remotely accessed via L2TP with IPsec or PPTP.
Pepwave MAX and Surf User Manual Remote User Access Settings Enable Click the checkbox to enable Remote User Access. VPN Type Determine whether remote devices can connect to the Balance using L2TP with IPsec or PPTP. For greater security, we recommend you connect using L2TP with IPsec. Preshared Key Enter your preshared key in the text field. Please note that remote devices will need this preshared key to access the Balance.
Pepwave MAX and Surf User Manual Miscellaneous Settings The miscellaneous settings include configuration for high availability, PPTP server, service forwarding, and service passthrough. 18.5 High Availability Many Pepwave routers support high availability (HA) configurations via an open standard virtual router redundancy protocol (VRRP, RFC 3768). In an HA configuration, two Pepwave routers provide redundancy and failover in a master-slave arrangement.
Pepwave MAX and Surf User Manual You can configure high availability at Advanced>Misc. Settings>High Availability. Interface for Slave Router Interface for Master Router High Availability Enable Checking this box specifies that the Pepwave router is part of a high availability configuration. Group Number This number identifies a pair of Pepwave routers operating in a high availability configuration. The two Pepwave routers in the pair must have the same Group Number value.
Pepwave MAX and Surf User Manual Important Note For Pepwave routers in NAT mode, the virtual IP (VIP) should be set as the default gateway for all hosts on the LAN segment. For example, a firewall sitting behind the Pepwave router should set its default gateway as the virtual IP instead of the IP of the master router. In drop-in mode, no other configuration needs to be set. Please note that the drop-in WAN cannot be configured as a LAN bypass port while it is configured for high availability. http://www.
Pepwave MAX and Surf User Manual 18.6 PPTP Server Pepwave routers feature a built-in PPTP server, which enables remote computers to conveniently and securely access the local network. PPTP server settings are located at Advanced>Misc. Settings>PPTP Server. Check the box to enable PPTP server functionality. All connected PPTP sessions are displayed at Status>Client List. Please refer to Section 21.3 for details. Note that available options vary by model. http://www.pepwave.
Pepwave MAX and Surf User Manual PPTP Server Settings Listen On This setting is for specifying the WAN connection(s) and IP address(es) that the PPTP server should listen on. Authentication This setting is for specifying the user database source for PPTP authentication. Three sources can be selected: Local User Accounts, LDAP Server, or RADIUS Server. Local User Accounts - User accounts are stored in the Pepwave router locally. You can add/modify/delete accounts in the User Accounts table.
Pepwave MAX and Surf User Manual after selecting Enable. Web Proxy Forwarding When this option is enabled, all outgoing connections destined for the proxy server specified in Web Proxy Interception Settings will be intercepted. These connections will be redirected to a specified web proxy server and port number. Web proxy interception settings and proxy server settings for each WAN can be specified after selecting Enable.
Pepwave MAX and Surf User Manual 18.8.2 Web Proxy Forwarding When this feature is enabled, the Pepwave router will intercept all outgoing connections destined for the proxy server specified in Web Proxy Interception Settings, choose a WAN connection with reference to the outbound policy, and then forward them to the specified web proxy server and port number. Redirected server settings for each WAN can be set here. If forwarding is disabled for a WAN, web proxy connections for the :$1 ZLOO EH VLPSO\ IRUZD
Pepwave MAX and Surf User Manual 18.9 Service Passthrough Service passthrough settings can be found at Advanced>Misc. Settings>Service Passthrough. Some Internet services need to be specially handled in a multi-WAN environment. Pepwave routers can handle these services such that Internet applications do not notice being behind a multi-WAN router. Settings for service passthrough support are available here. Service Passthrough Support SIP Session initiation protocol, aka SIP, is a voice-over-IP protocol.
Pepwave MAX and Surf User Manual site VPN traffic, check Route IPsec Site-to-Site VPN and choose the WAN connection to route the traffic to. 18.10 GPS Forwarding Using the GPS forwarding feature, some Pepwave routers can automatically send GPS reports to a specified server. To set up GPS forwarding, navigate to Advanced>GPS Forwarding. GPS Forwarding Enable Check this box to turn on GPS forwarding. Server Enter the name/IP address of the server that will receive GPS data.
Pepwave MAX and Surf User Manual 19 AP Controller The AP controller acts as a centralized controller of Pepwave AP devices. With this feature, users can customize and manage multiple APs from a single Pepwave router interface. Special Note Each Pepwave router can control a limited number of routers without additional cost. To manage more, a Full Edition license is required. Please contact your Authorized Reseller or the Peplink Sales Team for more information and pricing details.
Pepwave MAX and Surf User Manual Current SSID information appears in the SSID section. To edit an existing SSID, click its name in the list. To add a new SSID, click Add. Note that the following settings vary by model. SSID Settings SSID Enable This setting specifies the SSID of the virtual AP to be scanned by Wi-Fi clients. Select Yes to enable the virtual AP. VLAN ID This setting specifies the VLAN ID to be tagged on all outgoing packets generated from this wireless network (i.e.
Pepwave MAX and Surf User Manual options and values available here. IGMP Snooping A To allow the Pepwave router to listen to internet group management protocol (IGMP) network traffic, select this option. DHCP Option 82 A If you use a distributed DHCP server/relay environment, you can enable this option to provide additional information on the manner in which clients are physically connected to the network.
Pepwave MAX and Surf User Manual When WPA/WPA2- Personal is configured, a shared key is used for data encryption and authentication. When using this configuration, the Shared Key option should be enabled. Key length must be between eight and 63 characters (inclusive). The security level of this method is known to be high. The configuration of Static WEP parameters enables pre-shared WEP key encryption. Authentication is not supported by this method. The security level of this method is known to be weak.
Pepwave MAX and Surf User Manual 19.2 Settings On many Pepwave models, the AP settings screen (AP>Settings) looks similar to the example below: AP Settings SSID These buttons specify which wireless networks will use this AP profile. You can also select the frequencies at which each network will transmit. Please note that the Pepwave router does not detect whether the AP is capable of transmitting at both frequencies. Instructions to transmit at unsupported frequencies will be ignored by the AP.
Pepwave MAX and Surf User Manual 5 GHz Channel This drop-down menu selects the 5 GHz 802.11 channel to be utilized. If Auto is set, the system will perform channel scanning based on the scheduled time set and choose the most suitable channel automatically. 2.4 GHz Protocol This section displays the 2.4GHz protocols your APs are using. 2.4 GHz Channel Bonding There are three options: 20 MHz, 20/40 MHz, and 40 MHz. With this feature enabled, the Wi-Fi system can use two channels at once.
Pepwave MAX and Surf User Manual Web Administration Settings Enable Check the box to allow the Pepwave router to manage the web admin access information of the AP. Web Access Protocol These buttons specify the web access protocol used for accessing the web admin of the AP. The two available options are HTTP and HTTPS. Management Port This field specifies the management port used for accessing the device.
Pepwave MAX and Surf User Manual Navigating to AP>Settings on some Pepwave models displays a screen similar to the one shown below: Wi-Fi Radio Settings Operating Country Wi-Fi Antenna This option sets the country whose regulations the Pepwave router follows. Choose from the router's internal or optional external antennas, if so equipped. Important Note Per FCC regulations, the country selection is not available on all models marketed in the US. All US models are fixed to US channels only.
Pepwave MAX and Surf User Manual selected. Beacon IntervalA DTIMA Slot TimeA This field allows you to set the frequency for the beacon to include a delivery traffic indication message. The interval is measured in milliseconds. The default value is set to 1 ms. This field is for specifying the wait time before the Surf SOHO transmits a packet. By default, this field is set to 9 µs.
Pepwave MAX and Surf User Manual 20 System Settings 20.1 Admin Security There are two types of user accounts available for accessing the web admin: admin and user. They represent two user levels: the admin level has full administration access, while the user level is read-only. The user level can access only the device's status information; users cannot make any changes on the device.
Pepwave MAX and Surf User Manual Admin Settings Router Name Admin User Name Admin Password This field allows you to define a name for this Pepwave router. By default, Router Name is set as MAX_XXXX or Surf_SOHO_XXXX, where XXXX refers to the last 4 digits of the XQLW¶V serial number. Admin User Name is set as admin by default, but can be changed, if desired. This field allows you to specify a new administrator password.
Pepwave MAX and Surf User Manual Authentication by RADIUS With this box is checked, the web admin will authenticate using an external RADIUS server. Authenticated users are treated as either "admin" with full read-write permission RU ³XVHU´ ZLWK UHDG-only access. Local admin and user accounts will be disabled. When the device is not able to communicate with the external RADIUS server, local accounts will be enabled again for emergency access.
Pepwave MAX and Surf User Manual WAN Connection Access Settings This field allows you to restrict web admin access only from defined IP subnets. x x Allowed Source IP Subnets Allow access from the following IP subnets only - Restrict web admin access only from the defined IP subnets. When this is chosen, a text input area will be displayed beneath: The allowed IP subnet addresses should be entered into this text area. Each IP subnet must be in form of w.x.y.z/m, where w.x.y.z is an IP address (e.g.
Pepwave MAX and Surf User Manual 20.2 Firmware Pepwave router firmware is upgradeable through the web admin interface. Firmware upgrade functionality is located at System>Firmware. There are two ways to upgrade the unit. The first method is through an online download. The second method is to upload a firmware file manually. To perform an online download, click on the Check for Firmware button. The Pepwave router will check online for new firmware.
Pepwave MAX and Surf User Manual 20.3 Time Time Settings enables the system clock of the Pepwave router to be synchronized with a specified time server. Time settings are located at System>Time. Time Settings Time Zone Time Server This specifies the time zone (along with the corresponding Daylight Savings Time scheme). The Time Zone value affects the time stamps in the 3HSZDYH URXWHU¶V event log and e-mail notifications. Check Show all to show all time zone options.
Pepwave MAX and Surf User Manual SMTP Server SSL Encryption This setting specifies the SMTP server to be used for sending email. If the server requires authentication, check Require authentication. Check the box to enable SMTPS. When the box is checked, SMTP Port will be changed to 465 automatically. SMTP Port This field is for specifying the SMTP port number. By default, this is set to 25; when SSL Encryption is checked, the default port number will be set to 465.
Pepwave MAX and Surf User Manual 20.5 Event Log Event log functionality enables event logging at a specified remote syslog server. The settings for configuring the remote system log can be found at System>Event Log. Event Log Settings Remote Syslog This setting specifies whether or not to log events at the specified remote syslog server. Remote Syslog Host This setting specifies the IP address or hostname of the remote syslog server.
Pepwave MAX and Surf User Manual 20.6 SNMP SNMP or simple network management protocol is an open standard that can be used to collect information about the Pepwave router. SNMP configuration is located at System>SNMP. SNMP Settings SNMP Device Name SNMP Port This field shows the router name defined at System>Admin Security. This option specifies the port which SNMP will use. The default port is 161. SNMPv1 This option allows you to enable SNMP version 1.
Pepwave MAX and Surf User Manual SNMP Community Settings Community Name Allowed Source Subnet Address This setting specifies the SNMP community name. This setting specifies a subnet from which access to the SNMP server is allowed. Enter subnet address here (e.g., 192.168.1.0) and select the appropriate subnet mask.
Pepwave MAX and Surf User Manual 20.7 InControl InControl is a cloud-based service which allows you to manage all of your Peplink and Pepwave devices with one unified system. With it, you can generate reports, gather statistics, and configure your devices automatically. All of this is now possible with InControl. When this check box is checked, the device's status information will be sent to the Peplink InControl system.
Pepwave MAX and Surf User Manual 20.8 Configuration Backing up Pepwave router settings immediately after successful completion of initial setup is strongly recommended. The functionality to download and upload Pepwave router settings is found at System>Configuration. Note that available options vary by model. Configuration Restore Configuration to Factory Settings The Restore Factory Settings button is to reset the configuration to factory default settings.
Pepwave MAX and Surf User Manual 20.9 Feature Add-ons Some Pepwave routers have features that can be activated upon purchase. Once the purchase is complete, you will receive an activation key. Enter the key in the Activation Key field, click Activate, and then click Apply Changes. 20.10 Reboot This page provides a reboot button for restarting the system. For maximum reliability, the Pepwave router can equip with two copies of firmware. Each copy can be a different version.
Pepwave MAX and Surf User Manual 20.11 Ping The ping test tool sends pings through a specified Ethernet interface or a SpeedFusionTM VPN connection. You can specify the number of pings in the field Number of times, to a maximum number of 10 times. Packet Size can be set to a maximum of 1472 bytes. The ping utility is located at System>Tools>Ping, illustrated below: Tip A system administrator can use the ping utility to manually check the connectivity of a particular LAN/WAN connection. http://www.
Pepwave MAX and Surf User Manual 20.12 Traceroute Test The traceroute test tool traces the routing path to the destination through a particular Ethernet interface or a SpeedFusionTM connection. The traceroute test utility is located at System>Tools>Traceroute. Tip A system administrator can use the traceroute utility to analyze the connection path of a LAN/WAN connection. 20.13 PepVPN Test The PepVPN Test tool can help to test the throughput between different VPN peers.
Pepwave MAX and Surf User Manual 20.14 CLI (Command Line Interface Support) The CLI (command line interface) can be accessed via SSH. This field enables CLI support. The below settings specify which TCP port and which interface(s) should accept remote SSH CLI access. The user name and password used for remote SSH CLI access are the same as those used for web admin access. http://www.pepwave.
Pepwave MAX and Surf User Manual 21 Status 21.1 Device System information is located at Status>Device. System Information Router Name Model Product Code Hardware Revision Serial Number Firmware This is the name specified in the Router Name field located at System>Admin Security. This shows the model name and number of this device. If your model uses a product code, it will appear here. This shows the hardware version of this device. This shows the serial number of this device.
Pepwave MAX and Surf User Manual Remote Assistance Click Turn on to enable remote assistance. The second table shows the MAC address of each LAN/WAN interface connected. To view your GHYLFH¶V (QG 8VHU /LFHQVH $JUHHPHQW (8/$ FOLFN . Important Note If you encounter issues and would like to contact the Pepwave Support Team (http://www.pepwave.com/contact/), please download the diagnostic report file and attach it along with a description of your issue. In Firmware 5.
Pepwave MAX and Surf User Manual 21.2 Active Sessions Information on active sessions can be found at Status>Active Sessions>Overview. This screen displays the number of sessions initiated by each application. Click on each service listing for additional information. This screen also indicates the number of sessions initiated by each WAN port. In addition, you can see which clients are initiating the most sessions. http://www.pepwave.
Pepwave MAX and Surf User Manual You can also perform a filtered search for specific sessions. You can filter by subnet, port, protocol, and interface. To perform a search, navigate to Status>Active Sessions>Search. This Active Sessions section displays the active inbound/outbound sessions of each WAN connection on the Pepwave router. A filter is available to sort active session information. Enter a keyword in the field or check one of the WAN connection boxes for filtering. http://www.pepwave.
Pepwave MAX and Surf User Manual 21.3 Client List The client list table is located at Status>Client List. It lists DHCP and online client IP addresses, names (retrieved from the DHCP reservation table or defined by users), current download and upload rate, and MAC address. Clients can be imported into the DHCP reservation table by clicking the button on the right. You can update the record after import by going to Network>LAN. If the PPTP server (see Section 19.2), SpeedFusionTM (see Section 12.
Pepwave MAX and Surf User Manual 21.5 UPnP / NAT-PMP The table that shows the forwarded ports under UPnP and NAT-PMP protocols is located at Status>UPnP/NAT-PMP. This section appears only if you have enabled UPnP / NAT-PMP as mentioned in Section 15.1.1. Click to delete a single UPnP / NAT-PMP record in its corresponding row. To delete all records, click Delete All on the right-hand side below the table.
Pepwave MAX and Surf User Manual Click the button for a chart displaying real-time throughput, latency, and droprate information for each WAN connection. When pressing the button, the following menu will appear: http://www.pepwave.
Pepwave MAX and Surf User Manual After clicking the icon, the following menu appears: Select the L2 protocol (TCP/UDP), direction, and duration and click the Start button to begin the general throughput test. http://www.pepwave.
Pepwave MAX and Surf User Manual The bandwidth bonding feature of PepVPN occurs when multiple WAN lines from one end merge with multiple WAN lines from the other end. For this to happen, each WAN line needs to form a connection with all the WAN lines on the opposite end. The function of the PepVPN analyzer is to report the throughput, packet loss, and latency of all possible combinations of connections.
Pepwave MAX and Surf User Manual 21.7 Event Log Event log information is located at Status>Event Log. The log section displays a list of events that has taken place on the Pepwave router. Check Auto Refresh to refresh log entries automatically. Click the Clear Log button to clear the log. 21.8 Bandwidth This section shows bandwidth usage statistics and is located at Status>Bandwidth. Bandwidth usage at the LAN while the device is switched off (e.g., LAN bypass) is neither recorded nor shown. http://www.
Pepwave MAX and Surf User Manual 21.8.1 Real-Time The Data transferred since installation table indicates how much network traffic has been processed by the device since the first bootup. The Data transferred since last reboot table indicates how much network traffic has been processed by the device since the last bootup. http://www.pepwave.
Pepwave MAX and Surf User Manual 21.8.2 Hourly This page shows the hourly bandwidth usage for all WAN connections, with the option of viewing each individual connection. Select the desired connection to check from the drop-down menu. 21.8.3 Daily http://www.pepwave.
Pepwave MAX and Surf User Manual This page shows the daily bandwidth usage for all WAN connections, with the option of viewing each individual connection. Select the connection to check from the drop-down menu. If you have enabled the Bandwidth Monitoring feature, the Current Billing Cycle table for that WAN connection will be displayed. Click on a date to view the client bandwidth usage of that specific date.
Pepwave MAX and Surf User Manual 21.8.4 Monthly This page shows the monthly bandwidth usage for each WAN connection. If you have enabled the Bandwidth Monitoring feature, you can check the usage of each particular connection and view the information by Billing Cycle or by Calendar Month. Click the first two rows to view the client bandwidth usage in the last two months. This feature is not available if you have chosen to view the bandwidth of an individual WAN connection.
Pepwave MAX and Surf User Manual Ethernet WAN Monthly Bandwidth Usage Tip By default, the scale of data size is in MB. 1GB equals 1024MB. http://www.pepwave.
Pepwave MAX and Surf User Manual Appendix A. Restoration of Factory Defaults To restore the factory default settings on a Pepwave router, follow the steps below: 1. Locate the reset button on the front or back panel of the Pepwave router. 2. With a paper clip, press the reset button and hold it for at least 10 seconds, until the unit reboots itself. After the Pepwave router finishes rebooting, the factory default settings will be restored.
Pepwave MAX and Surf User Manual Appendix B. Declaration 1. The device supports time division technology 2. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Pepwave MAX and Surf User Manual FCC Radiation Exposure Statement (for MAX On-The-Go) This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. 1. 20cm minimum when the product is operated alone without co-transmitting with a plug-in 3G USB dongle device. 2. 65cm minimum when the product is operated with a plug-in 3G USB device which has maximum of 7W ERP output power. 3.
Pepwave MAX and Surf User Manual requirements, covering essential requirements of article 3.2 of the R&TTE Directive - EN 301 511 V9.0.2: 2003 Global System for Mobile communications (GSM); Harmonized standard for mobile stations in the GSM 900 and DCS 1800 bands covering essential requirements under article 3.2 of the R&TTE directive (1999/5/EC) - EN 301 489-1 V1.9.
Pepwave MAX and Surf User Manual Español [Spanish] ǼȜȜȘȞȚțȒ [Greek] Français [French] Italiano [Italian] Latviski [Latvian] /LHWXYLǐ [Lithuanian] Nederlands [Dutch] Malti [Maltese] Magyar [Hungarian] Polski [Polish] Português [Portuguese] Slovensko [Slovenian] Slovensky [Slovak] Suomi [Finnish] Svenska [Swedish] compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Pepwave MAX and Surf User Manual http://www.pepwave.
Contact Us: Sales http://www.pepwave.com/contact/sales/ Support http://www.pepwave.com/contact/ Business Development and Partnerships http://www.pepwave.
