Pepwave MAX and Surf User Manual A web login session will be logged out automatically when it has been idle longer than the Web Session Timeout. Before the session expires, you may click the Logout button in the web admin to exit the session. 0 hours 0 minutes signifies an unlimited session time. This setting should be used only in special situations, as it will lower the system security level if users do not log out before closing the browser. The default is 4 hours, 0 minutes.
Pepwave MAX and Surf User Manual Admin Settings Router Name Admin User Name Admin Password This field allows you to define a name for this Pepwave router. By default, Router Name is set as MAX_XXXX or Surf_SOHO_XXXX, where XXXX refers to the last 4 digits of the unit’s serial number. Admin User Name is set as admin by default, but can be changed, if desired. This field allows you to specify a new administrator password.
Pepwave MAX and Surf User Manual support. For additional information regarding CLI, please refer to Section 21.16. CLI SSH Port CLI SSH Access This field determines the port on which clients can access CLI SSH. This menu allows you to choose between granting access to LAN and WAN clients, or to LAN clients only.
Pepwave MAX and Surf User Manual • • Allowed WAN IP Address(es) 192.168.0.0/24 10.8.0.0/16 This is to choose which WAN IP address(es) the web server should listen on. http://www.pepwave.
Pepwave MAX and Surf User Manual 21.2 Firmware Pepwave router firmware is upgradeable through the web admin interface. Firmware upgrade functionality is located at System>Firmware. There are two ways to upgrade the unit. The first method is through an online download. The second method is to upload a firmware file manually. To perform an online download, click on the Check for Firmware button. The Pepwave router will check online for new firmware.
Pepwave MAX and Surf User Manual 21.3 Time Time Settings enables the system clock of the Pepwave router to be synchronized with a specified time server. Time settings are located at System>Time. Time Settings Time Zone Time Server This specifies the time zone (along with the corresponding Daylight Savings Time scheme). The Time Zone value affects the time stamps in the Pepwave router’s event log and e-mail notifications. Check Show all to show all time zone options.
Pepwave MAX and Surf User Manual Edit Schedule Profile Enabling Name Click this checkbox to enable this schedule profile. Note that if this is disabled, then any associated features will also have their scheduling disabled. Enter your desired name for this particular schedule profile. Schedule Click the drop-down menu to choose pre-defined schedules as your starting point. Please note that upon selection, previous changes on the schedule map will be deleted.
Pepwave MAX and Surf User Manual Email Notification Settings Email Notification This setting specifies whether or not to enable email notification. If Enable is checked, the Pepwave router will send email messages to system administrators when the WAN status changes or when new firmware is available. If Enable is not checked, email notification is disabled and the Pepwave router will not send email messages. SMTP Server This setting specifies the SMTP server to be used for sending email.
Pepwave MAX and Surf User Manual clicked, you will see this screen to confirm the settings: Click Send Test Notification to confirm. In a few seconds, you will see a message with detailed test results. 21.6 Event Log Event log functionality enables event logging at a specified remote syslog server. The settings for configuring the remote system log can be found at System>Event Log. Event Log Settings Remote Syslog This setting specifies whether or not to log events at the specified remote syslog server.
Pepwave MAX and Surf User Manual The Pepwave router can also send push notifications to mobile devices that have our Mobile Router Utility installed. Check the box to activate this feature. Push Events For more information on the Router Utility, go to: www.peplink.com/products/router-utility http://www.pepwave.
Pepwave MAX and Surf User Manual 21.7 SNMP SNMP or simple network management protocol is an open standard that can be used to collect information about the Pepwave router. SNMP configuration is located at System>SNMP. SNMP Settings SNMP Device Name SNMP Port This field shows the router name defined at System>Admin Security. This option specifies the port which SNMP will use. The default port is 161. SNMPv1 This option allows you to enable SNMP version 1.
Pepwave MAX and Surf User Manual SNMP Community Settings Community Name Allowed Source Subnet Address This setting specifies the SNMP community name. This setting specifies a subnet from which access to the SNMP server is allowed. Enter subnet address here (e.g., 192.168.1.0) and select the appropriate subnet mask.
Pepwave MAX and Surf User Manual 21.8 InControl InControl is a cloud-based service which allows you to manage all of your Peplink and Pepwave devices with one unified system. With it, you can generate reports, gather statistics, and configure your devices automatically. All of this is now possible with InControl. When this check box is checked, the device's status information will be sent to the Peplink InControl system.
Pepwave MAX and Surf User Manual Backing up Pepwave router settings immediately after successful completion of initial setup is strongly recommended. The functionality to download and upload Pepwave router settings is found at System>Configuration. Note that available options vary by model. Configuration Restore Configuration to Factory Settings The Restore Factory Settings button is to reset the configuration to factory default settings.
Pepwave MAX and Surf User Manual 21.10 Feature Add-ons Some Pepwave routers have features that can be activated upon purchase. Once the purchase is complete, you will receive an activation key. Enter the key in the Activation Key field, click Activate, and then click Apply Changes. 21.11 Reboot This page provides a reboot button for restarting the system. For maximum reliability, the Pepwave router can equip with two copies of firmware. Each copy can be a different version.
Pepwave MAX and Surf User Manual 21.12 Ping The ping test tool sends pings through a specified Ethernet interface or a SpeedFusionTM VPN connection. You can specify the number of pings in the field Number of times, to a maximum number of 10 times. Packet Size can be set to a maximum of 1472 bytes. The ping utility is located at System>Tools>Ping, illustrated below: Tip A system administrator can use the ping utility to manually check the connectivity of a particular LAN/WAN connection. http://www.pepwave.
Pepwave MAX and Surf User Manual 21.13 Traceroute Test The traceroute test tool traces the routing path to the destination through a particular Ethernet interface or a SpeedFusionTM connection. The traceroute test utility is located at System>Tools>Traceroute. Tip A system administrator can use the traceroute utility to analyze the connection path of a LAN/WAN connection. 21.14 PepVPN Test The PepVPN Test tool can help to test the throughput between different VPN peers.
Pepwave MAX and Surf User Manual 21.15 Wake-on-LAN Peplink routers can send special “magic packets” to any client specified from the Web UI. To access this feature, navigate to System > Tools > Wake-on-LAN Select a client from the drop-down list and click Send to send a “magic packet” 21.16 CLI (Command Line Interface Support) The CLI (command line interface) can be accessed via SSH. This field enables CLI support.
Pepwave MAX and Surf User Manual 22 Status 22.1 Device System information is located at Status>Device. System Information Router Name Model Product Code Hardware Revision Serial Number Firmware This is the name specified in the Router Name field located at System>Admin Security. This shows the model name and number of this device. If your model uses a product code, it will appear here. This shows the hardware version of this device. This shows the serial number of this device.
Pepwave MAX and Surf User Manual Remote Assistance Click Turn on to enable remote assistance. The second table shows the MAC address of each LAN/WAN interface connected. To view your device’s End User License Agreement (EULA), click . Important Note If you encounter issues and would like to contact the Pepwave Support Team (http://www.pepwave.com/contact/), please download the diagnostic report file and attach it along with a description of your issue. In Firmware 5.
Pepwave MAX and Surf User Manual 22.2 Active Sessions Information on active sessions can be found at Status>Active Sessions>Overview. This screen displays the number of sessions initiated by each application. Click on each service listing for additional information. This screen also indicates the number of sessions initiated by each WAN port. In addition, you can see which clients are initiating the most sessions. http://www.pepwave.
Pepwave MAX and Surf User Manual You can also perform a filtered search for specific sessions. You can filter by subnet, port, protocol, and interface. To perform a search, navigate to Status>Active Sessions>Search. This Active Sessions section displays the active inbound/outbound sessions of each WAN connection on the Pepwave router. A filter is available to sort active session information. Enter a keyword in the field or check one of the WAN connection boxes for filtering. http://www.pepwave.
Pepwave MAX and Surf User Manual 22.3 Client List The client list table is located at Status>Client List. It lists DHCP and online client IP addresses, names (retrieved from the DHCP reservation table or defined by users), current download and upload rate, and MAC address. Clients can be imported into the DHCP reservation table by clicking the button on the right. You can update the record after import by going to Network>LAN. If the PPTP server (see Section 19.2), SpeedFusionTM (see Section 12.
Pepwave MAX and Surf User Manual 22.5 UPnP / NAT-PMP The table that shows the forwarded ports under UPnP and NAT-PMP protocols is located at Status>UPnP/NAT-PMP. This section appears only if you have enabled UPnP / NAT-PMP as mentioned in Section 16.1.1. Click to delete a single UPnP / NAT-PMP record in its corresponding row. To delete all records, click Delete All on the right-hand side below the table.
Pepwave MAX and Surf User Manual Click the button for a chart displaying real-time throughput, latency, and droprate information for each WAN connection. When pressing the button, the following menu will appear: http://www.pepwave.
Pepwave MAX and Surf User Manual After clicking the icon, the following menu appears: Select the L2 protocol (TCP/UDP), direction, and duration and click the Start button to begin the general throughput test. http://www.pepwave.
Pepwave MAX and Surf User Manual The bandwidth bonding feature of PepVPN occurs when multiple WAN lines from one end merge with multiple WAN lines from the other end. For this to happen, each WAN line needs to form a connection with all the WAN lines on the opposite end. The function of the PepVPN analyzer is to report the throughput, packet loss, and latency of all possible combinations of connections.
Pepwave MAX and Surf User Manual 22.7 Event Log Event log information is located at Status>Event Log. The log section displays a list of events that has taken place on the Pepwave router. Check Auto Refresh to refresh log entries automatically. Click the Clear Log button to clear the log. 22.8 Bandwidth This section shows bandwidth usage statistics and is located at Status>Bandwidth. Bandwidth usage at the LAN while the device is switched off (e.g., LAN bypass) is neither recorded nor shown. http://www.
Pepwave MAX and Surf User Manual 22.8.1 Real-Time The Data transferred since installation table indicates how much network traffic has been processed by the device since the first bootup. The Data transferred since last reboot table indicates how much network traffic has been processed by the device since the last bootup. http://www.pepwave.
Pepwave MAX and Surf User Manual 22.8.2 Hourly This page shows the hourly bandwidth usage for all WAN connections, with the option of viewing each individual connection. Select the desired connection to check from the drop-down menu. 22.8.3 Daily http://www.pepwave.
Pepwave MAX and Surf User Manual This page shows the daily bandwidth usage for all WAN connections, with the option of viewing each individual connection. Select the connection to check from the drop-down menu. If you have enabled the Bandwidth Monitoring feature, the Current Billing Cycle table for that WAN connection will be displayed. Click on a date to view the client bandwidth usage of that specific date.
Pepwave MAX and Surf User Manual 22.8.4 Monthly This page shows the monthly bandwidth usage for each WAN connection. If you have enabled the Bandwidth Monitoring feature, you can check the usage of each particular connection and view the information by Billing Cycle or by Calendar Month. Click the first two rows to view the client bandwidth usage in the last two months. This feature is not available if you have chosen to view the bandwidth of an individual WAN connection.
Pepwave MAX and Surf User Manual Ethernet WAN Monthly Bandwidth Usage Tip By default, the scale of data size is in MB. 1GB equals 1024MB. http://www.pepwave.
Pepwave MAX and Surf User Manual Appendix A. Restoration of Factory Defaults To restore the factory default settings on a Pepwave router, follow the steps below: 1. Locate the reset button on the front or back panel of the Pepwave router. 2. With a paper clip, press the reset button and hold it for at least 10 seconds, until the unit reboots itself. After the Pepwave router finishes rebooting, the factory default settings will be restored.
Pepwave MAX and Surf User Manual Appendix B: Declaration 1. The device supports time division technology 2. Federal Communication Commission and Industry Canada Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
! " #$ %&' ( ) * &( + ) , - + ) - " "
Pepwave MAX and Surf User Manual Industry Canada Statement (for MAX Hotspot/ Surf SOHO/ MAX BR1 mini) This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Pepwave MAX and Surf User Manual Avertissement: (i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; (ii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5725 à 5 850 MHz) doit être conforme à la limite de la p.i.r.e.
Pepwave MAX and Surf User Manual Industry Canada Statement (for MAX HD2 LTE/LTEA) This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Pepwave MAX and Surf User Manual Radiation Exposure Statement: (for MAX HD2 LTE/LTEA) This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 37cm between the radiator & your body. 70cm minimum when the product is operated with a plug-in 3G USB device which has maximum of 7W ERP output power.
Pepwave MAX and Surf User Manual 3. CE Statement for Pepwave Routers Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.
Pepwave MAX and Surf User Manual - EN 301 489-17 V2.2.1: 2012 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment - EN 301 489-24 V1.5.
Pepwave MAX and Surf User Manual Lietuvių [Lithuanian] Nederlands [Dutch] Malti [Maltese] Magyar [Hungarian] Polski [Polish] Português [Portuguese] Slovensko [Slovenian] Slovensky [Slovak] Suomi [Finnish] Svenska [Swedish] Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Pepwave MAX and Surf User Manual 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用， 並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須 忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 本行動寬頻設備的行動寬頻頻段(LTE900/LTE1800) 警告使用者: 此為甲類資訊技術設備，於居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用者會被要求採 取某些適當的對策。 http://www.pepwave.
Contact Us: Sales http://www.pepwave.com/contact/sales/ Support http://www.pepwave.com/contact/ Business Development and Partnerships http://www.pepwave.
